BRP Maverick 2023 Manual de serviço — This
BRP Maverick · 2023 · Manual de serviço · 1492 páginas
Dados técnicos
O ficheiro completo é enviado pelo bot.
Binário de aperto
O ficheiro completo é enviado pelo bot.
| Item | Valor | Também | Página PDF |
|---|---|---|---|
| Engine mount screw | 61 ± 9 N·m | p. 59 | |
| Engine support screws | 61 ± 9.49 N·m | 45 ft·lb | p. 59 |
| Air Intake System | 3.5 ± 0.5 N·m | p. 61 | |
| Air Intake System | 3.75 ± 0.75 N·m | p. 62 | |
| Air Intake System | 5.5 ± 0.5 N·m | p. 62 | |
| Air Intake System | 2.5 ± 0.5 N·m | p. 63 | |
| Air filter housing | 10 ± 2 N·m | p. 66 | |
| Exhaust System | 7 ± 1 N·m | p. 68 | |
| Exhaust System | 42.5 ± 2.5 N·m | p. 71 | |
| Sensor probe as it could affect its operation | 10 ± 2 N·m | p. 74 | |
| Muffler cover screws | 10.1 ± 2.03 N·m | 89 in·lb | p. 74 |
| Oxygen sensor | 50.2 ± 9.49 N·m | 37 ft·lb | p. 74 |
| Shift lever handle Nut | 15.5 ± 1.47 N·m | 137 in·lb | p. 88 |
| Shift plate nut | 9 ± 1.02 N·m | 80 in·lb | p. 90 |
| Fan screw | 8 ± 1.02 N·m | 71 in·lb | p. 95 |
| Accelerator pedal | 13 ± 1 N·m | p. 111 | |
| Retaining nuts | 13 ± 1.02 N·m | 115 in·lb | p. 111 |
| NOTICE Fuel pump nut | 59.7 ± 5.42 N·m | 44 ft·lb | p. 123 |
| Pre-filter | 2.5 ± 0.5 N·m | p. 130 | |
| Retaining screw | 2.5 ± 0.45 N·m | 22 in·lb | p. 130 |
| Protective plate | 6.5 ± 0.5 N·m | p. 130 | |
| Retaining screw | 6.6 ± 0.45 N·m | 58 in·lb | p. 130 |
| Chassis ground screw | 4.5 ± 0.45 N·m | 40 in·lb | p. 135 |
| Engine ground screw | 9 ± 1.02 N·m | 80 in·lb | p. 135 |
| Battery holder | 5 ± 1 N·m | p. 158 | |
| Retaining nut | 5 ± 1.02 N·m | 44 in·lb | p. 158 |
| Battery post screw | 4.5 ± 0.45 N·m | 40 in·lb | p. 158 |
| Overtighten spark plugs, engine dam | 11 N·m | p. 162 | |
| Spark plug | 11 N·m | 97 in·lb | p. 162 |
| Ignition coil retaining | 9 ± 1 N·m | p. 163 | |
| Retaining screws | 8 ± 1.02 N·m | 71 in·lb | p. 163 |
| Multifunction switch 4.5 | 5.5 N·m | p. 176 | |
| Wheel lug nuts | 120.7 ± 5.42 N·m | 89 ft·lb | p. 187 |
| Beadlock inner ring shoulder | 24.4 ± 1.36 N·m | 18 ft·lb | p. 188 |
| Beadlock screws | 14 ± 1 N·m | p. 188 | |
| Beadlock clamp ring edge | 14 ± 1.02 N·m | 124 in·lb | p. 188 |
| Beadlock screws | 25 ± 1 N·m | p. 189 | |
| Smart-Lok Differential | 12 ± 2 N·m | p. 191 | |
| Castellated nut | 249.5 ± 14.91 N·m | 184 ft·lb | p. 210 |
| Peller shaft nut | 48 ± 6 N·m | p. 214 | |
| Bearing flange bolts | 47.5 ± 5.42 N·m | 35 ft·lb | p. 214 |
| Bearing flange bolts | 31.5 ± 3.5 N·m | p. 214 | |
| Propeller shaft nut | 31.2 ± 4.07 N·m | 23 ft·lb | p. 214 |
| Sleeve locking nuts | 33.9 ± 1.36 N·m | 25 ft·lb | p. 226 |
| UNEQUAL TURNING RADIUS B on nut | 40.7 ± 5.42 N·m | 30 ft·lb | p. 226 |
| C on bolts | 21.7 ± 1.36 N·m | 16 ft·lb | p. 226 |
| Steering wheel nut | 59.7 ± 5.42 N·m | 44 ft·lb | p. 227 |
| Nut only | 40 ± 5 N·m | p. 230 | |
| Steering shaft yoke nut | 40.7 ± 5.42 N·m | 30 ft·lb | p. 230 |
| Steering shaft pinch | 40 ± 5 N·m | p. 231 | |
| Tie-rod end nut | 104.4 ± 14.91 N·m | 77 ft·lb | p. 237 |
| Tie-rod end jam nut | 33.9 ± 1.36 N·m | 25 ft·lb | p. 237 |
| Steering column | 10 N·m | p. 243 | |
| IMU retaining screws | 10.1 ± 2.03 N·m | 89 in·lb | p. 269 |
| SPS screw | 5 ± 0.45 N·m | 44 in·lb | p. 269 |
| VAS screw and nut | 10.1 ± 2.03 N·m | 89 in·lb | p. 270 |
| SDCU screw | 1.1 ± 0.11 N·m | 10 in·lb | p. 271 |
| Front Suspension | 120 ± 10 N·m | p. 273 | |
| Suspension | 0.75 ± 0.25 N·m | p. 273 | |
| Suspension | 0.8 ± 0.23 N·m | 7 in·lb | p. 273 |
| Shock absorber nuts | 120.7 ± 9.49 N·m | 89 ft·lb | p. 276 |
| Suspension | 120.7 ± 9.49 N·m | 89 ft·lb | p. 281 |
| Rear Suspension | 120 ± 10 N·m | p. 282 | |
| Brakes | 1.2 ± 0.1 N·m | p. 289 | |
| Brake light switch | 28.5 ± 1.5 N·m | p. 291 | |
| Cylinder | 28.5 ± 1.36 N·m | 21 ft·lb | p. 291 |
| Ment, remove brake hose banjo fitting screw | 28.5 ± 1.5 N·m | p. 292 | |
| Caliper retaining screw | 50.2 ± 4.07 N·m | 37 ft·lb | p. 293 |
| Brake pad pin | 10.1 ± 1.47 N·m | 89 in·lb | p. 293 |
| Brake disc screw | 33.9 ± 4.07 N·m | 25 ft·lb | p. 294 |
| Wheel lug nut | 120.7 ± 5.42 N·m | 89 ft·lb | p. 351 |
| Intake manifold screws | 9 ± 1.02 N·m | 80 in·lb | p. 407 |
| Clamps | 4 ± 0.45 N·m | 35 in·lb | p. 407 |
| Secondary drain plug | 15 ± 2.03 N·m | 133 in·lb | p. 415 |
| Secondary drain plug | 30 ± 3 N·m | p. 415 | |
| Magnetic drain plug | 29.8 ± 2.71 N·m | 22 ft·lb | p. 415 |
| Oil filler tube screw | 7 ± 0.79 N·m | 62 in·lb | p. 418 |
| Cylinder block | 10.1 ± 1.02 N·m | 89 in·lb | p. 419 |
| Cover screws | 11 ± 1 N·m | p. 428 | |
| Washers | 15 ± 2 N·m | p. 428 | |
| Secondary drain plug | 5 ± 0.6 N·m | p. 428 | |
| Cover screws | 5 ± 0.56 N·m | 44 in·lb | p. 428 |
| Banjo bolt | 19 ± 2.03 N·m | 168 in·lb | p. 430 |
| Water pump housing | 9 ± 1 N·m | p. 438 | |
| Water pump drive gear | 9 ± 1 N·m | p. 439 | |
| Magneto and Starter | 9 ± 1 N·m | p. 441 | |
| CPS screw | 9 ± 1 N·m | p. 443 | |
| Stator Continuity Test | 9 ± 1 N·m | p. 445 | |
| Magneto cover screws | 9 ± 1.02 N·m | 80 in·lb | p. 445 |
| Rotor retaining screw | 150.5 ± 9.49 N·m | 111 ft·lb | p. 448 |
| Sprag clutch housing | 30 ± 2 N·m | p. 449 | |
| Starter screws | 9 ± 1 N·m | p. 451 |
Velas de ignição
O ficheiro completo é enviado pelo bot.
| Item | Valor | Também | Página PDF |
|---|---|---|---|
| HD9 | — | p. 1002 | |
| HD8 | — | p. 1002 | |
| G2L | — | p. 1003 | |
| HD10 | — | p. 1005 | |
| MA2 | — | p. 1195 |
Intervalos de manutenção
O ficheiro completo é enviado pelo bot.
| Item | Valor | Também | Página PDF |
|---|---|---|---|
| Spark plug service | 5 years | p. 44 | |
| Coolant change | 5 years | p. 80 | |
| Brake inspection | 2 years | p. 1144 |
Obter o documento
O ficheiro completo é enviado pelo bot.
Abrir no Telegram — o bot localiza este documento pelo seu id de catálogo e envia o ficheiro.
Abrir no bot- Catálogo de peçasTodos os manuais