BRP Defender 2019 Werkstatthandbuch — This
BRP Defender · 2019 · Werkstatthandbuch · 809 Seiten
Technische Daten
Die vollständige Datei wird vom Bot geliefert.
Anzugsdrehmoment
Die vollständige Datei wird vom Bot geliefert.
| Artikel | Wert | Passt auch | PDF-Seite |
|---|---|---|---|
| Magnetic drain plug | 29.8 ± 1.36 N·m | 22 ft·lb | p. 21 |
| Oil filter cover screws | 10 ± 1 N·m | p. 22 | |
| Coolant drain plug | 10.1 ± 1.02 N·m | 89 in·lb | p. 24 |
| Radiator hose clamp | 3.1 ± 0.45 N·m | 27 in·lb | p. 24 |
| Drain plug | 7.5 ± 0.45 N·m | 66 in·lb | p. 28 |
| Filler plug | 7.5 ± 0.45 N·m | 66 in·lb | p. 28 |
| Filler plug | 16.5 ± 2.5 N·m | p. 29 | |
| Spark plug | 20.3 ± 1.36 N·m | 15 ft·lb | p. 29 |
| Drain plug | 2.7 ± 0.34 N·m | 24 in·lb | p. 30 |
| Drain plug | 100 ± 10 N·m | p. 30 | |
| Otherwise, engine performance degradation | 10 ± 2 N·m | p. 45 | |
| PROCEDURES Air filter housing screws | 10.1 ± 2.03 N·m | 89 in·lb | p. 45 |
| Heat shield clamps | 4 ± 0.45 N·m | 35 in·lb | p. 50 |
| Heat shield clamps | 8 ± 0.5 N·m | p. 50 | |
| Heat shield clamps | 0.5 N·m | p. 50 | |
| Oil pump cover screws | 10.1 ± 1.02 N·m | 89 in·lb | p. 61 |
| Thermostat cover | 6 ± 0.7 N·m | p. 65 | |
| Water pump housing | 10 ± 1 N·m | p. 66 | |
| M6 magneto cover | 10 ± 1 N·m | p. 81 | |
| Bearing cover screws | 24.4 ± 2.71 N·m | 18 ft·lb | p. 81 |
| Bearing cover screws | 25 ± 3 N·m | p. 81 | |
| Shaft for wear or damages | 35 ± 4 N·m | p. 84 | |
| Rotor retaining nut | 180 ± 10 N·m | p. 84 | |
| Moval of starter drive cover | 10 ± 1 N·m | p. 86 | |
| Starter mounting screws | 10.1 ± 1.02 N·m | 89 in·lb | p. 86 |
| Intake manifold | 20 ± 2 N·m | p. 92 | |
| Valve cover retaining | 7 ± 0.8 N·m | p. 99 | |
| Pan head screw der head | 10.1 ± 1.02 N·m | 89 in·lb | p. 101 |
| Cylinder | 20.3 ± 1.36 N·m | 15 ft·lb | p. 105 |
| Chain tensioner plug | 4.5 ± 0.45 N·m | 40 in·lb | p. 121 |
| Camshaft Camshaft timing gear | 10 ± 1 N·m | p. 123 | |
| Timing chain guide | 10 ± 1 N·m | p. 125 | |
| Bearing screw | 10.1 ± 1.02 N·m | 89 in·lb | p. 125 |
| Coupling sleeve retaining | 45 ± 5 N·m | p. 130 | |
| Counter shaft ball bearing Crankcase M8 retaining | 25 ± 3 N·m | p. 140 | |
| CVT cover retaining | 7 ± 0.8 N·m | p. 152 | |
| CVT cover screws | 7 ± 0.79 N·m | 62 in·lb | p. 152 |
| Drive pulley screw counterclockwise | 100 ± 7 N·m | p. 162 | |
| Driven pulley screw | 20 ± 1 N·m | p. 169 | |
| VSS retaining screw | 10.1 ± 1.02 N·m | 89 in·lb | p. 176 |
| Indicator switch | 3.1 ± 0.45 N·m | 27 in·lb | p. 191 |
| Protection plate retaining | 10 ± 1 N·m | p. 192 | |
| Actuator screws | 20.3 ± 1.36 N·m | 15 ft·lb | p. 194 |
| Coupling unit screws | 24.4 ± 4.07 N·m | 18 ft·lb | p. 199 |
| Shift lever knob jam nut | 15.5 ± 1.47 N·m | 137 in·lb | p. 202 |
| Shift plate nut | 9 ± 1 N·m | p. 204 | |
| Accelerator pedal | 13 ± 1 N·m | p. 259 | |
| Retaining nuts | 13 ± 1.02 N·m | 115 in·lb | p. 259 |
| ECM retaining screws | 2.5 ± 0.45 N·m | 22 in·lb | p. 265 |
| Fuel rail retaining screws | 10 ± 1 N·m | p. 269 | |
| Throttle body retaining | 10 ± 1 N·m | p. 271 | |
| CPS retaining screw | 10 ± 1 N·m | p. 273 | |
| Fuel hose adapter location retaining screws | 20.3 ± 1.36 N·m | 15 ft·lb | p. 281 |
| Fuel tank straps retaining | 23 ± 3 N·m | p. 284 | |
| Fuel pump electric connector nuts | 23 ± 2.71 N·m | 17 ft·lb | p. 284 |
| Fuel pump retaining nut | 28.5 ± 1.36 N·m | 21 ft·lb | p. 287 |
| BOX 1 (RD/GN WIRE) V-Twin engine | 9 ± 1 N·m | p. 294 | |
| Single Cylinder Engine | 17.5 ± 2.5 N·m | p. 295 | |
| Ignition switch | 10 ± 9 N·m | p. 313 | |
| Spark plug | 11 ± 1.02 N·m | 97 in·lb | p. 316 |
| Battery holder retaining | 3.4 ± 0.3 N·m | p. 323 | |
| Winch retaining screws | 16 ± 2 N·m | p. 338 | |
| Cotter pin | 249.5 ± 14.91 N·m | 184 ft·lb | p. 342 |
| Propeller shaft nut | 31.5 ± 3.5 N·m | p. 344 | |
| Propeller shaft nut | 61 ± 9 N·m | p. 344 | |
| Ring gear screws | 37 ± 3 N·m | p. 350 | |
| Differential housing | 23.5 ± 3.5 N·m | p. 351 | |
| Differential retaining | 65 ± 5 N·m | p. 351 | |
| Wheel lug nuts | 100.3 ± 9.49 N·m | 74 ft·lb | p. 364 |
| Tie rod end locking nut | 33.9 ± 1.36 N·m | 25 ft·lb | p. 369 |
| Steering wheel nut | 60 ± 5 N·m | p. 369 | |
| Steering shaft yoke nut | 40.7 ± 5.42 N·m | 30 ft·lb | p. 371 |
| Tie rod end retaining nut | 47.5 ± 5.42 N·m | 35 ft·lb | p. 373 |
| Steering column | 10 N·m | p. 378 | |
| Steering wheel centered and no effort | 1.5 N·m | p. 379 | |
| Battery connections | 8 N·m | p. 382 | |
| Battery connections | 5 N·m | p. 382 | |
| Suspension | 62.4 ± 8.13 N·m | 46 ft·lb | p. 387 |
| Stabilizer link nut | 61 ± 9 N·m | p. 389 | |
| Suspension | 61 ± 9 N·m | p. 392 | |
| Suspension | 3 ± 0.5 N·m | p. 392 | |
| Suspension | 3.1 ± 0.45 N·m | 27 in·lb | p. 392 |
| Brake light switch | 28.5 ± 1.36 N·m | 21 ft·lb | p. 402 |
| Fitting screw | 28.5 ± 1.5 N·m | p. 403 | |
| Master cylinder push rod clip | 28.5 ± 1.36 N·m | 21 ft·lb | p. 403 |
| Rod locking nut | 14 ± 1.02 N·m | 124 in·lb | p. 404 |
| Brake hose banjo | 28.5 ± 1.5 N·m | p. 405 | |
| Caliper retaining screw | 61 ± 9.49 N·m | 45 ft·lb | p. 405 |
| Brake pad pin | 10.1 ± 1.47 N·m | 89 in·lb | p. 406 |
| Pre-filter | 2.5 ± 0.5 N·m | p. 730 |
Füllmengen
Die vollständige Datei wird vom Bot geliefert.
| Artikel | Wert | Passt auch | PDF-Seite |
|---|---|---|---|
| Fuel tank | 40 L | p. 430 |
Zündkerzen
Die vollständige Datei wird vom Bot geliefert.
| Artikel | Wert | Passt auch | PDF-Seite |
|---|---|---|---|
| HD8 | — | p. 17 | |
| HD5 | — | p. 29 | |
| M10 | — | p. 103 |
Wartungsintervalle
Die vollständige Datei wird vom Bot geliefert.
| Artikel | Wert | Passt auch | PDF-Seite |
|---|---|---|---|
| Brake inspection | 2 years | p. 17 |
Dokument beziehen
Die vollständige Datei wird vom Bot geliefert.
In Telegram öffnen — der Bot findet dieses Dokument anhand seiner Katalog-ID und sendet die Datei.
Im Bot öffnen- TeilekatalogAlle Handbücher