Ski-Doo Summit 2021 Werkstatthandbuch
Ski-Doo Summit · 2021 · Werkstatthandbuch · 1084 Seiten
Technische Daten
Die vollständige Datei wird vom Bot geliefert.
Anzugsdrehmoment
Die vollständige Datei wird vom Bot geliefert.
| Artikel | Wert | Passt auch | PDF-Seite |
|---|---|---|---|
| Coolant hose clamp | 3.1 ± 0.45 N·m | 27 in·lb | p. 20 |
| Spark plug | 18 ± 0.68 N·m | 159 in·lb | p. 23 |
| Rear idler wheel | 47.5 ± 5.42 N·m | 35 ft·lb | p. 26 |
| Brake caliper bleeder | 8.5 ± 1.47 N·m | 75 in·lb | p. 28 |
| INTAKE SYSTEM subsection | 31.2 ± 4.07 N·m | 23 ft·lb | p. 42 |
| Snug all bolts | 33 ± 3 N·m | p. 42 | |
| M5 Torx screw | 1.8 ± 0.2 N·m | p. 65 | |
| 219101031-002-016 panel nut | 1.8 ± 0.23 N·m | 16 in·lb | p. 65 |
| Muffler retaining screw | 7 ± 1.02 N·m | 62 in·lb | p. 70 |
| Exhaust Gas | 45 ± 2 N·m | p. 75 | |
| Temperature Sensor | 44.7 ± 1.36 N·m | 33 ft·lb | p. 75 |
| Exhaust pipe | 28 ± 1 N·m | p. 80 | |
| Oetiker clamp | 1.7 ± 0.2 N·m | p. 83 | |
| ETS retaining screw | 1.7 ± 0.23 N·m | 15 in·lb | p. 83 |
| Exhaust manifold screws | 33.9 ± 4.07 N·m | 25 ft·lb | p. 86 |
| Transmission | 15 ± 1 N·m | p. 117 | |
| Cylinder | 5.5 ± 0.5 N·m | p. 118 | |
| Head | 5.5 ± 0.45 N·m | 49 in·lb | p. 118 |
| Water pump cover screws | 11 ± 0.79 N·m | 97 in·lb | p. 123 |
| Bearing carrier screws | 5 ± 0.34 N·m | 44 in·lb | p. 127 |
| Retaining screw | 125 ± 9 N·m | p. 153 | |
| Magneto housing | 7 ± 0.5 N·m | p. 154 | |
| CPS retaining screws | 8 ± 0.45 N·m | 71 in·lb | p. 155 |
| Starter mounting screws | 11 ± 0.79 N·m | 97 in·lb | p. 160 |
| Retaining nut | 4 ± 0.3 N·m | p. 173 | |
| RAVE valve housing | 10 ± 0.7 N·m | p. 177 | |
| Collar nuts | 4 ± 0.34 N·m | 35 in·lb | p. 178 |
| Bracket | 20 ± 2 N·m | p. 179 | |
| RAVE cable lock nut | 20.3 ± 1.36 N·m | 15 ft·lb | p. 179 |
| Counter nut | 20 ± 2 N·m | p. 179 | |
| Snap ring | 20.3 ± 1.36 N·m | 15 ft·lb | p. 179 |
| RAVE cable lock nut | 5 ± 0.6 N·m | p. 179 | |
| Retaining plate screw | 5 ± 0.56 N·m | 44 in·lb | p. 179 |
| Bracket retaining screws | 11 ± 0.8 N·m | p. 181 | |
| Reed valve blade screws | 1.5 ± 0.34 N·m | 13 in·lb | p. 185 |
| Intake adapter retaining | 1.5 ± 0.3 N·m | p. 185 | |
| Intake adapter retaining | 6 ± 0.4 N·m | p. 185 | |
| Cylinder head screws | 30 ± 2 N·m | p. 188 | |
| Under screw head | 50 ± 1.5 N·m | p. 191 | |
| SERVICE PRODUCT Cylinder block screws | 50.2 ± 1.36 N·m | 37 ft·lb | p. 191 |
| Reed valve blade screws | 6 ± 0.45 N·m | 53 in·lb | p. 202 |
| Cylinder head screws | 28 ± 1 N·m | p. 205 | |
| Crankcase screws | 30 ± 2 N·m | p. 219 | |
| Oil seal cover screws | 11 ± 0.79 N·m | 97 in·lb | p. 220 |
| M8 Crankcase screws | 28.5 ± 1.36 N·m | 21 ft·lb | p. 233 |
| Oil catch tank screw | 7.5 ± 1.02 N·m | 66 in·lb | p. 253 |
| Oil pump screw | 1.8 ± 0.23 N·m | 16 in·lb | p. 254 |
| Retaining screws | 24.4 ± 1.36 N·m | 18 ft·lb | p. 260 |
| Tridon clamp | 1.7 ± 0.23 N·m | 15 in·lb | p. 303 |
| Fuel hose retainer screw | 5 N·m | 44 in·lb | p. 332 |
| Tainer screw | 5 N·m | 44 in·lb | p. 332 |
| Fuel rail retaining screws | 8 ± 0.45 N·m | 71 in·lb | p. 337 |
| Adapter plate clamps | 0.7 ± 0.1 N·m | p. 343 | |
| Throttle body clamps | 1.5 ± 0.23 N·m | 13 in·lb | p. 343 |
| TPS retaining screw | 4 ± 0.45 N·m | 35 in·lb | p. 345 |
| MAPTS retaining screw | 4.5 ± 0.5 N·m | p. 348 | |
| M6 screw on chassis | 10 ± 2 N·m | p. 355 | |
| Spark plug | 17.5 ± 1.02 N·m | 155 in·lb | p. 380 |
| Ignition coil retaining | 2.4 ± 0.2 N·m | p. 383 | |
| Battery terminals | 10 ± 2 N·m | p. 387 | |
| Battery hold down | 5 ± 0.5 N·m | p. 387 | |
| Bracket | 5 ± 0.45 N·m | 44 in·lb | p. 387 |
| Battery cover retaining | 7 ± 1 N·m | p. 387 | |
| Solenoid cable retaining | 4 ± 0.5 N·m | p. 398 | |
| Absolute CPS screws | 2.5 ± 0.3 N·m | p. 406 | |
| MAGNETO AND STARTER subsections | 5 ± 0.5 N·m | p. 409 | |
| Retaining nuts | 5 ± 0.45 N·m | 44 in·lb | p. 409 |
| Ground cable screw | 8 ± 0.45 N·m | 71 in·lb | p. 417 |
| Knock sensor screw | 24 ± 1 N·m | p. 419 | |
| Taillight retaining screw | 0.8 ± 0.23 N·m | 7 in·lb | p. 437 |
| Retaining screws | 1 ± 0.23 N·m | 9 in·lb | p. 441 |
| Torx screw | 7.5 ± 1.02 N·m | 66 in·lb | p. 453 |
| Elastic nut | 10.1 ± 2.03 N·m | 89 in·lb | p. 453 |
| Clamping screw | 5.5 ± 0.45 N·m | 49 in·lb | p. 455 |
| Drive belt guard support | 7.5 ± 1 N·m | p. 460 | |
| Roller axle screw | 5 ± 0.5 N·m | p. 473 | |
| Drive pulley bolt | 120 N·m | p. 475 | |
| Drive pulley bolt First | 120.7 N·m | 89 ft·lb | p. 475 |
| Damper screws | 31.2 ± 4.07 N·m | 23 ft·lb | p. 475 |
| Bearing flange nut | 15.5 ± 1.47 N·m | 137 in·lb | p. 484 |
| Brake synthetic | 10 ± 2 N·m | p. 487 | |
| Caliper screws | 24.5 ± 3.5 N·m | p. 493 | |
| Washers | 35 ± 1 N·m | p. 493 | |
| Brake lever pivot nut | 6 ± 1.02 N·m | 53 in·lb | p. 494 |
| Master cylinder clamp | 9 ± 1 N·m | p. 494 | |
| Washers | 27 ± 1 N·m | p. 494 | |
| Middle clamp nut | 2.3 ± 0.23 N·m | 20 in·lb | p. 496 |
| Middle clamp nut | 35 ± 1 N·m | p. 496 | |
| Caliper Banjo fitting | 35.3 ± 1.36 N·m | 26 ft·lb | p. 496 |
| Master cylinder Banjo | 27 ± 1 N·m | p. 496 | |
| Caliper Banjo fitting | 27.1 ± 1.36 N·m | 20 ft·lb | p. 496 |
| Magnetic check plug | 6 ± 1 N·m | p. 501 | |
| Drain plug | 6 ± 1.02 N·m | 53 in·lb | p. 502 |
| Bearing | 24.5 ± 3.5 N·m | p. 508 |
Füllmengen
Die vollständige Datei wird vom Bot geliefert.
| Artikel | Wert | Passt auch | PDF-Seite |
|---|---|---|---|
| Fuel tank | 36 L | p. 646 |
Zündkerzen
Die vollständige Datei wird vom Bot geliefert.
| Artikel | Wert | Passt auch | PDF-Seite |
|---|---|---|---|
| Spark plug | 0.6 mm | p. 626 |
Wartungsintervalle
Die vollständige Datei wird vom Bot geliefert.
| Artikel | Wert | Passt auch | PDF-Seite |
|---|---|---|---|
| Drive chain service | 500 km | p. 14 | |
| Coolant change | 5 years | p. 15 |
Dokument beziehen
Die vollständige Datei wird vom Bot geliefert.
In Telegram öffnen — der Bot findet dieses Dokument anhand seiner Katalog-ID und sendet die Datei.
Im Bot öffnen- Offizielle kostenlose Ski-Doo-BedienungsanleitungenTeilekatalogAlle Handbücher