BRP Defender Mnaual Master 2020 Manuel de maintenance
BRP Defender Mnaual Master · 2020 · Manuel de maintenance · 1545 pages
Données techniques
Le fichier complet est envoyé par le bot.
Couple de serrage
Le fichier complet est envoyé par le bot.
| Article | Valeur | Aussi | Page PDF |
|---|---|---|---|
| Magnetic drain plug | 29.8 ± 1.36 N·m | 22 ft·lb | p. 22 |
| Oil filter cover screws | 10 ± 1 N·m | p. 23 | |
| Coolant drain plug | 10.1 ± 1.02 N·m | 89 in·lb | p. 25 |
| Radiator hose clamp | 3.1 ± 0.45 N·m | 27 in·lb | p. 25 |
| Drain plug | 7.5 ± 0.45 N·m | 66 in·lb | p. 29 |
| Filler plug | 16.5 ± 2.5 N·m | p. 30 | |
| Spark plug | 20.3 ± 1.36 N·m | 15 ft·lb | p. 30 |
| Drain plug | 2.7 ± 0.34 N·m | 24 in·lb | p. 31 |
| Drain plug | 100 ± 10 N·m | p. 31 | |
| Air filter housing screws | 10.1 ± 2.03 N·m | 89 in·lb | p. 51 |
| Heat shield clamps | 4 ± 0.45 N·m | 35 in·lb | p. 59 |
| Heat shield clamps | 9 ± 1 N·m | p. 59 | |
| Cylinder head pipe | 13 ± 1 N·m | p. 64 | |
| Retaining nuts | 13 ± 1.02 N·m | 115 in·lb | p. 64 |
| Exhaust clamp | 55.6 ± 8.13 N·m | 41 ft·lb | p. 64 |
| Exhaust clamp | 24.5 ± 3.5 N·m | p. 64 | |
| Muffler retaining nut | 24.4 ± 4.07 N·m | 18 ft·lb | p. 64 |
| Oil strainer cover screws | 10.1 ± 1.02 N·m | 89 in·lb | p. 75 |
| Oil pump cover screws | 10.1 ± 1.02 N·m | 89 in·lb | p. 80 |
| Reed valve retaining | 10 ± 1 N·m | p. 94 | |
| Water pump housing | 10 ± 1 N·m | p. 100 | |
| Central louver screw | 1.6 ± 0.45 N·m | 14 in·lb | p. 137 |
| Console screw | 5.5 ± 0.45 N·m | 49 in·lb | p. 139 |
| Heating unit retaining nut | 14 ± 1.02 N·m | 124 in·lb | p. 140 |
| Blower assembly screw | 3.1 ± 0.45 N·m | 27 in·lb | p. 142 |
| Button head screw | 3.1 ± 0.45 N·m | 27 in·lb | p. 146 |
| Button head screw | 4 ± 0.5 N·m | p. 146 | |
| Hexagonal screw | 4 ± 0.45 N·m | 35 in·lb | p. 146 |
| HVAC unit cover screws | 1.35 N·m | 12 in·lb | p. 158 |
| HVAC unit retaining nuts subsection | 5 ± 1.02 N·m | 44 in·lb | p. 160 |
| Blower retaining screws | 1.35 N·m | 12 in·lb | p. 161 |
| Heater valve retaining | 1.35 N·m | 12 in·lb | p. 162 |
| Gear clamp | 3 N·m | 27 in·lb | p. 162 |
| Evaporator screws | 1.35 N·m | 12 in·lb | p. 163 |
| Expansion valve | 4.5 N·m | 40 in·lb | p. 163 |
| M6 magneto cover | 10 ± 1 N·m | p. 173 | |
| Bearing cover screws | 24.4 ± 2.71 N·m | 18 ft·lb | p. 173 |
| Bearing cover screws | 25 ± 3 N·m | p. 173 | |
| Shaft for wear or damages | 35 ± 4 N·m | p. 176 | |
| Rotor retaining nut | 180 ± 10 N·m | p. 176 | |
| Moval of starter drive cover | 10 ± 1 N·m | p. 178 | |
| Starter mounting screws | 10.1 ± 1.02 N·m | 89 in·lb | p. 178 |
| Age regulator/rectifier | 10 ± 1 N·m | p. 185 | |
| Stator retaining screws | 4 ± 0.3 N·m | p. 186 | |
| Stator retaining screws | 10 ± 1 N·m | p. 186 | |
| Sprag clutch housing | 30 ± 2 N·m | p. 189 | |
| Starter mounting screw | 25 ± 3 N·m | p. 191 | |
| Starter mounting screw | 24.4 ± 2.71 N·m | 18 ft·lb | p. 191 |
| Starter solenoid | 6 ± 0.7 N·m | p. 191 | |
| Starter cable nut | 6 ± 0.68 N·m | 53 in·lb | p. 191 |
| Intake manifold | 20 ± 2 N·m | p. 194 | |
| Plenum retaining screws | 20.3 ± 2.71 N·m | 15 ft·lb | p. 197 |
| Intake socket screws | 2.5 ± 0.5 N·m | p. 197 | |
| Air filter housing clamp | 2.5 ± 0.45 N·m | 22 in·lb | p. 197 |
| Air filter housing clamp | 6 ± 0.7 N·m | p. 197 | |
| Intake socket screws | 6 ± 0.68 N·m | 53 in·lb | p. 197 |
| Pan head screw der head | 10.1 ± 1.02 N·m | 89 in·lb | p. 206 |
| Cylinder | 20.3 ± 1.36 N·m | 15 ft·lb | p. 210 |
| Valve cover retaining screws | 7 ± 0.8 N·m | p. 229 | |
| Spring preload | 20 ± 1 N·m | p. 235 | |
| M6 Cylinder head | 10 ± 1 N·m | p. 235 | |
| Ignition | 12 ± 1 N·m | p. 248 | |
| Chain tensioner plug | 4.5 ± 0.45 N·m | 40 in·lb | p. 276 |
| Camshaft Camshaft timing gear | 10 ± 1 N·m | p. 278 | |
| Timing chain guide | 10 ± 1 N·m | p. 280 | |
| Bearing screw | 10.1 ± 1.02 N·m | 89 in·lb | p. 280 |
| Balancer shaft ball bearing | 24.4 ± 2.71 N·m | 18 ft·lb | p. 307 |
| Kcase M6 retaining screws | 10 ± 1 N·m | p. 307 | |
| M8 crankcase screws | 25 ± 3 N·m | p. 331 | |
| CVT cover retaining | 7 ± 0.8 N·m | p. 343 | |
| CVT cover screws | 7 ± 0.79 N·m | 62 in·lb | p. 343 |
| Drive pulley screw counterclockwise | 100 ± 7 N·m | p. 353 | |
| Driven pulley screw | 20 ± 1 N·m | p. 360 | |
| CVT cover retaining | 6 ± 0.7 N·m | p. 366 | |
| GOVERNOR CUP PULLER screws (P/N 529 036 350) | 20.3 ± 1.36 N·m | 15 ft·lb | p. 369 |
| Drive pulley screw | 120 ± 8 N·m | p. 377 | |
| Pivot screws | 20.3 ± 1.36 N·m | 15 ft·lb | p. 382 |
| Cam screw | 35.3 ± 4.07 N·m | 26 ft·lb | p. 382 |
| Driven pulley screw | 70 ± 5 N·m | p. 383 | |
| Bayonet cap | 2 ± 0.23 N·m | 18 in·lb | p. 391 |
| Centrifugal lever lock | 5 ± 0.6 N·m | p. 402 | |
| Cam screw | 61 ± 6 N·m | p. 409 | |
| VSS retaining screw | 10 ± 1 N·m | p. 418 | |
| Protection plate retaining | 10 ± 1 N·m | p. 434 | |
| Actuator screws | 20 ± 2 N·m | p. 436 | |
| Allen set screw | 7 ± 1 N·m | p. 440 | |
| Coupling unit screws | 25 ± 3.5 N·m | p. 441 | |
| Coupling unit screws | 24.4 ± 4.07 N·m | 18 ft·lb | p. 441 |
| Gearbox | 10 ± 1 N·m | p. 444 |
Capacités
Le fichier complet est envoyé par le bot.
| Article | Valeur | Aussi | Page PDF |
|---|---|---|---|
| Engine oil | 2 L | p. 1498 | |
| Fuel tank | 40 L | p. 1500 |
Bougies d'allumage
Le fichier complet est envoyé par le bot.
| Article | Valeur | Aussi | Page PDF |
|---|---|---|---|
| HD5 | — | p. 17 | |
| HO2S | — | p. 43 | |
| M10 | — | p. 208 | |
| HD8 | — | p. 232 | |
| HD10 | — | p. 232 |
Intervalles d'entretien
Le fichier complet est envoyé par le bot.
| Article | Valeur | Aussi | Page PDF |
|---|---|---|---|
| Brake inspection | 2 years | p. 17 |
Obtenir le document
Le fichier complet est envoyé par le bot.
Ouvrir dans Telegram — le bot retrouve ce document par son identifiant de catalogue et envoie le fichier.
Ouvrir dans le bot- Manuels propriétaire BRP officiels et gratuitsCatalogue de piècesTous les manuels