Ski-Doo RTX23 E TEC Handbuch
Ski-Doo RTX23 E TEC · Handbuch · 258 Seiten
Technische Daten
Die vollständige Datei wird vom Bot geliefert.
Anzugsdrehmoment
Die vollständige Datei wird vom Bot geliefert.
| Artikel | Wert | Passt auch | PDF-Seite |
|---|---|---|---|
| Exhaust manifold | 34 ± 4 N·m | p. 23 | |
| Procedures screws | 33.9 ± 4.07 N·m | 25 ft·lb | p. 25 |
| Bearing screw | 8 ± 0.45 N·m | 71 in·lb | p. 33 |
| Retaining screws | 9 ± 0.56 N·m | 80 in·lb | p. 34 |
| Water pump cover | 11 ± 0.8 N·m | p. 59 | |
| Coolant hose clamp | 5.5 ± 0.45 N·m | 49 in·lb | p. 60 |
| Bearing carrier screws | 5 ± 0.34 N·m | 44 in·lb | p. 64 |
| Taptite screws | 6 ± 0.68 N·m | 53 in·lb | p. 64 |
| Magneto and Starter | 11 ± 0.8 N·m | p. 68 | |
| Magneto flywheel | 125 ± 9 N·m | p. 74 | |
| Retaining screw | 124.7 ± 9.49 N·m | 92 ft·lb | p. 74 |
| Magneto housing | 7 ± 0.5 N·m | p. 75 | |
| Stator retaining screws | 10.1 ± 0.68 N·m | 89 in·lb | p. 77 |
| Retaining screws | 8 ± 0.45 N·m | 71 in·lb | p. 91 |
| RAVE valve housing | 10 ± 0.7 N·m | p. 96 | |
| Collar nuts | 4 ± 0.34 N·m | 35 in·lb | p. 96 |
| RAVE cable lock nut | 20.3 ± 1.36 N·m | 15 ft·lb | p. 98 |
| Rave cable lock nut | 5 ± 0.56 N·m | 44 in·lb | p. 98 |
| Pin | 20 ± 2 N·m | p. 98 | |
| Bracket retaining | 11 ± 0.8 N·m | p. 100 | |
| Reed valve blade | 1.5 ± 0.3 N·m | p. 105 | |
| Intake adapter | 6 ± 0.4 N·m | p. 105 | |
| Cylinder Head | 6 ± 0.45 N·m | 53 in·lb | p. 105 |
| Cylinder Head Warpage Cylinder head | 7 ± 0.2 N·m | p. 107 | |
| Cylinder block screws Cylinder Block Base Gaske | 50 ± 1.5 N·m | p. 111 | |
| Cylinder block screws Cylinder Block Base Gasket | 50.2 ± 1.36 N·m | 37 ft·lb | p. 111 |
| Retaining screws | 6 ± 0.45 N·m | 53 in·lb | p. 122 |
| M8 Crankcase screws | 29.8 ± 1.36 N·m | 22 ft·lb | p. 139 |
| M6 Crankcase screws | 11 ± 0.79 N·m | 97 in·lb | p. 139 |
| Oil seal cover screws | 11 ± 0.79 N·m | 97 in·lb | p. 140 |
| Crankshaft for procedure | 30 ± 2 N·m | p. 153 | |
| MAG side RAVE valve | 6 ± 0.7 N·m | p. 166 | |
| Retaining screw | 5 ± 0.34 N·m | 44 in·lb | p. 171 |
| Oil catch tank screw | 7.5 ± 1.02 N·m | 66 in·lb | p. 173 |
| Oil pump screw | 1.8 ± 0.23 N·m | 16 in·lb | p. 174 |
| Opened 0.4 V - 0.7 V screw | 24.4 ± 4.07 N·m | 18 ft·lb | p. 177 |
| Retaining screws | 11 ± 0.79 N·m | 97 in·lb | p. 180 |
| Fuel hose retainer | 5 N·m | p. 211 | |
| Otherwise, throttle body may have | 8 ± 0.5 N·m | p. 216 | |
| Throttle body clamps | 1.5 ± 0.23 N·m | 13 in·lb | p. 218 |
| Adapter plate clamps | 0.7 ± 0.11 N·m | 6 in·lb | p. 218 |
| TPS retaining screw | 4 ± 0.45 N·m | 35 in·lb | p. 220 |
| Spark plug | 23 ± 1 N·m | p. 229 | |
| Ignition coil retaining | 2.4 ± 0.2 N·m | p. 232 | |
| Ground cable screw | 8 ± 0.45 N·m | 71 in·lb | p. 238 |
| Knock sensor screw | 24.4 ± 1.36 N·m | 18 ft·lb | p. 240 |
Dokument beziehen
Die vollständige Datei wird vom Bot geliefert.
In Telegram öffnen — der Bot findet dieses Dokument anhand seiner Katalog-ID und sendet die Datei.
Im Bot öffnen- TeilekatalogAlle Handbücher