Ski-Doo MY22 Grand Touring 2022 Manual
Ski-Doo MY22 Grand Touring · 2022 · Manual · 633 páginas
Dados técnicos
O ficheiro completo é enviado pelo bot.
Binário de aperto
O ficheiro completo é enviado pelo bot.
| Item | Valor | Também | Página PDF |
|---|---|---|---|
| Engine rubber mount | 24.5 ± 3.5 N·m | p. 51 | |
| Engine support screws | 42 ± 4.07 N·m | 31 ft·lb | p. 52 |
| Front Engine Support Replacement | 42 ± 4 N·m | p. 53 | |
| ENGINE RUBBER MOUNTS Engine rubber mount | 10 ± 2 N·m | p. 54 | |
| Engine support screws | 31.2 ± 4.07 N·m | 23 ft·lb | p. 60 |
| INTAKE SYSTEM subsection | 31.2 ± 4.07 N·m | 23 ft·lb | p. 72 |
| Snug all bolts | 33 ± 3 N·m | p. 72 | |
| Muffler retaining screw | 7 ± 1.02 N·m | 62 in·lb | p. 89 |
| Exhaust pipe retaining | 7 ± 1 N·m | p. 89 | |
| Exhaust Gas | 45 ± 2 N·m | p. 110 | |
| Temperature Sensor | 44.7 ± 1.36 N·m | 33 ft·lb | p. 110 |
| From throttle | 1.2 ± 0.2 N·m | p. 113 | |
| Magneto cover | 9 ± 1 N·m | p. 121 | |
| Turbo engine | 2.5 ± 0.5 N·m | p. 129 | |
| Drain screws | 9 ± 1 N·m | p. 131 | |
| Cylinder | 5.5 ± 0.5 N·m | p. 137 | |
| Head | 5.5 ± 0.45 N·m | 49 in·lb | p. 137 |
| Coolant hose clamp | 3.1 ± 0.45 N·m | 27 in·lb | p. 139 |
| M6 screw on chassis | 10 ± 2 N·m | p. 216 | |
| Battery terminals | 10 ± 2 N·m | p. 255 | |
| Battery hold down | 7 ± 1 N·m | p. 255 | |
| Bracket | 7 ± 1.02 N·m | 62 in·lb | p. 255 |
| Battery cover retaining | 7 ± 1 N·m | p. 255 | |
| Battery hold down | 5 ± 0.5 N·m | p. 260 | |
| Bracket | 5 ± 0.45 N·m | 44 in·lb | p. 260 |
| Solenoid cable retaining | 4 ± 0.5 N·m | p. 271 | |
| Retaining screws | 1 ± 0.23 N·m | 9 in·lb | p. 294 |
| Distorted spare belt | 10 ± 2 N·m | p. 319 | |
| Distorted spare belt | 24.5 ± 3.5 N·m | p. 319 | |
| Clamping screw | 5.5 ± 0.45 N·m | 49 in·lb | p. 321 |
| Torx screw | 7.5 ± 1.02 N·m | 66 in·lb | p. 325 |
| Elastic nut | 10.1 ± 2.03 N·m | 89 in·lb | p. 325 |
| Centrifugal lever | 5 ± 0.6 N·m | p. 336 | |
| Pivot nut | 5 ± 0.56 N·m | 44 in·lb | p. 336 |
| Spring cover retaining | 10 ± 2 N·m | p. 336 | |
| Roller axle screw | 5 ± 0.45 N·m | 44 in·lb | p. 348 |
| Damper screws | 31.2 ± 4.07 N·m | 23 ft·lb | p. 349 |
| Drive pulley bolt | 120 N·m | p. 362 | |
| Drive pulley bolt First | 120.7 N·m | 89 ft·lb | p. 362 |
| Pivot screws | 17 ± 1 N·m | 150 in·lb | p. 372 |
| Bearing flange nut | 15.5 ± 1.47 N·m | 137 in·lb | p. 373 |
| Brake lever pivot nut | 6 ± 1 N·m | p. 391 | |
| Brake lever pivot nut | 8.5 ± 1.5 N·m | p. 391 | |
| Brake caliper bleeder | 8.5 ± 1.47 N·m | 75 in·lb | p. 391 |
| Brake pad pin | 10.1 ± 2.03 N·m | 89 in·lb | p. 393 |
| Master cylinder clamp | 9 ± 1 N·m | p. 396 | |
| Washers | 27 ± 1 N·m | p. 396 | |
| Middle clamp nut | 2.3 ± 0.23 N·m | 20 in·lb | p. 398 |
| Middle clamp nut | 35 ± 1 N·m | p. 398 | |
| Caliper Banjo fitting | 35.3 ± 1.36 N·m | 26 ft·lb | p. 398 |
| Master cylinder Banjo | 27 ± 1 N·m | p. 398 | |
| Caliper Banjo fitting | 27.1 ± 1.36 N·m | 20 ft·lb | p. 398 |
| Drain plug | 6 ± 1.02 N·m | 53 in·lb | p. 405 |
| Magnetic check plug | 6 ± 1.02 N·m | 53 in·lb | p. 405 |
| Actuator coupling | 7 ± 0.5 N·m | p. 408 | |
| 219100985-021-010 shaft nut | 7 ± 0.45 N·m | 62 in·lb | p. 408 |
| Upper gear screw | 48 ± 6 N·m | p. 420 | |
| Screws Same | 10 ± 2 N·m | p. 421 | |
| Reverse gear screw | 24.4 ± 4.07 N·m | 18 ft·lb | p. 421 |
| Bearing | 24.5 ± 3.5 N·m | p. 434 | |
| Rear idler wheel | 48 ± 6 N·m | p. 443 | |
| Retaining screws | 47.5 ± 5.42 N·m | 35 ft·lb | p. 443 |
| Rear idler wheel | 24.5 ± 3.5 N·m | p. 443 | |
| Front shock absorber | 31.5 ± 3.5 N·m | p. 454 | |
| Retaining nuts | 31.2 ± 4.07 N·m | 23 ft·lb | p. 454 |
| Front arm bolts | 47.5 ± 5.42 N·m | 35 ft·lb | p. 469 |
| Rear arm connecting | 61 N·m | p. 469 | |
| Rod screws | 61 ± 9.49 N·m | 45 ft·lb | p. 469 |
| Clamp screws | 2.5 ± 0.45 N·m | 22 in·lb | p. 470 |
| Clamp screws | 0.4 ± 0.1 N·m | p. 470 | |
| Knob screw | 0.5 ± 0.11 N·m | 4 in·lb | p. 470 |
| Support screws | 5 ± 1.02 N·m | 44 in·lb | p. 472 |
| Support screws | 2.5 ± 0.5 N·m | p. 472 | |
| Clamp screws | 1.5 ± 0.5 N·m | p. 472 | |
| Bleeding and Reassembling Spring | 24.4 ± 4.07 N·m | 18 ft·lb | p. 475 |
| Banjo bolt | 24.4 ± 4.07 N·m | 18 ft·lb | p. 476 |
| Suspension | 24.5 ± 3.5 N·m | p. 492 | |
| Front and rear arm | 48 ± 6 N·m | p. 496 | |
| Upper bolts | 47.5 ± 5.42 N·m | 35 ft·lb | p. 496 |
| Rear shock absorber | 24.5 ± 3.5 N·m | p. 497 | |
| Nuts and bolts | 24.4 ± 4.07 N·m | 18 ft·lb | p. 497 |
| Center shock absorber | 48 ± 6 N·m | p. 498 | |
| Center shock absorber | 70 ± 10 N·m | p. 498 | |
| Rear arm top axle screws | 48 ± 6 N·m | p. 499 | |
| Pipe sealant | 13 ± 1 N·m | p. 506 | |
| Pipe sealant | 9 ± 1 N·m | p. 507 | |
| Pressure sensor | 27.1 ± 2.71 N·m | 20 ft·lb | p. 516 |
| Jam nut | 18.5 ± 3.5 N·m | 164 in·lb | p. 527 |
| Runner nut | 8 ± 1.02 N·m | 71 in·lb | p. 528 |
| Ski nut | 47.5 ± 5.42 N·m | 35 ft·lb | p. 529 |
| Adjusting knob screw | 9 ± 1.02 N·m | 80 in·lb | p. 532 |
| Adjusting knob screw | 24.5 ± 3.5 N·m | p. 532 |
Capacidades
O ficheiro completo é enviado pelo bot.
| Item | Valor | Também | Página PDF |
|---|---|---|---|
| Fuel tank | 36 L | p. 603 |
Velas de ignição
O ficheiro completo é enviado pelo bot.
| Item | Valor | Também | Página PDF |
|---|---|---|---|
| Spark plug | 0.4 mm | p. 404 |
Intervalos de manutenção
O ficheiro completo é enviado pelo bot.
| Item | Valor | Também | Página PDF |
|---|---|---|---|
| Engine oil change | 2 years | p. 36 | |
| Drive chain service | 3 years | p. 36 | |
| Coolant change | 5 years | p. 36 | |
| Drive chain service | 500 km | p. 37 |
Obter o documento
O ficheiro completo é enviado pelo bot.
Abrir no Telegram — o bot localiza este documento pelo seu id de catálogo e envia o ficheiro.
Abrir no bot- Catálogo de peçasTodos os manuais