Ski-Doo MY23 Renegade Pdf 2023 Instrukcja
Ski-Doo MY23 Renegade Pdf · 2023 · Instrukcja · 805 stron
Dane techniczne
Pełny plik dostarcza bot.
Moment dokręcania
Pełny plik dostarcza bot.
| Pozycja | Wartość | Także | Strona PDF |
|---|---|---|---|
| Spark plug | 28.5 ± 1.36 N·m | 21 ft·lb | p. 46 |
| INTAKE SYSTEM subsection | 31.2 ± 4.07 N·m | 23 ft·lb | p. 62 |
| Snug all bolts | 33 ± 3 N·m | p. 62 | |
| Engine rubber mount | 24.5 ± 3.5 N·m | p. 71 | |
| Engine support screws | 42 ± 4.07 N·m | 31 ft·lb | p. 72 |
| Front Engine Support Replacement | 42 ± 4 N·m | p. 73 | |
| ENGINE RUBBER MOUNTS Engine rubber mount | 10 ± 2 N·m | p. 74 | |
| Engine support screws | 31.2 ± 4.07 N·m | 23 ft·lb | p. 80 |
| Muffler retaining screw | 7 ± 1.02 N·m | 62 in·lb | p. 99 |
| Exhaust Gas | 45 ± 2 N·m | p. 104 | |
| Temperature Sensor | 44.7 ± 1.36 N·m | 33 ft·lb | p. 104 |
| Exhaust pipe retaining | 7 ± 1 N·m | p. 107 | |
| Cylinder | 5.5 ± 0.5 N·m | p. 123 | |
| Head | 5.5 ± 0.45 N·m | 49 in·lb | p. 123 |
| Coolant hose clamp | 3.1 ± 0.45 N·m | 27 in·lb | p. 125 |
| Turbo engine | 2.5 ± 0.5 N·m | p. 133 | |
| Drain screws | 9 ± 1 N·m | p. 135 | |
| M6 screw on chassis | 10 ± 2 N·m | p. 226 | |
| Approved spark plug socket | 27.5 ± 2.5 N·m | p. 283 | |
| Spark plug | 23 ± 1.36 N·m | 17 ft·lb | p. 296 |
| Ignition coil retaining | 2.4 ± 0.2 N·m | p. 299 | |
| Battery terminals | 10 ± 2 N·m | p. 304 | |
| Battery hold down | 5 ± 0.5 N·m | p. 304 | |
| Bracket | 5 ± 0.45 N·m | 44 in·lb | p. 304 |
| Battery cover retaining | 7 ± 1 N·m | p. 304 | |
| Battery hold down | 7 ± 1 N·m | p. 315 | |
| Bracket | 7 ± 1.02 N·m | 62 in·lb | p. 315 |
| Solenoid cable retaining | 4 ± 0.5 N·m | p. 321 | |
| CONNECTOR CONNECTOR retaining screws | 1 ± 0.23 N·m | 9 in·lb | p. 353 |
| Torx screw | 7.5 ± 1.02 N·m | 66 in·lb | p. 375 |
| Elastic nut | 10.1 ± 2.03 N·m | 89 in·lb | p. 375 |
| Clamping screw | 5.5 ± 0.45 N·m | 49 in·lb | p. 377 |
| Distorted spare belt | 10 ± 2 N·m | p. 381 | |
| Distorted spare belt | 24.5 ± 3.5 N·m | p. 381 | |
| Roller axle screw | 5 ± 0.45 N·m | 44 in·lb | p. 394 |
| Damper screws | 31.2 ± 4.07 N·m | 23 ft·lb | p. 395 |
| Centrifugal lever | 5 ± 0.6 N·m | p. 404 | |
| Pivot nut | 5 ± 0.56 N·m | 44 in·lb | p. 404 |
| Spring cover retaining | 10 ± 2 N·m | p. 404 | |
| Drive pulley bolt | 120 N·m | p. 418 | |
| Drive pulley bolt First | 120.7 N·m | 89 ft·lb | p. 418 |
| Bearing flange nut | 15.5 ± 1.47 N·m | 137 in·lb | p. 427 |
| Pivot screws | 17 ± 1 N·m | 150 in·lb | p. 438 |
| Brake lever pivot nut | 6 ± 1 N·m | p. 447 | |
| Brake lever pivot nut | 8.5 ± 1.5 N·m | p. 447 | |
| Brake caliper bleeder | 8.5 ± 1.47 N·m | 75 in·lb | p. 447 |
| Brake pad pin | 10.1 ± 2.03 N·m | 89 in·lb | p. 449 |
| Master cylinder clamp | 9 ± 1 N·m | p. 452 | |
| Washers | 27 ± 1 N·m | p. 452 | |
| Middle clamp nut | 2.3 ± 0.23 N·m | 20 in·lb | p. 454 |
| Middle clamp nut | 35 ± 1 N·m | p. 454 | |
| Caliper Banjo fitting | 35.3 ± 1.36 N·m | 26 ft·lb | p. 454 |
| Master cylinder Banjo | 27 ± 1 N·m | p. 454 | |
| Caliper Banjo fitting | 27.1 ± 1.36 N·m | 20 ft·lb | p. 454 |
| Magnetic check plug | 6 ± 1 N·m | p. 457 | |
| Drain plug | 6 ± 1.02 N·m | 53 in·lb | p. 458 |
| Bearing | 24.5 ± 3.5 N·m | p. 464 | |
| Actuator coupling | 7 ± 0.5 N·m | p. 476 | |
| 219100985-021-010 shaft nut | 7 ± 0.45 N·m | 62 in·lb | p. 476 |
| Upper gear screw | 48 ± 6 N·m | p. 488 | |
| Screws Same | 10 ± 2 N·m | p. 489 | |
| Reverse gear screw | 24.4 ± 4.07 N·m | 18 ft·lb | p. 489 |
| Rear idler wheel | 48 ± 6 N·m | p. 499 | |
| Retaining screws | 47.5 ± 5.42 N·m | 35 ft·lb | p. 499 |
| Rear idler wheel | 24.5 ± 3.5 N·m | p. 499 | |
| Front shock absorber | 31.5 ± 3.5 N·m | p. 533 | |
| Retaining nuts | 31.2 ± 4.07 N·m | 23 ft·lb | p. 533 |
| Front arm bolts | 47.5 ± 5.42 N·m | 35 ft·lb | p. 547 |
| Rear arm connecting | 61 N·m | p. 547 | |
| Rod screws | 61 ± 9.49 N·m | 45 ft·lb | p. 547 |
| Clamp screws | 2.5 ± 0.45 N·m | 22 in·lb | p. 548 |
| Clamp screws | 0.4 ± 0.1 N·m | p. 548 | |
| Knob screw | 0.5 ± 0.11 N·m | 4 in·lb | p. 548 |
| Support screws | 5 ± 1.02 N·m | 44 in·lb | p. 550 |
| Support screws | 2.5 ± 0.5 N·m | p. 550 | |
| Clamp screws | 1.5 ± 0.5 N·m | p. 550 | |
| Bleeding and Reassembling Spring | 24.4 ± 4.07 N·m | 18 ft·lb | p. 553 |
| Banjo bolt | 24.4 ± 4.07 N·m | 18 ft·lb | p. 554 |
| Suspension | 24.5 ± 3.5 N·m | p. 570 | |
| Front and rear arm | 48 ± 6 N·m | p. 574 | |
| Upper bolts | 47.5 ± 5.42 N·m | 35 ft·lb | p. 574 |
| Rear shock absorber | 24.5 ± 3.5 N·m | p. 575 | |
| Nuts and bolts | 24.4 ± 4.07 N·m | 18 ft·lb | p. 575 |
| Center shock absorber | 48 ± 6 N·m | p. 576 | |
| Center shock absorber | 70 ± 10 N·m | p. 576 | |
| Rear arm top axle screws | 48 ± 6 N·m | p. 577 | |
| Pipe sealant | 13 ± 1 N·m | p. 584 | |
| Pipe sealant | 9 ± 1 N·m | p. 585 | |
| Pressure sensor | 27.1 ± 2.71 N·m | 20 ft·lb | p. 594 |
| Suspension | 13 ± 2 N·m | p. 602 | |
| Jam nuts | 18.5 ± 3.5 N·m | 164 in·lb | p. 605 |
| Runner nut | 8 ± 1.02 N·m | 71 in·lb | p. 606 |
Pojemności
Pełny plik dostarcza bot.
| Pozycja | Wartość | Także | Strona PDF |
|---|---|---|---|
| Fuel tank | 36 L | p. 775 |
Świece zapłonowe
Pełny plik dostarcza bot.
| Pozycja | Wartość | Także | Strona PDF |
|---|---|---|---|
| Spark plug | 0.4 mm | p. 472 |
Pobierz dokument
Pełny plik dostarcza bot.
Otwórz w Telegramie — bot znajduje ten dokument po identyfikatorze katalogowym i wysyła plik.
Otwórz w bocie- Katalog częściWszystkie instrukcje
Powiązane dokumenty
- Ski-Doo MX-Z/Formula/Summit/Grand Touring/Skandic 1997 Instrukcja serwisowa
- Ski-Doo REV Series 2004 Instrukcja serwisowa
- Ski-Doo RT Series 2005 Instrukcja serwisowa
- Ski-Doo Drive ACE Gen4 2024 Instrukcja serwisowa
- Ski-Doo Drive EFI 16 2024 Instrukcja serwisowa
- Ski-Doo Drive ETEC Gen5 2024 Instrukcja serwisowa