BRP 2023 Werkstatthandbuch
BRP · 2023 · Werkstatthandbuch · 1875 Seiten
Technische Daten
Die vollständige Datei wird vom Bot geliefert.
Anzugsdrehmoment
Die vollständige Datei wird vom Bot geliefert.
| Artikel | Wert | Passt auch | PDF-Seite |
|---|---|---|---|
| Intake Manifold | 6 ± 0.7 N·m | p. 77 | |
| Air filter housing clamp | 2.5 ± 0.45 N·m | 22 in·lb | p. 79 |
| Intake socket screws | 7 ± 0.79 N·m | 62 in·lb | p. 79 |
| MAPTS Temperature Sensor Test Results | 6 ± 6 N·m | 53 in·lb | p. 81 |
| Air Intake System | 2.5 ± 0.5 N·m | p. 82 | |
| Air filter housing | 10 ± 2 N·m | p. 84 | |
| Tail pipe retaining | 32.5 ± 1.36 N·m | 24 ft·lb | p. 87 |
| Heat shield screw | 13.4 ± 1.47 N·m | 119 in·lb | p. 89 |
| Exhaust pipe clamp | 58.3 ± 1.36 N·m | 43 ft·lb | p. 89 |
| Gear clamp | 8 ± 0.5 N·m | p. 91 | |
| Drain plug | 30 ± 2 N·m | p. 99 | |
| Oil filter cover | 10 ± 1 N·m | p. 100 | |
| Oil strainer screws | 6 ± 0.68 N·m | 53 in·lb | p. 105 |
| Reed valve retaining | 10 ± 1 N·m | p. 106 | |
| Water pump housing | 10 ± 1 N·m | p. 110 | |
| Coolant drain plug | 10.1 ± 1.02 N·m | 89 in·lb | p. 127 |
| Magneto and Starter | 6 ± 0.7 N·m | p. 136 | |
| Magneto cover screws | 10 ± 1 N·m | p. 138 | |
| Holding strip screws | 4 ± 0.34 N·m | 35 in·lb | p. 140 |
| Holding strip screws | 10 ± 1 N·m | p. 140 | |
| Stator retaining screws | 10.1 ± 1.02 N·m | 89 in·lb | p. 140 |
| Rotor retaining screw | 150.5 ± 9.49 N·m | 111 ft·lb | p. 142 |
| Starter cable nut | 6 ± 0.68 N·m | 53 in·lb | p. 145 |
| Cylinder Head | 7 ± 0.8 N·m | p. 148 | |
| Knock sensor | 20 ± 3 N·m | p. 155 | |
| Age of internal engine components | 7 ± 0.8 N·m | p. 155 | |
| M6 Cylinder head | 10 ± 1 N·m | p. 161 | |
| M10 Cylinder | 20.3 ± 1.36 N·m | 15 ft·lb | p. 161 |
| Camshaft timing gear | 10 ± 1 N·m | p. 179 | |
| Cylinder Block | 10 ± 1 N·m | p. 187 | |
| Rear bearing cover | 10 ± 1 N·m | p. 191 | |
| M6 crankcase screws | 10.1 ± 1.02 N·m | 89 in·lb | p. 200 |
| Bayonet cap | 2 ± 0.23 N·m | 18 in·lb | p. 212 |
| CVT cover retaining | 6 ± 0.7 N·m | p. 213 | |
| Retaining screws | 20.3 ± 1.36 N·m | 15 ft·lb | p. 216 |
| NOTICE Centrifugal lever lock | 5 ± 1 N·m | p. 223 | |
| Drive pulley screw | 120.7 ± 8.13 N·m | 89 ft·lb | p. 225 |
| Locking screws | 3.5 ± 0.4 N·m | p. 229 | |
| Driven pulley screw | 70 ± 5 N·m | p. 230 | |
| Cam screw | 61 ± 5.42 N·m | 45 ft·lb | p. 230 |
| Hoses | 10 ± 1 N·m | p. 231 | |
| Gearbox | 8 ± 1 N·m | p. 235 | |
| Drain plug Vehicle Speed Sensor | 20.3 ± 1.36 N·m | 15 ft·lb | p. 238 |
| VSS retaining screw | 10.1 ± 1.02 N·m | 89 in·lb | p. 240 |
| WD indicator switch | 2 N·m | 18 in·lb | p. 242 |
| WD actuator screws | 10.1 ± 1.02 N·m | 89 in·lb | p. 243 |
| Differential locking | 3 ± 0.2 N·m | p. 245 | |
| Gearbox retaining nuts | 24.4 ± 2.71 N·m | 18 ft·lb | p. 248 |
| Main shaft bearing | 10 ± 1 N·m | p. 251 | |
| Retaining plate screw | 10 ± 1 N·m | p. 251 | |
| M6 gearbox housing | 10 ± 1 N·m | p. 252 | |
| M8 gearbox housing | 25 ± 3 N·m | p. 252 | |
| Parking lock gear | 170 ± 10 N·m | p. 253 | |
| Countershaft nut | 169.5 ± 9.49 N·m | 125 ft·lb | p. 253 |
| Main shaft | 170 ± 10 N·m | p. 253 | |
| Intermediate shaft nuts | 169.5 ± 9.49 N·m | 125 ft·lb | p. 253 |
| Bearing housing | 10 ± 1 N·m | p. 254 | |
| Index lever retaining | 10 ± 1 N·m | p. 260 | |
| Park locking gear nut | 170 ± 10 N·m | p. 261 | |
| Shift drum | 169.5 ± 9.49 N·m | 125 ft·lb | p. 261 |
| Index washer retaining | 10 ± 1 N·m | p. 261 | |
| Gearbox cover screws | 10.1 ± 1.02 N·m | 89 in·lb | p. 261 |
| Coupling fork shaft | 6 ± 0.7 N·m | p. 263 | |
| Shifter lever handle | 15.5 ± 1.5 N·m | p. 267 | |
| Shifter plate nut | 9 ± 1.02 N·m | 80 in·lb | p. 269 |
| ECM retaining screws | 2.5 ± 0.5 N·m | p. 275 | |
| Retaining nuts | 13 ± 1 N·m | p. 289 | |
| Accelerator pedal nuts | 13 ± 1.02 N·m | 115 in·lb | p. 289 |
| Tle plate and on bore | 10 ± 1 N·m | p. 296 | |
| Fuel Tank and Fuel Pump | 22.5 ± 2.5 N·m | p. 300 | |
| Fuel Tank and Fuel Pump | 23 ± 2.71 N·m | 17 ft·lb | p. 300 |
| Fuel tank retaining | 10 ± 2 N·m | p. 306 | |
| Bolts and nut | 10.1 ± 2.03 N·m | 89 in·lb | p. 306 |
| Fuel pump retaining | 60 ± 5 N·m | p. 309 | |
| Neck on fuel tank | 59.7 ± 5.42 N·m | 44 ft·lb | p. 309 |
| Pre-filter retaining | 6.5 ± 0.5 N·m | p. 314 | |
| Protects fuse rear box V-Twin engine | 9 ± 1 N·m | p. 321 | |
| Protects front fuse box | 9 ± 1.02 N·m | 80 in·lb | p. 321 |
| Ignition coil retaining | 10 ± 2 N·m | p. 339 | |
| Spark plug | 11 N·m | 97 in·lb | p. 341 |
| Battery holder | 7 ± 1 N·m | p. 347 | |
| Retaining screws | 7 ± 1.02 N·m | 62 in·lb | p. 347 |
| Battery post screw | 10.1 ± 2.03 N·m | 89 in·lb | p. 347 |
| Tailight/brake light unit | 7 ± 1 N·m | p. 354 | |
| Relay winding ground | 7 ± 1.02 N·m | 62 in·lb | p. 354 |
| Winch screws | 16 ± 2.03 N·m | 142 in·lb | p. 368 |
| Hexagonal screws | 17.5 ± 2.49 N·m | 155 in·lb | p. 368 |
| Skid plate retaining | 10 ± 2 N·m | p. 368 | |
| Winch cable nuts | 7 ± 0.45 N·m | 62 in·lb | p. 368 |
| Wheel lug nuts | 100.3 ± 9.49 N·m | 74 ft·lb | p. 371 |
| Beadlock screws | 29 ± 1 N·m | p. 372 | |
| Beadlock screws | 14 ± 1 N·m | p. 372 | |
| Brakes | 250 ± 15 N·m | p. 376 | |
| Castellated nut | 249.5 ± 14.91 N·m | 184 ft·lb | p. 376 |
| Propeller shaft nut | 31.2 ± 4.07 N·m | 23 ft·lb | p. 378 |
Zündkerzen
Die vollständige Datei wird vom Bot geliefert.
| Artikel | Wert | Passt auch | PDF-Seite |
|---|---|---|---|
| M10 | — | p. 159 | |
| HD9 | — | p. 1187 | |
| HD8 | — | p. 1187 | |
| G2L | — | p. 1188 | |
| HD10 | — | p. 1190 | |
| H11 | — | p. 1382 |
Wartungsintervalle
Die vollständige Datei wird vom Bot geliefert.
| Artikel | Wert | Passt auch | PDF-Seite |
|---|---|---|---|
| Spark plug service | 5 years | p. 56 | |
| Coolant change | 5 years | p. 1319 | |
| Brake inspection | 2 years | p. 1319 |
Dokument beziehen
Die vollständige Datei wird vom Bot geliefert.
In Telegram öffnen — der Bot findet dieses Dokument anhand seiner Katalog-ID und sendet die Datei.
Im Bot öffnen- Offizielle kostenlose BRP-BedienungsanleitungenTeilekatalogAlle Handbücher