Ski-Doo MY21 Backcountry Pdf 2021 Kılavuz
Ski-Doo MY21 Backcountry Pdf · 2021 · Kılavuz · 405 sayfa
Teknik veriler
Dosyanın tamamı bot tarafından gönderilir.
Sıkma torku
Dosyanın tamamı bot tarafından gönderilir.
| Kalem | Değer | Ayrıca | PDF sayfası |
|---|---|---|---|
| Spark plug | 28.5 ± 1.36 N·m | 21 ft·lb | p. 30 |
| INTAKE SYSTEM subsection | 31.2 ± 4.07 N·m | 23 ft·lb | p. 42 |
| Snug all bolts | 33 ± 3 N·m | p. 42 | |
| Muffler retaining screw | 7 ± 1.02 N·m | 62 in·lb | p. 55 |
| Exhaust Gas | 45 ± 2 N·m | p. 60 | |
| Temperature Sensor | 44.7 ± 1.36 N·m | 33 ft·lb | p. 60 |
| Cylinder | 5.5 ± 0.5 N·m | p. 63 | |
| Head | 5.5 ± 0.45 N·m | 49 in·lb | p. 63 |
| Coolant hose clamp | 3.1 ± 0.45 N·m | 27 in·lb | p. 65 |
| M6 screw on chassis | 10 ± 2 N·m | p. 122 | |
| Approved spark plug socket | 27.5 ± 2.5 N·m | p. 161 | |
| Spark plug | 23 ± 1.36 N·m | 17 ft·lb | p. 170 |
| Ignition coil retaining | 2.4 ± 0.2 N·m | p. 173 | |
| Battery terminals | 10 ± 2 N·m | p. 178 | |
| Battery hold down | 5 ± 0.5 N·m | p. 178 | |
| Bracket | 5 ± 0.45 N·m | 44 in·lb | p. 178 |
| Battery cover retaining | 7 ± 1 N·m | p. 178 | |
| Solenoid cable retaining | 4 ± 0.5 N·m | p. 189 | |
| Retaining screws | 1 ± 0.23 N·m | 9 in·lb | p. 204 |
| Torx screw | 7.5 ± 1.02 N·m | 66 in·lb | p. 217 |
| Elastic nut | 10.1 ± 2.03 N·m | 89 in·lb | p. 217 |
| Clamping screw | 5.5 ± 0.45 N·m | 49 in·lb | p. 219 |
| Roller axle screw | 5 ± 0.45 N·m | 44 in·lb | p. 230 |
| Damper screws | 31.2 ± 4.07 N·m | 23 ft·lb | p. 231 |
| Drive pulley bolt | 120 ± 5 N·m | p. 232 | |
| Drive pulley bolt First | 120.7 N·m | 89 ft·lb | p. 244 |
| Bearing flange nut | 15.5 ± 1.47 N·m | 137 in·lb | p. 253 |
| Brake lever pivot nut | 6 ± 1 N·m | p. 259 | |
| Brake lever pivot nut | 8.5 ± 1.5 N·m | p. 259 | |
| Brake caliper bleeder | 8.5 ± 1.47 N·m | 75 in·lb | p. 259 |
| Brake pad pin | 10.1 ± 2.03 N·m | 89 in·lb | p. 261 |
| Master cylinder clamp | 9 ± 1 N·m | p. 264 | |
| Washers | 27 ± 1 N·m | p. 264 | |
| Middle clamp nut | 2.3 ± 0.23 N·m | 20 in·lb | p. 266 |
| Middle clamp nut | 35 ± 1 N·m | p. 266 | |
| Caliper Banjo fitting | 35.3 ± 1.36 N·m | 26 ft·lb | p. 266 |
| Master cylinder Banjo | 27 ± 1 N·m | p. 266 | |
| Caliper Banjo fitting | 27.1 ± 1.36 N·m | 20 ft·lb | p. 266 |
| Magnetic check plug | 6 ± 1 N·m | p. 269 | |
| Drain plug | 6 ± 1.02 N·m | 53 in·lb | p. 270 |
| Bearing | 24.5 ± 3.5 N·m | p. 276 | |
| Rear idler wheel | 48 ± 6 N·m | p. 285 | |
| Retaining screws | 47.5 ± 5.42 N·m | 35 ft·lb | p. 285 |
| Rear idler wheel | 24.5 ± 3.5 N·m | p. 285 | |
| Front shock absorber | 31.5 ± 3.5 N·m | p. 296 | |
| Retaining nuts | 31.2 ± 4.07 N·m | 23 ft·lb | p. 296 |
| Suspension | 3 ± 0.2 N·m | p. 306 | |
| Front and rear arm | 48 ± 6 N·m | p. 309 | |
| Upper bolts | 47.5 ± 5.42 N·m | 35 ft·lb | p. 309 |
| Rear shock absorber | 24.5 ± 3.5 N·m | p. 312 | |
| Center shock absorber | 40 ± 5 N·m | p. 313 | |
| Throttle rods upper nut | 36.6 ± 1.36 N·m | 27 ft·lb | p. 317 |
| Throttle rods upper nut | 24.5 ± 3.5 N·m | p. 317 | |
| Jam nut | 18.5 ± 3.5 N·m | 164 in·lb | p. 326 |
| Runner nut | 8 ± 1.02 N·m | 71 in·lb | p. 327 |
| Ski nut | 47.5 ± 5.42 N·m | 35 ft·lb | p. 328 |
| Adjusting knob screw | 9 ± 1.02 N·m | 80 in·lb | p. 331 |
| Adjusting knob screw | 24.5 ± 3.5 N·m | p. 331 | |
| Indicator screw | 24.4 ± 4.07 N·m | 18 ft·lb | p. 331 |
| Extension nuts | 3 ± 0.5 N·m | p. 333 | |
| Extension nuts | 3.1 ± 0.45 N·m | 27 in·lb | p. 333 |
| Multifunction switch | 2.4 ± 0.2 N·m | p. 335 | |
| Throttle lever retaining | 1.5 ± 0.2 N·m | p. 337 | |
| Throttle lever pivot | 1.5 ± 0.2 N·m | p. 338 | |
| Clamp screws | 24.4 ± 4.07 N·m | 18 ft·lb | p. 339 |
| Outer tie-rod end nut | 48 ± 6 N·m | p. 342 | |
| Outer tie-rod end nut | 24.5 ± 3.5 N·m | p. 342 | |
| Inner tie-rod end nut | 24.4 ± 4.07 N·m | 18 ft·lb | p. 342 |
| Upper steering column | 12.5 ± 2.5 N·m | p. 344 | |
| Support nut | 12.5 ± 2.49 N·m | 111 in·lb | p. 344 |
| Lower steering column | 23.5 ± 3.5 N·m | p. 344 | |
| Support nut | 23 ± 4.07 N·m | 17 ft·lb | p. 344 |
| Housing screw | 2.3 ± 0.23 N·m | 20 in·lb | p. 350 |
| Gauge support screw | 2.3 ± 0.23 N·m | 20 in·lb | p. 352 |
| Hood hexagonal screw | 1.8 ± 0.23 N·m | 16 in·lb | p. 354 |
| Hood hexagonal screw | 2.3 ± 0.2 N·m | p. 354 | |
| Hood Torx screw | 2.3 ± 0.02 N·m | 20 in·lb | p. 354 |
| Headlight Torx screw | 2.3 ± 0.23 N·m | 20 in·lb | p. 354 |
| Console nut | 2.3 ± 0.23 N·m | 20 in·lb | p. 355 |
| Front bumper nut | 5 ± 0.45 N·m | 44 in·lb | p. 356 |
| Bottom pan screw | 1.8 ± 0.23 N·m | 16 in·lb | p. 357 |
| Side bottom pan screw | 2.8 ± 0.23 N·m | 25 in·lb | p. 358 |
| Rear bumper screws | 16 ± 2.03 N·m | 142 in·lb | p. 359 |
Bakım aralıkları
Dosyanın tamamı bot tarafından gönderilir.
| Kalem | Değer | Ayrıca | PDF sayfası |
|---|---|---|---|
| Drive chain service | 500 km | p. 27 | |
| Coolant change | 5 years | p. 28 |
Belgeyi edin
Dosyanın tamamı bot tarafından gönderilir.
Telegram'da aç — bot bu belgeyi katalog kimliğiyle bulur ve dosyayı gönderir.
Botta aç- Parça kataloğuTüm kılavuzlar