BRP Drive ETEC Gen5 2024 Manual
BRP Drive ETEC Gen5 · 2024 · manual · 90 pages
Technical data
Numbers below were extracted automatically from the document. Verify them against the original manual before you order parts or apply torque.
Tightening torque
Values extracted from the document text. Check against the original before service work.
| Item | Value | Also | PDF page |
|---|---|---|---|
| Drive Belt Guard Support | 7.5 ± 1 N·m | p. 12 | |
| M6 Torx screw | 7.5 ± 1.02 N·m | 66 in·lb | p. 12 |
| Flange screw | 2 ± 0.23 N·m | 18 in·lb | p. 12 |
| Drive Belt Width | 1.8 ± 0.2 N·m | p. 14 | |
| Retaining screws | 20.3 ± 1.36 N·m | 15 ft·lb | p. 22 |
| Roller axle screw (P/N 529036376) | 5 ± 0.45 N·m | 44 in·lb | p. 31 |
| Damper screws | 31.2 ± 4.07 N·m | 23 ft·lb | p. 32 |
| NOTICE bolt | 120.7 ± 5.42 N·m | 89 ft·lb | p. 33 |
| Pivot screws | 16.9 ± 1.02 N·m | 150 in·lb | p. 40 |
| Cam screw | 31.2 ± 4.07 N·m | 23 ft·lb | p. 41 |
| Upper gear screw | 48 ± 6 N·m | p. 42 | |
| Upper gear screw | 15.5 ± 1.5 N·m | p. 42 | |
| Bearing flange nut | 15.5 ± 1.5 N·m | 137 in·lb | p. 42 |
| Without Adjustable Lever | 27 ± 1 N·m | p. 46 | |
| Adjustable Lever | 1.15 ± 0.35 N·m | p. 47 | |
| Reservoir cap screws | 0.7 ± 0.11 N·m | 6 in·lb | p. 49 |
| Brake caliper bleeder | 8 ± 1.02 N·m | 71 in·lb | p. 50 |
| Squeeze brake lever | 6 ± 1 N·m | p. 53 | |
| Pistons by small steps | 6 ± 1 N·m | p. 54 | |
| Brake lever pivot nut | 6 ± 1.02 N·m | 53 in·lb | p. 54 |
| Brake pad pin | 10.1 ± 2.03 N·m | 89 in·lb | p. 56 |
| Guard nut | 9 ± 1 N·m | p. 57 | |
| Guard screw | 0.7 ± 0.08 N·m | 6.6 in·lb | p. 57 |
| Toe hold nuts | 1 ± 0.11 N·m | 9 in·lb | p. 57 |
| Caliper screws | 24.4 ± 4.07 N·m | 18 ft·lb | p. 61 |
| Banjo bolt | 2.9 ± 1.02 N·m | 25.8 in·lb | p. 62 |
| Master Cylinder | 0.7 ± 0.08 N·m | 6.6 in·lb | p. 63 |
| Reservoir screw | 1.1 ± 0.34 N·m | 10 in·lb | p. 65 |
| Master cylinder clamp | 9 ± 1 N·m | p. 66 | |
| Clamp screws | 8.5 ± 1.47 N·m | 75 in·lb | p. 66 |
| Brake light micro | 5.5 ± 1.5 N·m | p. 67 | |
| Switch screw | 5.5 ± 1.47 N·m | 49 in·lb | p. 67 |
| Clamp screw | 10.1 ± 2.03 N·m | 89 in·lb | p. 69 |
| Clamp screw | 35 ± 1 N·m | p. 69 | |
| Caliper Banjo fitting | 35.3 ± 1.36 N·m | 26 ft·lb | p. 69 |
| Master cylinder Banjo | 27 ± 1 N·m | p. 69 | |
| Caliper Banjo fitting | 27.1 ± 1.36 N·m | 20 ft·lb | p. 69 |
| Clamp screw | 8.5 ± 1.47 N·m | 75 in·lb | p. 69 |
| Drain plug | 6 ± 1 N·m | 53 in·lb | p. 72 |
| M6 Screws | 7 ± 1 N·m | p. 79 | |
| Flanged nuts | 7 ± 1.02 N·m | 62 in·lb | p. 79 |
| M8 Screws | 14.5 ± 1.5 N·m | p. 79 | |
| Flanged nuts | 10 ± 2 N·m | 7.3 ft·lb | p. 79 |
Get the document
The full file is delivered by the bot. Free owner guides for BRP are also available from the manufacturer.
Open in Telegram — the bot finds this document by its catalog id and sends the file.
Open in bot- Official free BRP owner's manualsParts catalogueAll manuals