BRP Outlander 2018 रखरखाव मैनुअल
BRP Outlander · 2018 · रखरखाव मैनुअल · 1259 पृष्ठ
तकनीकी डेटा
पूरी फ़ाइल बॉट द्वारा भेजी जाती है।
कसने का टॉर्क
पूरी फ़ाइल बॉट द्वारा भेजी जाती है।
| आइटम | मान | भी | PDF पृष्ठ |
|---|---|---|---|
| Tail pipe retaining screws | 11 ± 1.02 N·m | 97 in·lb | p. 20 |
| Magnetic drain plug | 20.3 ± 1.36 N·m | 15 ft·lb | p. 21 |
| Oil filter cover screws | 10.1 ± 1.02 N·m | 89 in·lb | p. 22 |
| Washer | 10 ± 1 N·m | p. 25 | |
| Coolant drain plug | 10.1 ± 1.02 N·m | 89 in·lb | p. 25 |
| Bleed screws | 5 ± 0.56 N·m | 44 in·lb | p. 26 |
| RH footrest panel | 5 ± 0.6 N·m | p. 27 | |
| Oil level plug | 5 ± 0.56 N·m | 44 in·lb | p. 27 |
| Washer | 20 ± 2 N·m | p. 28 | |
| Side panel and extension | 22.5 ± 2.5 N·m | p. 31 | |
| Filler plug | 23 ± 2.71 N·m | 17 ft·lb | p. 31 |
| Spark plug | 20.3 ± 1.36 N·m | 15 ft·lb | p. 31 |
| Drain plug | 7.5 ± 0.5 N·m | p. 31 | |
| Filler plug | 22.5 ± 2.5 N·m | p. 32 | |
| Wheel lug nuts | 100.3 ± 9.49 N·m | 74 ft·lb | p. 33 |
| Engine retaining bolts | 62.4 ± 8.13 N·m | 46 ft·lb | p. 51 |
| Nut facing outwards | 40 ± 1 N·m | p. 57 | |
| Nut facing outwards | 13 ± 1 N·m | p. 57 | |
| Twin Cylinder Models | 9 ± 1 N·m | p. 58 | |
| Nut facing outwards | 10 ± 2 N·m | p. 58 | |
| Taining nuts | 13 ± 1 N·m | p. 61 | |
| Head pipe nuts | 13 ± 1.02 N·m | 115 in·lb | p. 61 |
| Rear cylinder | 13 ± 1.02 N·m | 115 in·lb | p. 62 |
| Oil Strainer screws | 6 ± 0.7 N·m | p. 80 | |
| Thermostat cover | 6 ± 0.7 N·m | p. 87 | |
| Retaining screws | 6 ± 0.68 N·m | 53 in·lb | p. 87 |
| Radiator upper retaining | 10 ± 2 N·m | p. 88 | |
| Radiator cooling fan | 10 ± 2 N·m | p. 90 | |
| Water pump housing | 10 ± 1 N·m | p. 91 | |
| Regulator/rectifier (P/N 529 035 868) | 10.1 ± 1.02 N·m | 89 in·lb | p. 104 |
| Holding strip screws | 4 ± 0.45 N·m | 35 in·lb | p. 106 |
| Stator retaining screws | 10.1 ± 1.02 N·m | 89 in·lb | p. 106 |
| Rotor retaining screw | 150.5 ± 9.49 N·m | 111 ft·lb | p. 107 |
| Sprag clutch housing | 30 ± 2 N·m | p. 109 | |
| Starter mounting screw | 25 ± 3 N·m | p. 111 | |
| Retaining nut | 6 ± 0.45 N·m | 53 in·lb | p. 111 |
| Intake manifold | 20 ± 2 N·m | p. 114 | |
| Retaining screws | 20.3 ± 1.36 N·m | 15 ft·lb | p. 114 |
| Valve cover retaining | 7 ± 0.8 N·m | p. 121 | |
| M6 cylinder head | 10 ± 1 N·m | p. 128 | |
| M10 x 140 screws | 10.1 ± 1.02 N·m | 89 in·lb | p. 128 |
| Camshaft timing gear | 10 ± 1 N·m | p. 148 | |
| Timing chain guide | 10 ± 1 N·m | p. 153 | |
| Bearing screw | 10.1 ± 1.02 N·m | 89 in·lb | p. 153 |
| Rear bearing cover | 10 ± 1 N·m | p. 158 | |
| Front bearing cover | 10 ± 1 N·m | p. 159 | |
| PTO cover screws | 10 ± 1 N·m | p. 163 | |
| 570, 650 and 850 Engines screws | 29.8 ± 1.36 N·m | 22 ft·lb | p. 175 |
| CVT cover screws | 7 ± 1.02 N·m | 62 in·lb | p. 205 |
| CVT hose clamps | 2.5 ± 0.45 N·m | 22 in·lb | p. 205 |
| Lock nuts | 8 ± 1 N·m | p. 214 | |
| Threaded stud | 50 ± 2 N·m | p. 216 | |
| Drive pulley nut | 80 ± 1 N·m | p. 216 | |
| REQUIRED TOOL Stud | 44.7 ± 1.36 N·m | 33 ft·lb | p. 224 |
| Counter nut | 35.3 ± 1.36 N·m | 26 ft·lb | p. 227 |
| VSS retaining screw | 10 ± 1 N·m | p. 235 | |
| Indicator switches | 2.5 ± 0.34 N·m | 22 in·lb | p. 236 |
| Actuator screws | 24.4 ± 2.71 N·m | 18 ft·lb | p. 239 |
| M8 screws | 25 ± 3 N·m | p. 246 | |
| Right housing | 24.4 ± 2.71 N·m | 18 ft·lb | p. 246 |
| Right housing | 10 ± 1 N·m | p. 246 | |
| Gear housing | 10 ± 1 N·m | p. 262 | |
| Gearbox retaining nuts | 24.4 ± 2.71 N·m | 18 ft·lb | p. 263 |
| GBPS retaining screws | 10.1 ± 1.02 N·m | 89 in·lb | p. 272 |
| GBPS retaining screws | 3 ± 0.3 N·m | p. 272 | |
| Indicator switch | 3.1 ± 0.34 N·m | 27 in·lb | p. 272 |
| Set ignition switch | 2.7 N·m | 2 ft·lb | p. 274 |
| Shaft CVT side | 25 ± 3 N·m | p. 289 | |
| Shaft CVT side | 24.4 ± 2.71 N·m | 18 ft·lb | p. 289 |
| Shift plate nut | 9 ± 1 N·m | p. 301 | |
| Battery ground | 3 N·m | 27 in·lb | p. 364 |
| CPS retaining screw | 10 ± 1 N·m | p. 367 | |
| MAPTS retaining screw | 6 ± 0.68 N·m | 53 in·lb | p. 370 |
| Fuel tank retaining | 6.5 ± 0.5 N·m | p. 382 | |
| Fuel pump retaining nut | 28.5 ± 1.36 N·m | 21 ft·lb | p. 386 |
| Ignition coil retaining bolt | 8 ± 1 N·m | p. 413 | |
| Battery retaining plate | 4.5 ± 0.5 N·m | p. 420 | |
| Air intake tube retaining | 1.6 ± 0.4 N·m | p. 459 | |
| Clamping screw | 4.5 ± 0.5 N·m | p. 460 | |
| Clamping screw | 0.4 ± 0.1 N·m | p. 460 | |
| Handlebar tip screw | 0.5 ± 0.11 N·m | 4 in·lb | p. 460 |
| Winch retaining screws | 16 ± 2.03 N·m | 142 in·lb | p. 465 |
| Winch retaining screws | 7 ± 5 N·m | p. 465 | |
| Visco-Lok / ring gear | 37 ± 3 N·m | p. 476 | |
| Differential housing | 23.5 ± 3.5 N·m | p. 476 | |
| Pinion nut | 180 ± 15 N·m | p. 476 | |
| Front propeller shaft | 75 ± 5 N·m | p. 476 | |
| Adapter retaining screw | 74.6 ± 5.42 N·m | 55 ft·lb | p. 476 |
| M8 nut securing front | 24.5 ± 3.5 N·m | p. 477 | |
| M10 nuts securing front | 61 ± 9 N·m | p. 477 | |
| Hi-temp bearing grease | 75 ± 5 N·m | p. 480 | |
| Wheel hub nut | 204.7 ± 14.91 N·m | 151 ft·lb | p. 482 |
| Propeller shaft screw | 75 ± 5 N·m | p. 486 | |
| Proper grease fitting location | 74.6 ± 5.42 N·m | 55 ft·lb | p. 486 |
| PRELOAD gear | 0.6 N·m | 5 in·lb | p. 489 |
| Final drive housing | 32 ± 3 N·m | p. 492 |
क्षमताएँ
पूरी फ़ाइल बॉट द्वारा भेजी जाती है।
| आइटम | मान | भी | PDF पृष्ठ |
|---|---|---|---|
| Fuel tank | 20.5 L | p. 651 |
स्पार्क प्लग
पूरी फ़ाइल बॉट द्वारा भेजी जाती है।
| आइटम | मान | भी | PDF पृष्ठ |
|---|---|---|---|
| M10 | — | p. 126 | |
| Spark plug | 0.7 mm | p. 626 |
सर्विस अंतराल
पूरी फ़ाइल बॉट द्वारा भेजी जाती है।
| आइटम | मान | भी | PDF पृष्ठ |
|---|---|---|---|
| Brake inspection | 2 years | p. 15 |
दस्तावेज़ प्राप्त करें
पूरी फ़ाइल बॉट द्वारा भेजी जाती है।
Telegram में खोलें — बॉट इस दस्तावेज़ को उसके कैटलॉग id से ढूँढता है और फ़ाइल भेजता है।
बॉट में खोलें- पुर्जा सूचीसभी मैनुअल