BRP Outlander 2020 Werkstatthandbuch
BRP Outlander · 2020 · Werkstatthandbuch · 1585 Seiten
Technische Daten
Die vollständige Datei wird vom Bot geliefert.
Anzugsdrehmoment
Die vollständige Datei wird vom Bot geliefert.
| Artikel | Wert | Passt auch | PDF-Seite |
|---|---|---|---|
| Tail pipe retaining screws | 11 ± 1.02 N·m | 97 in·lb | p. 21 |
| Reservoir | 10 ± 1 N·m | p. 24 | |
| Oil filter cover screws | 10.1 ± 1.02 N·m | 89 in·lb | p. 24 |
| Coolant drain plug | 10.1 ± 1.02 N·m | 89 in·lb | p. 27 |
| Bleed screws | 5 ± 0.56 N·m | 44 in·lb | p. 27 |
| Indication of a gearbox problem | 20 ± 2 N·m | p. 29 | |
| Magnetic drain plug | 20 ± 2 N·m | p. 29 | |
| Oil level plug | 5 ± 0.56 N·m | 44 in·lb | p. 29 |
| Spark plug | 20.3 ± 1.36 N·m | 15 ft·lb | p. 33 |
| Spark plug | 11 ± 1.02 N·m | 97 in·lb | p. 33 |
| Filler plug | 22.5 ± 2.5 N·m | p. 33 | |
| Filler plug | 23 ± 2.71 N·m | 17 ft·lb | p. 33 |
| Drain plug | 7.5 ± 0.45 N·m | 66 in·lb | p. 35 |
| Wheel lug nuts | 80 ± 5 N·m | p. 35 | |
| Engine retaining bolts | 62.4 ± 8.13 N·m | 46 ft·lb | p. 54 |
| Suspension | 6 N·m | p. 65 | |
| Head pipe nuts | 13 ± 1 N·m | p. 72 | |
| Rear cylinder | 13 ± 1.02 N·m | 115 in·lb | p. 72 |
| Exhaust pipe clamp | 40.7 ± 1.36 N·m | 30 ft·lb | p. 76 |
| Oil Strainer screws | 6 ± 0.7 N·m | p. 91 | |
| Thermostat cover | 6 ± 0.7 N·m | p. 108 | |
| Retaining screws | 6 ± 0.68 N·m | 53 in·lb | p. 108 |
| Water pump impeller | 2.5 ± 0.34 N·m | 22 in·lb | p. 109 |
| Water pump housing | 10 ± 1 N·m | p. 109 | |
| Radiator upper retaining | 10 ± 2 N·m | p. 136 | |
| Regulator/rectifier (P/N 529 035 868) | 10.1 ± 1.02 N·m | 89 in·lb | p. 142 |
| Holding strip screws | 4 ± 0.45 N·m | 35 in·lb | p. 144 |
| Stator retaining screws | 10.1 ± 1.02 N·m | 89 in·lb | p. 144 |
| Rotor retaining screw | 150.5 ± 9.49 N·m | 111 ft·lb | p. 145 |
| Sprag clutch housing | 30 ± 2 N·m | p. 147 | |
| Starter mounting screw | 25 ± 3 N·m | p. 149 | |
| Retaining nut | 6 ± 0.45 N·m | 53 in·lb | p. 149 |
| CESS. Starter mounting screw | 24.4 ± 2.71 N·m | 18 ft·lb | p. 160 |
| CVT back cover | 6 ± 0.5 N·m | p. 160 | |
| Intake manifold | 20 ± 2 N·m | p. 163 | |
| Retaining screws | 20.3 ± 1.36 N·m | 15 ft·lb | p. 163 |
| Intake socket clamp | 0.7 ± 0.1 N·m | p. 166 | |
| Valve cover retaining | 7 ± 0.8 N·m | p. 176 | |
| M6 cylinder head | 10 ± 1 N·m | p. 183 | |
| M10 x 140 screws | 10.1 ± 1.02 N·m | 89 in·lb | p. 183 |
| Camshaft timing gear | 10 ± 1 N·m | p. 255 | |
| Timing chain guide | 10 ± 1 N·m | p. 260 | |
| Bearing screw | 10.1 ± 1.02 N·m | 89 in·lb | p. 260 |
| Rear bearing cover | 10 ± 1 N·m | p. 277 | |
| Front bearing cover | 10 ± 1 N·m | p. 278 | |
| PTO cover screws | 10 ± 1 N·m | p. 282 | |
| 570, 650 and 850 Engines screws | 29.8 ± 1.36 N·m | 22 ft·lb | p. 294 |
| Drive pulley screw | 120.7 ± 8.13 N·m | 89 ft·lb | p. 332 |
| Gearbox | 10.1 ± 1.02 N·m | 89 in·lb | p. 344 |
| CVT cover screws | 7 ± 1.02 N·m | 62 in·lb | p. 371 |
| CVT hose clamps | 2.5 ± 0.45 N·m | 22 in·lb | p. 371 |
| Lock nuts | 8 ± 1 N·m | p. 380 | |
| Threaded stud | 50 ± 2 N·m | p. 382 | |
| Drive pulley nut | 80 ± 1 N·m | p. 382 | |
| REQUIRED TOOL Stud | 44.7 ± 1.36 N·m | 33 ft·lb | p. 390 |
| Counter nut | 35.3 ± 1.36 N·m | 26 ft·lb | p. 393 |
| PIN B PIN C between battery | 10 ± 1 N·m | p. 400 | |
| VSS retaining screw | 10.1 ± 1.02 N·m | 89 in·lb | p. 400 |
| Actuator screws | 24.4 ± 2.71 N·m | 18 ft·lb | p. 404 |
| Right housing | 24.4 ± 2.71 N·m | 18 ft·lb | p. 411 |
| Right housing | 10 ± 1 N·m | p. 411 | |
| Gear housing | 10 ± 1 N·m | p. 427 | |
| O-ring | 25 ± 3 N·m | p. 438 | |
| Shaft CVT side | 25 ± 3 N·m | p. 521 | |
| Shaft CVT side | 24.4 ± 2.71 N·m | 18 ft·lb | p. 521 |
| Gearbox retaining nuts | 24.4 ± 2.71 N·m | 18 ft·lb | p. 522 |
| Shift plate nut | 9 ± 1 N·m | p. 554 | |
| TAS housing retaining | 3.5 ± 0.5 N·m | p. 604 | |
| ECM screws | 2 ± 0.23 N·m | 18 in·lb | p. 609 |
| Fuel rail retaining screws | 10.1 ± 1.02 N·m | 89 in·lb | p. 614 |
| Throttle body retaining | 10 ± 1.2 N·m | p. 615 | |
| CPS retaining screw | 10.1 ± 1.02 N·m | 89 in·lb | p. 617 |
| Constant low voltage sensor fault | 16 ± 2 N·m | p. 621 | |
| ECM screws | 6.6 ± 0.45 N·m | 58 in·lb | p. 628 |
| Throttle plate edge | 10 ± 1 N·m | p. 632 | |
| Throttle body retaining | 7.5 ± 0.5 N·m | p. 633 | |
| MAPTS retaining screw | 6 ± 0.7 N·m | p. 638 | |
| Oxygen sensor circuit | 16 ± 2 N·m | p. 639 | |
| Knock sensor mounting | 20 ± 3 N·m | p. 642 | |
| Fuel tank retaining | 6.5 ± 0.5 N·m | p. 672 | |
| Fuel pump retaining nut | 28.5 ± 1.36 N·m | 21 ft·lb | p. 675 |
| Ignition coil retaining bolt | 8 ± 1 N·m | p. 701 | |
| Battery retaining plate | 4.5 ± 0.5 N·m | p. 713 | |
| Retaining screws | 0.9 ± 0.11 N·m | 8 in·lb | p. 748 |
| Air intake tube retaining | 1.6 ± 0.4 N·m | p. 753 | |
| Clamping screw | 4.5 ± 0.45 N·m | 40 in·lb | p. 754 |
| Clamping screw | 0.4 ± 0.1 N·m | p. 754 | |
| Handlebar tip screw | 0.5 ± 0.11 N·m | 4 in·lb | p. 754 |
| Winch retaining screws | 16 ± 2.03 N·m | 142 in·lb | p. 759 |
| Winch retaining screws | 7 ± 5 N·m | p. 759 | |
| Winch power cables nuts | 16 ± 2.03 N·m | 142 in·lb | p. 759 |
| Beadlock screws | 25 ± 1 N·m | p. 761 | |
| Beadlock screws | 14 ± 1 N·m | p. 761 | |
| Castellated nut | 205 ± 15 N·m | p. 768 | |
| Visco-Lok / ring gear | 37 ± 3 N·m | p. 775 | |
| Differential housing | 23.5 ± 3.5 N·m | p. 775 |
Füllmengen
Die vollständige Datei wird vom Bot geliefert.
| Artikel | Wert | Passt auch | PDF-Seite |
|---|---|---|---|
| Fuel tank | 20.5 L | p. 942 |
Zündkerzen
Die vollständige Datei wird vom Bot geliefert.
| Artikel | Wert | Passt auch | PDF-Seite |
|---|---|---|---|
| M10 | — | p. 181 |
Wartungsintervalle
Die vollständige Datei wird vom Bot geliefert.
| Artikel | Wert | Passt auch | PDF-Seite |
|---|---|---|---|
| Brake inspection | 2 years | p. 16 |
Dokument beziehen
Die vollständige Datei wird vom Bot geliefert.
In Telegram öffnen — der Bot findet dieses Dokument anhand seiner Katalog-ID und sendet die Datei.
Im Bot öffnen- Offizielle kostenlose BRP-BedienungsanleitungenTeilekatalogAlle Handbücher