Ski-Doo Skandic 2015 Werkstatthandbuch
Ski-Doo Skandic · 2015 · Werkstatthandbuch · 1561 Seiten
Technische Daten
Die vollständige Datei wird vom Bot geliefert.
Anzugsdrehmoment
Die vollständige Datei wird vom Bot geliefert.
| Artikel | Wert | Passt auch | PDF-Seite |
|---|---|---|---|
| Water pump | 9 ± 1 N·m | p. 29 | |
| Drain plug I | 10 N·m | 89 in·lb | p. 30 |
| Oil Filter Cover | 9 ± 1 N·m | p. 34 | |
| Filter cover screw I | 3 N·m | 27 in·lb | p. 35 |
| Brake caliper bleeder I | 9 N·m | 80 in·lb | p. 38 |
| Bra ke caliper | 9 N·m | 80 in·lb | p. 38 |
| Pivot screw brake lever I | 6 N·m | 53 in·lb | p. 39 |
| Oil level check plug I | 10 N·m | 89 in·lb | p. 40 |
| Engine mounting | 24.5 ± 3.5 N·m | p. 55 | |
| Engine support screws I | 42 ± 4 N·m | p. 56 | |
| Rubber mount screws (MAG Side) | 24.4 ± 4.07 N·m | 18 ft·lb | p. 56 |
| Eng ine support screws I | 42 ± 4 N·m | 31 ft·lb | p. 57 |
| Rubber mount screws I | 10 ± 2 N·m | p. 58 | |
| Section 02 ENGINE | 9 ± 1 N·m | 80 in·lb | p. 68 |
| Lighten regulator plug | 17 ± 2 N·m | p. 79 | |
| Magneto cover | 9 ± 1 N·m | p. 98 | |
| Semble radiator w hen rem oved for access | 9 ± 1 N·m | p. 99 | |
| Rubber mount screw (MAG Side) | 24.4 ± 4.07 N·m | 18 ft·lb | p. 176 |
| Front and Rear Engine Rubber Mount | 24.5 ± 3.5 N·m | p. 177 | |
| Throttle body screws | 9 ± 1 N·m | p. 188 | |
| Circuit MAPTS RETAINING SCREW | 4.5 ± 0.5 N·m | p. 401 | |
| Engine Cut-Off Switch Continuity Test | 9 ± 1 N·m | p. 426 | |
| Off switch connector | 9 ± 1 N·m | p. 426 | |
| Pivot screws I | 20 N·m | 15 ft·lb | p. 470 |
| Cam screws I | 32 N·m | 24 ft·lb | p. 470 |
| Countershaft bearing area | 25 N·m | 18 ft·lb | p. 472 |
| Haft bearing area | 25 N·m | 18 ft·lb | p. 472 |
| Front of bearing support | 25 N·m | 18 ft·lb | p. 474 |
| Fra me member screw | 14 N·m | 124 in·lb | p. 474 |
| Suspension | 48 N·m | p. 477 | |
| Ski runner nuts | 8 N·m | 71 in·lb | p. 482 |
| Handlebar clamp screws | 25 N·m | 18 ft·lb | p. 484 |
| Expedition Models MOUNTING BOLT | 14 N·m | 124 in·lb | p. 491 |
| Tig hten emergency stop support retaining screws | 2 ± 0.2 N·m | p. 492 | |
| ITC housing retain | 9 ± 0.1 N·m | p. 492 | |
| Gearbox Oil CHECK PLUG | 10 ± 1 N·m | 89 in·lb | p. 798 |
| Lock nuts | 48 ± 6 N·m | p. 805 | |
| Oil filter | 10 ± 1 N·m | 89 in·lb | p. 913 |
| Coolant hose clamp I | 5.5 N·m | 49 in·lb | p. 916 |
| Gearbox drain plug I | 8 N·m | p. 926 | |
| Engine rubber mount | 5 ± 5 N·m | p. 944 | |
| Engine rubbe r mount | 5 ± 3.5 N·m | p. 945 | |
| Engine support screws I | 4 ± 3 N·m | p. 947 | |
| ENGINE RUBBER MOUNTS Engine rubber mount | 182 N·m | p. 947 | |
| Intake manifold screws I | 11 ± 1 N·m | p. 954 | |
| Exhaust fla nge screws | 1.4 N·m | 1 ft·lb | p. 957 |
| Exhaust flange screws I | 24 ± 2 N·m | p. 958 | |
| Exhaust pipes | 24.4 ± 1.36 N·m | 18 ft·lb | p. 958 |
| Oil pressure regulator plug | 29.8 ± 4.07 N·m | 22 ft·lb | p. 968 |
| Washers | 20 ± 2 N·m | p. 976 | |
| Oil drain plugs | 20 ± 1 N·m | p. 976 | |
| Coolant hose clamps I | 5.5 ± 0.5 N·m | p. 987 | |
| Retaining screws | 11 ± 1 N·m | p. 988 | |
| Magn eto cove r screws I | 11 ± 1 N·m | p. 995 | |
| Rotor retaining screw I | 150 ± 10 N·m | p. 998 | |
| Sprag clutch housing | 30 ± 2 N·m | p. 1000 | |
| Starter reta ining screws | 11 N·m | 97 in·lb | p. 1002 |
| Starter cable nut | 7 N·m | 62 in·lb | p. 1002 |
| Valve cover screws | 10.1 ± 1.02 N·m | 89 in·lb | p. 1025 |
| Fuel pump mounting nuts | 5 N·m | p. 1110 | |
| Carburetor mounting cl amps | 0.6 N·m | p. 1110 | |
| Throttle Body Synchronization | 1 ± 0.2 N·m | p. 1191 | |
| TPS retain ing screws I | 2 ± 0.4 N·m | p. 1195 | |
| Knock sensor screw | 29 N·m | p. 1205 | |
| ECM reta ining nuts I | 3.5 N·m | 31 in·lb | p. 1269 |
| Ignition co il retain ing screws I | 10 N·m | 89 in·lb | p. 1286 |
| Valve cover | 11 N·m | p. 1290 | |
| Primary Winding SPARK PLUGS | 11 N·m | 97 in·lb | p. 1290 |
| Voltage re.gulator/rectifier | 5 N·m | p. 1295 | |
| Battery retaining screws | 10 N·m | 89 in·lb | p. 1311 |
| Battery terminal screws | 3 N·m | 27 in·lb | p. 1311 |
| Voltage regulator screws | 5 N·m | p. 1318 | |
| Starter mounting screws | 28 N·m | 21 ft·lb | p. 1330 |
| Solenoid power cable terminals I | 4 N·m | 35 in·lb | p. 1332 |
| Hex screw | 28 N·m | 21 ft·lb | p. 1339 |
| Clamping screw I | 5.5 ± 0.5 N·m | p. 1383 | |
| Pivot nut I | 5 N·m | 44 in·lb | p. 1393 |
| Ring gear screw I | 27 N·m | 20 ft·lb | p. 1406 |
| Spring cover sc rews I | 25 N·m | 18 ft·lb | p. 1407 |
| Lever screws I | 10 N·m | 89 in·lb | p. 1408 |
| Washer | 10 N·m | 89 in·lb | p. 1409 |
| Washer | 120 N·m | 89 ft·lb | p. 1409 |
| Calibration screw nuts I | 10 N·m | 89 in·lb | p. 1410 |
| Pivot screws I | 6.8 N·m | 5 ft·lb | p. 1420 |
| Cam screws | 32 N·m | 24 ft·lb | p. 1420 |
| Countershaft bearing | 24.4 N·m | 18 ft·lb | p. 1422 |
| Front rubber mount bolt I | 25 N·m | 18 ft·lb | p. 1424 |
| Frame member bolt | 14 N·m | 124 in·lb | p. 1424 |
| Top of bearing support | 10.1 N·m | 89 in·lb | p. 1438 |
| Brake pad pin I | 10 N·m | 89 in·lb | p. 1442 |
| Caliper retaining screw I | 25 N·m | 18 ft·lb | p. 1446 |
| Washers | 35 N·m | 26 ft·lb | p. 1446 |
| Brake lever nut I | 6 N·m | 53 in·lb | p. 1448 |
| Speed sensor | 8 N·m | 71 in·lb | p. 1450 |
Füllmengen
Die vollständige Datei wird vom Bot geliefert.
| Artikel | Wert | Passt auch | PDF-Seite |
|---|---|---|---|
| Fuel tank | 45 L | p. 502 | |
| Engine oil | 3.7 L | p. 822 | |
| Engine oil | 2.8 L | p. 823 | |
| Fuel tank | 40 L | p. 1530 |
Zündkerzen
Die vollständige Datei wird vom Bot geliefert.
| Artikel | Wert | Passt auch | PDF-Seite |
|---|---|---|---|
| M14 | — | p. 153 | |
| BR9ECS | — | p. 827 | |
| CR7EB | — | p. 829 | |
| TP88 | — | p. 1299 |
Wartungsintervalle
Die vollständige Datei wird vom Bot geliefert.
| Artikel | Wert | Passt auch | PDF-Seite |
|---|---|---|---|
| Coolant change | 5 years | p. 26 |
Dokument beziehen
Die vollständige Datei wird vom Bot geliefert.
In Telegram öffnen — der Bot findet dieses Dokument anhand seiner Katalog-ID und sendet die Datei.
Im Bot öffnen- TeilekatalogAlle Handbücher