Ski-Doo MY21 Freeride Pdf 2021 Manual
Ski-Doo MY21 Freeride Pdf · 2021 · Manual · 427 páginas
Dados técnicos
O ficheiro completo é enviado pelo bot.
Binário de aperto
O ficheiro completo é enviado pelo bot.
| Item | Valor | Também | Página PDF |
|---|---|---|---|
| INTAKE SYSTEM subsection | 31.2 ± 4.07 N·m | 23 ft·lb | p. 42 |
| Snug all bolts | 33 ± 3 N·m | p. 42 | |
| Panel nut | 1.8 ± 0.23 N·m | 16 in·lb | p. 56 |
| Muffler retaining screw | 7 ± 1.02 N·m | 62 in·lb | p. 61 |
| Exhaust Gas | 45 ± 2 N·m | p. 66 | |
| Temperature Sensor | 44.7 ± 1.36 N·m | 33 ft·lb | p. 66 |
| Exhaust pipe | 28 ± 1 N·m | p. 71 | |
| Oetiker clamp | 1.7 ± 0.2 N·m | p. 74 | |
| EPS retaining screw | 1.7 ± 0.23 N·m | 15 in·lb | p. 74 |
| Cylinder | 5.5 ± 0.5 N·m | p. 77 | |
| Head | 5.5 ± 0.45 N·m | 49 in·lb | p. 77 |
| Coolant hose clamp | 3.1 ± 0.45 N·m | 27 in·lb | p. 79 |
| M6 screw on chassis | 10 ± 2 N·m | p. 126 | |
| Battery terminals | 10 ± 2 N·m | p. 166 | |
| Battery hold down | 5 ± 0.5 N·m | p. 166 | |
| Bracket | 5 ± 0.45 N·m | 44 in·lb | p. 166 |
| Battery cover retaining | 7 ± 1 N·m | p. 166 | |
| Solenoid cable retaining | 4 ± 0.5 N·m | p. 177 | |
| Retaining screws | 1 ± 0.23 N·m | 9 in·lb | p. 192 |
| Torx screw | 7.5 ± 1.02 N·m | 66 in·lb | p. 205 |
| Elastic nut | 10.1 ± 2.03 N·m | 89 in·lb | p. 205 |
| Clamping screw | 5.5 ± 0.45 N·m | 49 in·lb | p. 207 |
| Roller axle screw | 5 ± 0.5 N·m | p. 218 | |
| Drive pulley bolt | 120 N·m | p. 220 | |
| Drive pulley bolt First | 120.7 N·m | 89 ft·lb | p. 220 |
| Damper screws | 31.2 ± 4.07 N·m | 23 ft·lb | p. 220 |
| Bearing flange nut | 15.5 ± 1.47 N·m | 137 in·lb | p. 229 |
| Brake lever pivot nut | 6 ± 1 N·m | p. 235 | |
| Brake lever pivot nut | 8.5 ± 1.5 N·m | p. 235 | |
| Brake caliper bleeder | 8.5 ± 1.47 N·m | 75 in·lb | p. 235 |
| Brake pad pin | 10.1 ± 2.03 N·m | 89 in·lb | p. 237 |
| Master cylinder clamp | 9 ± 1 N·m | p. 240 | |
| Washers | 27 ± 1 N·m | p. 240 | |
| Middle clamp nut | 2.3 ± 0.23 N·m | 20 in·lb | p. 242 |
| Middle clamp nut | 35 ± 1 N·m | p. 242 | |
| Caliper Banjo fitting | 35.3 ± 1.36 N·m | 26 ft·lb | p. 242 |
| Master cylinder Banjo | 27 ± 1 N·m | p. 242 | |
| Caliper Banjo fitting | 27.1 ± 1.36 N·m | 20 ft·lb | p. 242 |
| Magnetic check plug | 6 ± 1 N·m | p. 245 | |
| Drain plug | 6 ± 1.02 N·m | 53 in·lb | p. 246 |
| Bearing | 24.5 ± 3.5 N·m | p. 252 | |
| Rear idler wheel | 48 ± 6 N·m | p. 261 | |
| Retaining screws | 47.5 ± 5.42 N·m | 35 ft·lb | p. 261 |
| Rear idler wheel | 24.5 ± 3.5 N·m | p. 261 | |
| Front shock absorber | 31.5 ± 3.5 N·m | p. 272 | |
| Retaining nuts | 31.2 ± 4.07 N·m | 23 ft·lb | p. 272 |
| Front arm bolts | 47.5 ± 5.42 N·m | 35 ft·lb | p. 287 |
| Rear arm connecting | 61 N·m | p. 287 | |
| Rod screws | 61 ± 9.49 N·m | 45 ft·lb | p. 287 |
| Clamp screws | 2.5 ± 0.45 N·m | 22 in·lb | p. 288 |
| Clamp screws | 0.4 ± 0.1 N·m | p. 288 | |
| Knob screw | 0.5 ± 0.11 N·m | 4 in·lb | p. 288 |
| Support screws | 5 ± 1.02 N·m | 44 in·lb | p. 290 |
| Support screws | 2.5 ± 0.5 N·m | p. 290 | |
| Clamp screws | 1.5 ± 0.5 N·m | p. 290 | |
| Bleeding and Reassembling Spring | 24.4 ± 4.07 N·m | 18 ft·lb | p. 293 |
| Banjo bolt | 24.4 ± 4.07 N·m | 18 ft·lb | p. 294 |
| Jam nut | 18.5 ± 3.5 N·m | 164 in·lb | p. 334 |
| Runner nut | 8 ± 1.02 N·m | 71 in·lb | p. 335 |
| Ski nut | 47.5 ± 5.42 N·m | 35 ft·lb | p. 336 |
| Adjusting knob screw | 9 ± 1.02 N·m | 80 in·lb | p. 339 |
| Adjusting knob screw | 24.5 ± 3.5 N·m | p. 339 | |
| Indicator screw | 24.4 ± 4.07 N·m | 18 ft·lb | p. 339 |
| Extension nuts | 3 ± 0.5 N·m | p. 341 | |
| Extension nuts | 3.1 ± 0.45 N·m | 27 in·lb | p. 341 |
| Multifunction switch | 2.4 ± 0.2 N·m | p. 343 | |
| Throttle lever retaining | 1.5 ± 0.2 N·m | p. 345 | |
| Throttle lever pivot | 1.5 ± 0.2 N·m | p. 346 | |
| Clamp screws | 24.4 ± 4.07 N·m | 18 ft·lb | p. 347 |
| Outer tie-rod end nut | 48 ± 6 N·m | p. 350 | |
| Outer tie-rod end nut | 24.5 ± 3.5 N·m | p. 350 | |
| Inner tie-rod end nut | 24.4 ± 4.07 N·m | 18 ft·lb | p. 350 |
| Upper steering column | 12.5 ± 2.5 N·m | p. 352 | |
| Support nut | 12.5 ± 2.49 N·m | 111 in·lb | p. 352 |
| Lower steering column | 23.5 ± 3.5 N·m | p. 352 | |
| Support nut | 23 ± 4.07 N·m | 17 ft·lb | p. 352 |
| Housing screw | 2.3 ± 0.23 N·m | 20 in·lb | p. 358 |
| Gauge support screw | 2.3 ± 0.23 N·m | 20 in·lb | p. 360 |
| Hood hexagonal screw | 1.8 ± 0.23 N·m | 16 in·lb | p. 362 |
| Hood hexagonal screw | 2.3 ± 0.2 N·m | p. 362 | |
| Hood Torx screw | 2.3 ± 0.02 N·m | 20 in·lb | p. 362 |
| Headlight Torx screw | 2.3 ± 0.23 N·m | 20 in·lb | p. 362 |
| Console nut | 2.3 ± 0.23 N·m | 20 in·lb | p. 363 |
| Front bumper nut | 5 ± 0.45 N·m | 44 in·lb | p. 364 |
| Side bottom pan screw | 2.8 ± 0.23 N·m | 25 in·lb | p. 366 |
| Rear bumper screws | 16 ± 2.03 N·m | 142 in·lb | p. 367 |
| Pinched nut | 2.8 ± 0.23 N·m | 25 in·lb | p. 381 |
| Side bottom pan screw | 1.8 ± 0.2 N·m | p. 381 | |
| Rear hitch nuts | 31.2 ± 4.07 N·m | 23 ft·lb | p. 384 |
| Multi-LinQ plate screws | 7 ± 1.02 N·m | 62 in·lb | p. 385 |
Capacidades
O ficheiro completo é enviado pelo bot.
| Item | Valor | Também | Página PDF |
|---|---|---|---|
| Fuel tank | 36 L | p. 421 |
Intervalos de manutenção
O ficheiro completo é enviado pelo bot.
| Item | Valor | Também | Página PDF |
|---|---|---|---|
| Drive chain service | 500 km | p. 27 | |
| Coolant change | 5 years | p. 28 |
Obter o documento
O ficheiro completo é enviado pelo bot.
Abrir no Telegram — o bot localiza este documento pelo seu id de catálogo e envia o ficheiro.
Abrir no bot- Catálogo de peçasTodos os manuais