AODES Desertcross 2024 Werkstatthandbuch
AODES Desertcross · 2024 · Werkstatthandbuch · 249 Seiten
Technische Daten
Die vollständige Datei wird vom Bot geliefert.
Anzugsdrehmoment
Die vollständige Datei wird vom Bot geliefert.
| Artikel | Wert | Passt auch | PDF-Seite |
|---|---|---|---|
| Fastening nut of front differential | 80 N·m | 59 ft·lb | p. 9 |
| Water temperature sensor | 16 N·m | 11.8 ft·lb | p. 9 |
| Adjusting nut of valve clearance | 12 N·m | 8.9 ft·lb | p. 9 |
| Main pulley bolt | 100 N·m | 73.8 ft·lb | p. 9 |
| Magneto stator bolt | 12.5 N·m | 9.2 ft·lb | p. 9 |
| Drain plug | 30 N·m | 22 ft·lb | p. 20 |
| Drain plug | 20 N·m | 14.76 ft·lb | p. 22 |
| Oil level check plug | 20 N·m | 14.76 ft·lb | p. 22 |
| Reed valve reating | 10 ± 1 N·m | p. 38 | |
| Water pump housing | 10 ± 1 N·m | p. 42 | |
| Holding strip screws | 4 ± 0.34 N·m | 35 in·lb | p. 57 |
| Sprag clutch housing | 30 ± 2 N·m | p. 59 | |
| Valve cover screws | 7 ± 0.8 N·m | p. 66 | |
| Valve cover screws | 0.8 N·m | 7 in·lb | p. 66 |
| M6 cylinder head | 10 ± 1 N·m | p. 73 | |
| Chain tensioner plug | 4.5 ± 0.45 N·m | 40 in·lb | p. 88 |
| Timing chain guide | 1 N·m | p. 95 | |
| Bearing screw | 10.1 ± 1.02 N·m | 89 in·lb | p. 95 |
| Rear bearing cover | 1 N·m | p. 101 | |
| Front bearing cover | 1 N·m | p. 101 | |
| PTO cover screws | 1 N·m | 9 in·lb | p. 106 |
| M8 crankcase screws | 25 ± 3 N·m | p. 111 | |
| M8 crankcase screws | 24.4 ± 2.71 N·m | 18 ft·lb | p. 111 |
| M6 crankcase screws | 10 ± 1 N·m | p. 111 | |
| Components except drive pulley hub | 2 ± 0.2 N·m | p. 120 | |
| Bayonet cap | 2 ± 0.23 N·m | 18 in·lb | p. 120 |
| CVT cover | 6 ± 0.7 N·m | p. 121 | |
| Drive pulley screw | 120.7 ± 8.13 N·m | 89 ft·lb | p. 123 |
| VSS retaining screw | 10.1 ± 1.02 N·m | 89 in·lb | p. 130 |
| Differential locking | 3 ± 0.2 N·m | p. 134 | |
| PIN actuator retaining | 36.6 ± 2.71 N·m | 27 ft·lb | p. 134 |
| Plug screws | 29.8 ± 2.71 N·m | 22 ft·lb | p. 134 |
| Tighen gearbox retaining nuts | 25 ± 3 N·m | p. 137 | |
| Gearbox retaining nuts | 24.4 ± 2.71 N·m | 18 ft·lb | p. 137 |
| Retaining plate screws | 120.7 ± 12.2 N·m | 89 ft·lb | p. 140 |
| Retaining screws main | 10 ± 1 N·m | p. 140 | |
| Shaft bearing | 120.7 ± 12.2 N·m | 89 ft·lb | p. 140 |
| Parking lock gear | 170 ± 10 N·m | p. 142 | |
| Countershaft nut | 169.5 ± 9.49 N·m | 125 ft·lb | p. 142 |
| Main shaft | 120.7 N·m | 89 ft·lb | p. 142 |
| Bearing housing | 10 ± 1 N·m | p. 143 | |
| Index washer | 10 ± 1 N·m | p. 151 | |
| Index lever retaining | 10 ± 1 N·m | p. 151 | |
| Park locking gear | 170 ± 10 N·m | p. 151 | |
| Coupling Mechanism | 10 ± 1 N·m | p. 152 | |
| Gearbox cover screws Output Shaft | 120.7 ± 12.2 N·m | 89 ft·lb | p. 152 |
| Rear differential | 8 ± 1 N·m | p. 153 | |
| Bolt of front propeller shaft flange | 40 N·m | 4.1 kgf·m | p. 165 |
| Bolt of front propeller shaft flange | 80 N·m | 8.2 kgf·m | p. 165 |
| Ball joint retaining bolts | 45 N·m | p. 168 | |
| Mounting nut of wheel rim | 60 N·m | 6.1 kgf·m | p. 169 |
| Nut of wheel hub | 300 N·m | 30.6 kgf·m | p. 169 |
| Bolt of PARK brake caliper | 80 N·m | 8.2 kgf·m | p. 172 |
| Exhaust Valve Locking | 6 N·m | p. 188 | |
| Parameters of electromagnetic clutch | 23 N·m | p. 196 |
Füllmengen
Die vollständige Datei wird vom Bot geliefert.
| Artikel | Wert | Passt auch | PDF-Seite |
|---|---|---|---|
| Fuel tank | 50.3 L | p. 5 |
Zündkerzen
Die vollständige Datei wird vom Bot geliefert.
| Artikel | Wert | Passt auch | PDF-Seite |
|---|---|---|---|
| M22 | — | p. 9 | |
| Spark plug | 0.7–0.9 mm | p. 17 | |
| HD8 | — | p. 70 | |
| M10 | — | p. 71 |
Wartungsintervalle
Die vollständige Datei wird vom Bot geliefert.
| Artikel | Wert | Passt auch | PDF-Seite |
|---|---|---|---|
| Coolant change | 24 months | p. 11 | |
| Air filter service | 24 months | p. 11 | |
| Drive belt service | 24 months | p. 12 |
Dokument beziehen
Die vollständige Datei wird vom Bot geliefert.
In Telegram öffnen — der Bot findet dieses Dokument anhand seiner Katalog-ID und sendet die Datei.
Im Bot öffnen- TeilekatalogAlle Handbücher