Ski-Doo MY21 Skandic Pdf 2021 매뉴얼
Ski-Doo MY21 Skandic Pdf · 2021 · 매뉴얼 · 665페이지
기술 데이터
전체 파일은 봇이 전송합니다.
체결 토크
전체 파일은 봇이 전송합니다.
| 항목 | 값 | 추가 | PDF 페이지 |
|---|---|---|---|
| Spark plug | 28.5 ± 1.36 N·m | 21 ft·lb | p. 44 |
| INTAKE SYSTEM subsection | 31.2 ± 4.07 N·m | 23 ft·lb | p. 60 |
| Snug all bolts | 33 ± 3 N·m | p. 60 | |
| Engine rubber mount | 24.5 ± 3.5 N·m | p. 69 | |
| Engine support screws | 42 ± 4.07 N·m | 31 ft·lb | p. 70 |
| Front Engine Support Replacement | 42 ± 4 N·m | p. 71 | |
| ENGINE RUBBER MOUNTS Engine rubber mount | 10 ± 2 N·m | p. 72 | |
| Engine support screws | 31.2 ± 4.07 N·m | 23 ft·lb | p. 78 |
| Muffler retaining screw | 7 ± 1.02 N·m | 62 in·lb | p. 97 |
| Exhaust Gas | 45 ± 2 N·m | p. 102 | |
| Temperature Sensor | 44.7 ± 1.36 N·m | 33 ft·lb | p. 102 |
| Exhaust pipe retaining | 7 ± 1 N·m | p. 105 | |
| Cylinder | 5.5 ± 0.5 N·m | p. 121 | |
| Head | 5.5 ± 0.45 N·m | 49 in·lb | p. 121 |
| Coolant hose clamp | 3.1 ± 0.45 N·m | 27 in·lb | p. 123 |
| Turbo engine | 2.5 ± 0.5 N·m | p. 131 | |
| Drain screws | 9 ± 1 N·m | p. 133 | |
| M6 screw on chassis | 10 ± 2 N·m | p. 220 | |
| Engine Ground | 31.2 ± 4.07 N·m | 23 ft·lb | p. 226 |
| Approved spark plug socket | 27.5 ± 2.5 N·m | p. 281 | |
| Engine Cut-Off Switch Continuity Test | 9 ± 1 N·m | p. 286 | |
| Spark plug | 23 ± 1.36 N·m | 17 ft·lb | p. 300 |
| Ignition coil retaining | 2.4 ± 0.2 N·m | p. 303 | |
| Battery terminals | 10 ± 2 N·m | p. 308 | |
| Battery hold down | 7 ± 1 N·m | p. 308 | |
| Bracket | 7 ± 1.02 N·m | 62 in·lb | p. 308 |
| Battery cover retaining | 7 ± 1 N·m | p. 308 | |
| Capacitor screws | 2 N·m | 18 in·lb | p. 314 |
| Solenoid cable retaining | 4 ± 0.5 N·m | p. 325 | |
| Taillight retaining screw | 0.8 ± 0.23 N·m | 7 in·lb | p. 354 |
| Retaining screws | 1 ± 0.23 N·m | 9 in·lb | p. 358 |
| Torx screw | 7.5 ± 1.02 N·m | 66 in·lb | p. 383 |
| Elastic nut | 10.1 ± 2.03 N·m | 89 in·lb | p. 383 |
| Clamping screw | 5.5 ± 0.45 N·m | 49 in·lb | p. 385 |
| Distorted spare belt | 10 ± 2 N·m | p. 389 | |
| Distorted spare belt | 24.5 ± 3.5 N·m | p. 389 | |
| Roller axle screw | 5 ± 0.45 N·m | 44 in·lb | p. 402 |
| Damper screws | 31.2 ± 4.07 N·m | 23 ft·lb | p. 403 |
| Centrifugal lever | 5 ± 0.6 N·m | p. 412 | |
| Pivot nut | 5 ± 0.56 N·m | 44 in·lb | p. 412 |
| Spring cover retaining | 10 ± 2 N·m | p. 412 | |
| Drive pulley bolt | 120 N·m | p. 426 | |
| Drive pulley bolt First | 120.7 N·m | 89 ft·lb | p. 426 |
| Bearing flange nut | 15.5 ± 1.47 N·m | 137 in·lb | p. 435 |
| Pivot screws | 16.9 ± 1.02 N·m | 150 in·lb | p. 445 |
| Brake lever pivot nut | 6 ± 1 N·m | p. 467 | |
| Brake lever pivot nut | 8.5 ± 1.5 N·m | p. 467 | |
| Brake caliper bleeder | 8.5 ± 1.47 N·m | 75 in·lb | p. 467 |
| Brake pad pin | 10.1 ± 2.03 N·m | 89 in·lb | p. 469 |
| Master cylinder clamp | 9 ± 1 N·m | p. 472 | |
| Washers | 27 ± 1 N·m | p. 472 | |
| Middle clamp nut | 2.3 ± 0.23 N·m | 20 in·lb | p. 474 |
| Middle clamp nut | 35 ± 1 N·m | p. 474 | |
| Caliper Banjo fitting | 35.3 ± 1.36 N·m | 26 ft·lb | p. 474 |
| Master cylinder Banjo | 27 ± 1 N·m | p. 474 | |
| Caliper Banjo fitting | 27.1 ± 1.36 N·m | 20 ft·lb | p. 474 |
| Magnetic check plug | 6 ± 1 N·m | p. 477 | |
| Drain plug | 6 ± 1.02 N·m | 53 in·lb | p. 478 |
| Bearing | 24.5 ± 3.5 N·m | p. 484 | |
| Filler plug | 8 ± 1.02 N·m | 71 in·lb | p. 493 |
| Shift lever retaining | 10 ± 2 N·m | p. 495 | |
| Actuator coupling | 7 ± 0.5 N·m | p. 496 | |
| Shaft nut | 7 ± 0.45 N·m | 62 in·lb | p. 496 |
| Coupling shaft nut | 10 ± 2 N·m | p. 496 | |
| Actuator support screws | 10.1 ± 2.03 N·m | 89 in·lb | p. 496 |
| M8 x 35 screw | 16 ± 2 N·m | p. 510 | |
| Rear idler wheel | 48 ± 6 N·m | p. 521 | |
| Retaining screws | 47.5 ± 5.42 N·m | 35 ft·lb | p. 521 |
| Rear idler wheel | 24.5 ± 3.5 N·m | p. 521 | |
| Cover retaining screws | 24.4 ± 4.07 N·m | 18 ft·lb | p. 531 |
| Cover retaining screws | 29 ± 3 N·m | p. 531 | |
| Shock rod nut | 28.5 ± 2.71 N·m | 21 ft·lb | p. 531 |
| Suspension | 24.5 ± 3.5 N·m | p. 538 | |
| Suspension | 48 ± 6 N·m | p. 539 | |
| Suspension | 3 ± 0.5 N·m | p. 539 | |
| 16in Wide Suspension | 1.5 ± 0.5 N·m | p. 541 | |
| Front and rear arm | 48 ± 6 N·m | p. 546 | |
| Front arm upper bolts | 61 ± 9.49 N·m | 45 ft·lb | p. 546 |
| Front arm upper bolts | 82.5 ± 7.5 N·m | p. 546 | |
| Rear arm upper bolts | 82.7 ± 8.13 N·m | 61 ft·lb | p. 546 |
| Rear shock absorber | 24.5 ± 3.5 N·m | p. 549 | |
| Center shock shaft | 70 ± 10 N·m | p. 550 | |
| Retaining nut | 70.5 ± 9.49 N·m | 52 ft·lb | p. 550 |
| Center shock shaft | 85 ± 10 N·m | p. 550 | |
| Retaining screws | 85.4 ± 9.49 N·m | 63 ft·lb | p. 550 |
| Shock absorber upper bolt | 61 ± 9.49 N·m | 45 ft·lb | p. 553 |
| Unfasten stopper strap | 48 ± 6 N·m | p. 553 | |
| Front arm upper bolts | 47.5 ± 5.42 N·m | 35 ft·lb | p. 553 |
| Lower bolts | 61 ± 9.49 N·m | 45 ft·lb | p. 553 |
| Jam nut | 18.5 ± 3.5 N·m | 164 in·lb | p. 563 |
| Runner nut | 8 ± 1.02 N·m | 71 in·lb | p. 564 |
| Ski nut | 47.5 ± 5.42 N·m | 35 ft·lb | p. 565 |
| Adjusting knob screw | 9 ± 1.02 N·m | 80 in·lb | p. 568 |
| Adjusting knob screw | 24.5 ± 3.5 N·m | p. 568 | |
| Indicator screw | 9 ± 1.02 N·m | 80 in·lb | p. 568 |
| Indicator screw | 24.5 ± 3.5 N·m | p. 568 | |
| Multifunction switch | 2.4 ± 0.2 N·m | p. 571 |
정비 주기
전체 파일은 봇이 전송합니다.
| 항목 | 값 | 추가 | PDF 페이지 |
|---|---|---|---|
| Drive chain service | 500 km | p. 37 | |
| Coolant change | 5 years | p. 38 | |
| Engine oil change | 2 years | p. 40 | |
| Brake inspection | 3 years | p. 40 |
문서 받기
전체 파일은 봇이 전송합니다.
Telegram에서 열기 — 봇이 카탈로그 id로 이 문서를 찾아 파일을 전송합니다.
봇에서 열기- 부품 카탈로그전체 매뉴얼