KTM 20450SX 20505SX 2010 Manual
KTM 20450SX 20505SX · 2010 · manual · 247 pages
Technical data
Numbers below were extracted automatically from the document. Verify them against the original manual before you order parts or apply torque.
Tightening torque
Values extracted from the document text. Check against the original before service work.
| Item | Value | Also | PDF page |
|---|---|---|---|
| Screw, steering bridge | 20 N·m | p. 15 | |
| Screw, steering column, top | 25 N·m | p. 15 | |
| Nut, handlebar support | 45 N·m | p. 15 | |
| Screw, handlebar clamp | 20 N·m | p. 15 | |
| Screw, bearing support, steering | 25 N·m | p. 20 | |
| Screw, steering column at bottom | 25 N·m | p. 20 | |
| Steering lever | 24.9 N·m | 18.4 ft·lb | p. 20 |
| Screw, steering column, bottom | 40 N·m | p. 21 | |
| Screw, front shock absorber | 45 N·m | p. 27 | |
| Nut, piston rod | 30 N·m | p. 35 | |
| Screw, rear top shock absorber | 60 N·m | p. 44 | |
| Screw, rear bottom shock absorber | 70 N·m | p. 44 | |
| Screw on fuel tank | 6 N·m | 4.4 ft·lb | p. 66 |
| Wheel nut | 45 N·m | p. 75 | |
| Wheel nuts crosswise | 45 N·m | 33.2 ft·lb | p. 75 |
| Screw, rear wheel eccentric element | 20 N·m | p. 79 | |
| Nut, rear wheel hub | 130 N·m | p. 80 | |
| Screw, clamping nut, rear axle | 10 N·m | 7.4 ft·lb | p. 82 |
| Screw, rear brake caliper | 10 N·m | p. 82 | |
| Danger of accidents Brake system failure | 15 N·m | 11.1 ft·lb | p. 96 |
| Engine mounting bolt | 60 N·m | p. 103 | |
| Engine bracket screw | 60 N·m | p. 103 | |
| Nut, swingarm pivot | 100 N·m | p. 103 | |
| Screw, starter motor | 10 N·m | 7.4 ft·lb | p. 104 |
| Screw, clutch slave cylinder | 10 N·m | 7.4 ft·lb | p. 104 |
| Pump idler shaft | 6 N·m | 4.4 ft·lb | p. 120 |
| Locking screw for bearing | 6 N·m | p. 121 | |
| Oil suction pipe | 15 N·m | p. 122 | |
| Nut, compensating | 20 N·m | p. 124 | |
| Nut, water-pump wheel | 6 N·m | p. 124 | |
| Oil pressure regulator valve plug | 18 N·m | p. 126 | |
| Screw, engine case | 14 N·m | p. 129 | |
| Screw, camshaft gear | 50 N·m | p. 132 | |
| Screw, camshaft bearing | 14 N·m | p. 133 | |
| Screw plug, cam lever shafts | 10 N·m | 7.4 ft·lb | p. 136 |
| 301663-10 Screw, engine case | 10 N·m | 7.4 ft·lb | p. 148 |
| Screw, locking lever | 6 N·m | p. 149 | |
| 301661-11 Screw, shift drum locating | 10 N·m | p. 149 | |
| Screw, oil pump cover | 6 N·m | p. 149 | |
| Screw, oil pump casing | 10 N·m | p. 151 | |
| Nut, primary gear | 80 N·m | p. 151 | |
| Nut, inner clutch hub | 80 N·m | p. 152 | |
| Screw, clutch spring | 10 N·m | 7.4 ft·lb | p. 152 |
| Nut, freewheel hub | 80 N·m | p. 153 | |
| Retaining bracket | 6 N·m | 4.4 ft·lb | p. 153 |
| Screw, ignition pulse gen | 6 N·m | p. 154 | |
| Screw, ignition pulse gen | 10 N·m | p. 154 | |
| Screw, rotor | 80 N·m | p. 154 | |
| Axle guide rail for timing chain | 15 N·m | p. 154 | |
| Axle tension rail for timing chain | 15 N·m | p. 154 | |
| 301624-11 Screw, clutch cover | 14 N·m | p. 156 | |
| Screw plug, clutch cover | 10 N·m | 7.4 ft·lb | p. 156 |
| Screw, water pump cover | 14 N·m | p. 156 | |
| Screw, water pump cover | 10 N·m | 7.4 ft·lb | p. 156 |
| Nut, cylinder head | 10 N·m | p. 157 | |
| Plug, timing chain tensioner | 25 N·m | p. 158 | |
| Screw, unlocking of timing chainsioner | 10 N·m | 7.4 ft·lb | p. 158 |
| Plug, crankshaft location | 20 N·m | p. 160 | |
| Screw, alternator cover | 10 N·m | 7.4 ft·lb | p. 161 |
| Screw, valve cover | 8 N·m | 5.9 ft·lb | p. 161 |
| Plug, oil screen | 30 N·m | p. 162 | |
| Screw, oil filter cover | 6 N·m | 4.4 ft·lb | p. 162 |
| Screw, shift lever | 10 N·m | p. 163 | |
| Other screws, carburetor | 5 N·m | 3.7 ft·lb | p. 168 |
| Choke slide | 2.5 N·m | p. 177 | |
| Screw, hose connection | 2 N·m | p. 177 | |
| Mixture control screw | 1 N·m | 0.7 ft·lb | p. 177 |
| Needle screw | 3.5 N·m | p. 178 | |
| Screw, throttle slide arm | 2 N·m | p. 178 | |
| Other screws, carburetor | 2 N·m | 1.5 ft·lb | p. 178 |
| Screw, engine sprocket | 60 N·m | p. 181 | |
| Screw, stator bracket | 6 N·m | p. 189 | |
| Screw, stator cable holder | 6 N·m | p. 189 | |
| Lock nut, tie rod, outside | 20 N·m | 14.8 ft·lb | p. 194 |
| Lock nut, tie rod, inside | 20 N·m | 14.8 ft·lb | p. 194 |
| Screw, A-arm top | 45 N·m | p. 195 | |
| Nut, A-arm top | 30 N·m | p. 195 | |
| Nut, front wheel hub | 70 N·m | p. 199 | |
| Nut, ball head, A-arm bottom | 40 N·m | p. 199 | |
| Nut, ball head, A-arm top | 35 N·m | p. 199 | |
| Nut, tie rod end | 45 N·m | p. 200 | |
| Screw, front brake caliper | 20 N·m | p. 200 | |
| Screw, A-arm bottom | 45 N·m | p. 201 | |
| Screw, bearing bolt of oil pump idler | 6 N·m | 4.4 ft·lb | p. 208 |
| Screw, camshaft bearing retaining | 6 N·m | 4.4 ft·lb | p. 208 |
| Screw, ignition pulse generator adapter | 6 N·m | 4.4 ft·lb | p. 208 |
| Screw, timing train axle retaining | 6 N·m | 4.4 ft·lb | p. 208 |
| Screw, exhaust flange | 10 N·m | 7.4 ft·lb | p. 208 |
| Stud, cylinder head | 10 N·m | 7.4 ft·lb | p. 208 |
| Stud, cylinder head | 20 N·m | 14.8 ft·lb | p. 209 |
Capacities
Values extracted from the document text. Check against the original before service work.
| Item | Value | Also | PDF page |
|---|---|---|---|
| Fuel tank | 10.3 L | p. 213 |
Spark plugs
Values extracted from the document text. Check against the original before service work.
| Item | Value | Also | PDF page |
|---|---|---|---|
| M10 | — | p. 162 | |
| S1N | — | p. 219 |
Get the document
The full file is delivered by the bot. Free owner guides for KTM are also available from the manufacturer.
Open in Telegram — the bot finds this document by its catalog id and sends the file.
Open in bot- Parts catalogueAll manuals