Arctic Cat All Models 2012 Instrukcja serwisowa
Arctic Cat · 2012 · Instrukcja serwisowa · 470 stron
Dane techniczne
Poniższe liczby zostały wyodrębnione automatycznie z dokumentu. Sprawdź je w oryginalnej instrukcji przed zamówieniem części lub dokręcaniem.
Moment dokręcania
Wartości wyodrębnione z tekstu dokumentu. Sprawdź je z oryginałem przed pracami serwisowymi.
| Pozycja | Wartość | Także | Strona PDF |
|---|---|---|---|
| Steering Post | 13.6 N·m | 120 in·lb | p. 18 |
| Drive Clutch Cover Movable Sheave | 13.6 N·m | 120 in·lb | p. 18 |
| Driven Pulley Input Shaft 32 Steering Arm Chassis | 10.8 N·m | 96 in·lb | p. 18 |
| Movable Sheave Bracket | 8.1 N·m | 72 in·lb | p. 18 |
| Shift Actuator Gear Case | 4.6 N·m | 41 in·lb | p. 18 |
| Shock Mount Frame Suspension Mounting | 10.8 N·m | 96 in·lb | p. 18 |
| Cam Arm Set Screw Cam Arm | 2.1 N·m | 19 in·lb | p. 18 |
| Chain Case (Cap Screw) Chassis | 10.8 N·m | 96 in·lb | p. 18 |
| Shift Actuator (1100 cc) Chain Case Cover | 4.1 N·m | 36 in·lb | p. 18 |
| Fan Drive Clutch Cover | 6.8 N·m | 60 in·lb | p. 18 |
| Upper Bearing Bracket Support Plate | 10.8 N·m | 96 in·lb | p. 18 |
| Front Bumper (Bearcat XT) Shock Mounting Bracket | 13.6 N·m | 120 in·lb | p. 18 |
| End Cap Rail | 9 N·m | 80 in·lb | p. 19 |
| Rear Idler Wheel Rear Idler Wheel | 9 N·m | 80 in·lb | p. 19 |
| Limiter Strap Rail Support | 8.1 N·m | 72 in·lb | p. 19 |
| Limiter Strap (BC 570/T-Series) Front Arm | 8.1 N·m | 72 in·lb | p. 19 |
| Cap screws | 67.8 N·m | 50 ft·lb | p. 34 |
| Cap screws | 23 N·m | 17 ft·lb | p. 42 |
| Exhaust mani | 33.9 N·m | 25 ft·lb | p. 42 |
| Exhaust mani | 23 N·m | 17 ft·lb | p. 42 |
| Front shock mount cap screws | 16.3 N·m | 12 ft·lb | p. 42 |
| Top rear screws | 19 N·m | 14 ft·lb | p. 43 |
| Cap screws | 33.9 N·m | 25 ft·lb | p. 43 |
| Brackets | 27.1 N·m | 20 ft·lb | p. 43 |
| Head | 50.2 N·m | 37 ft·lb | p. 56 |
| Severe engine damage | 10.2 N·m | 7.5 ft·lb | p. 60 |
| Carriage bolt and lock nuts | 16.3 N·m | 12 ft·lb | p. 72 |
| Bracket cap screws | 27.1 N·m | 20 ft·lb | p. 75 |
| Shock mounting | 31.2 N·m | 23 ft·lb | p. 75 |
| Chain case | 31.2 N·m | 23 ft·lb | p. 75 |
| Flange nuts | 16.3 N·m | 12 ft·lb | p. 77 |
| Reed valves and reed valve stoppers | 10.8 N·m | 96 in·lb | p. 90 |
| Cap screws | 38 N·m | 28 ft·lb | p. 97 |
| Allen-head cap screws | 5.4 N·m | 48 in·lb | p. 98 |
| Cap screws evenly | 25.8 N·m | 19 ft·lb | p. 114 |
| Wheel cap screw | 67.8 N·m | 50 ft·lb | p. 114 |
| Case halves | 42 N·m | 31 ft·lb | p. 127 |
| Cylinder base nuts and cap screws | 59.7 N·m | 44 ft·lb | p. 131 |
| Allen-head cap scr | 10.8 N·m | 96 in·lb | p. 132 |
| Allen-head cap screws | 9.5 N·m | 84 in·lb | p. 148 |
| Screws evenly | 33.9 N·m | 25 ft·lb | p. 149 |
| Cap screws 1-6 | 17.6 N·m | 13 ft·lb | p. 150 |
| Cap screws 7-24 | 13.6 N·m | 120 in·lb | p. 150 |
| Cap screws 1-6 | 44.7 N·m | 33 ft·lb | p. 150 |
| Union bolt | 70.5 N·m | 52 ft·lb | p. 150 |
| Cap screws 1-6 initially | 24.4 N·m | 18 ft·lb | p. 152 |
| Flange nuts 7-8 | 24.4 N·m | 18 ft·lb | p. 152 |
| C. Flange nuts 9-10 | 13.6 N·m | 10 ft·lb | p. 152 |
| D. Flange nuts 11-12 | 24.4 N·m | 18 ft·lb | p. 152 |
| Spring, and tensioner bolt | 24.4 N·m | 18 ft·lb | p. 153 |
| Outer spacer | 9.5 N·m | 84 in·lb | p. 154 |
| Perature sensor | 20.3 N·m | 15 ft·lb | p. 154 |
| Lock nuts | 14.9 N·m | 11 ft·lb | p. 156 |
| Lock nuts | 40.7 N·m | 30 ft·lb | p. 156 |
| Changing Oil/Filter | 20.3 N·m | 15 ft·lb | p. 174 |
| Magneto case | 6.8 N·m | 60 in·lb | p. 183 |
| Lock nuts | 20.3 N·m | 15 ft·lb | p. 191 |
| Exhaust manifold | 20.3 N·m | 15 ft·lb | p. 192 |
| Exhaust springs | 6.3 N·m | 56 in·lb | p. 197 |
| Exhaust manifold | 40.7 N·m | 30 ft·lb | p. 197 |
| Vent hose, and fuel pump harness | 31.2 N·m | 23 ft·lb | p. 233 |
| Sensor and harness clamp | 9.5 N·m | 84 in·lb | p. 253 |
| Drive Belt driven pulley | 43.4 N·m | 32 ft·lb | p. 294 |
| Head screws | 2.7 N·m | 24 in·lb | p. 304 |
| Brake caliper housing | 23 N·m | 17 ft·lb | p. 308 |
| Retaining nut | 162.7 N·m | 120 ft·lb | p. 308 |
| Drain plug | 16.3 N·m | 12 ft·lb | p. 316 |
| Self-tapping screws | 11.9 N·m | 105 in·lb | p. 319 |
| Guard | 27.1 N·m | 20 ft·lb | p. 320 |
| Cover cap screws | 10.8 N·m | 8 ft·lb | p. 320 |
| Idler wheel axle cap screws | 46.1 N·m | 34 ft·lb | p. 333 |
| Axle cap screws | 27.1 N·m | 20 ft·lb | p. 334 |
| Cap screws | 54.2 N·m | 40 ft·lb | p. 364 |
| Axle tube | 54.2 N·m | 40 ft·lb | p. 380 |
| Lock nuts | 54.2 N·m | 40 ft·lb | p. 386 |
| Idler spacer, and washer | 13.6 N·m | 120 in·lb | p. 412 |
| Lock nut | 47.5 N·m | 35 ft·lb | p. 443 |
| Steering Tie Rod | 27.1 N·m | 20 ft·lb | p. 451 |
| Mounting Bracket | 31.2 N·m | 23 ft·lb | p. 458 |
Świece zapłonowe
Wartości wyodrębnione z tekstu dokumentu. Sprawdź je z oryginałem przed pracami serwisowymi.
| Pozycja | Wartość | Także | Strona PDF |
|---|---|---|---|
| MR8AI-9 | — | p. 10 | |
| BR9EYA | — | p. 10 | |
| Spark plug | 0.01–0.02 in | p. 107 | |
| Spark plug | 0.01–0.02 in | p. 124 |
Pobierz dokument
Pełny plik dostarcza bot. Bezpłatne instrukcje właściciela dla Arctic Cat są również dostępne u producenta.
Otwórz w Telegramie — bot znajduje ten dokument po identyfikatorze katalogowym i wysyła plik.
Otwórz w bocie- Oficjalne bezpłatne instrukcje właściciela Arctic CatKatalog częściWszystkie instrukcje