BRP 2024 Manuel d'entretien
BRP · 2024 · Manuel d'entretien · 343 pages
Données techniques
Les valeurs ci-dessous ont été extraites automatiquement du document. Vérifiez-les dans le manuel d'origine avant de commander des pièces ou d'appliquer un couple de serrage.
Couple de serrage
Valeurs extraites du texte du document. Vérifiez-les dans l'original avant toute intervention d'entretien.
| Article | Valeur | Aussi | Page PDF |
|---|---|---|---|
| MAPTS screw | 7 ± 0.79 N·m | 62 in·lb | p. 30 |
| Intake manifold screws | 9 ± 1.02 N·m | 80 in·lb | p. 33 |
| Fuel rail screws | 9 ± 1.02 N·m | 80 in·lb | p. 33 |
| Clamping plate screws | 24.4 ± 2.71 N·m | 18 ft·lb | p. 36 |
| Exhaust manifold | 25 ± 3 N·m | p. 38 | |
| V-band clamps nuts | 9 ± 1.02 N·m | 80 in·lb | p. 38 |
| Magnetic drain plugs | 29.8 ± 2.71 N·m | 22 ft·lb | p. 49 |
| Avoid potential burns, never touch exhaust | 9 ± 1 N·m | p. 50 | |
| Oil filter cover screws | 9 ± 1.02 N·m | 80 in·lb | p. 50 |
| Oil filler tube screw | 7 ± 0.79 N·m | 62 in·lb | p. 52 |
| Line pressure sensor | 9 ± 1 N·m | p. 55 | |
| Cable clamp screws | 3.5 ± 0.23 N·m | 31 in·lb | p. 55 |
| Cable clamp screw | 3.5 ± 0.23 N·m | 31 in·lb | p. 56 |
| Oil pump screws | 9 ± 1 N·m | p. 63 | |
| Bearing bolt | 100 ± 7 N·m | p. 64 | |
| Oil sump cover screws | 9 ± 1 N·m | p. 65 | |
| Outlet socket screws | 9 ± 1.02 N·m | 80 in·lb | p. 71 |
| Water pump housing | 9 ± 1 N·m | p. 74 | |
| Water pump screws | 9 ± 1 N·m | 80 in·lb | p. 74 |
| Water duct cover | 9 ± 1 N·m | p. 75 | |
| Cylinder block | 9 ± 1 N·m | p. 75 | |
| Intermediate gear | 9 ± 1.02 N·m | 80 in·lb | p. 77 |
| CPS screw | 9 ± 1.02 N·m | 80 in·lb | p. 82 |
| Stator screws | 11 ± 0.79 N·m | 97 in·lb | p. 86 |
| Stator cable cover | 9 ± 1.02 N·m | 80 in·lb | p. 87 |
| Rotor nut | 400 ± 47.45 N·m | 295 ft·lb | p. 89 |
| Sprag clutch housing | 25 ± 3 N·m | p. 90 | |
| Starter screws | 9 ± 1.02 N·m | 80 in·lb | p. 92 |
| Starter cable nut | 6 ± 0.45 N·m | 53 in·lb | p. 92 |
| Engine bracket screws | 50.2 ± 5.42 N·m | 37 ft·lb | p. 92 |
| Camshaft locking tool | 4 ± 0.5 N·m | p. 97 | |
| Chain tension guide | 10 ± 1 N·m | p. 103 | |
| Bearing screws | 10.1 ± 1.02 N·m | 89 in·lb | p. 103 |
| Lower chain guide | 9 ± 1 N·m | p. 103 | |
| CAPS screw | 9 ± 0.56 N·m | 80 in·lb | p. 112 |
| Valve cover | 9 ± 1.02 N·m | 80 in·lb | p. 114 |
| Camshaft | 9 ± 1.02 N·m | 80 in·lb | p. 118 |
| Camshaft | 5 ± 0.5 N·m | p. 118 | |
| M6 cylinder head | 9 ± 1 N·m | p. 121 | |
| M10 studs (P/N 529036624) | 20.3 ± 1.36 N·m | 15 ft·lb | p. 122 |
| Square tube screws | 9 ± 1.02 N·m | 80 in·lb | p. 122 |
| Arrester screws | 11 ± 1.02 N·m | 97 in·lb | p. 123 |
| Chain cavity | 5 ± 0.6 N·m | p. 124 | |
| Crankshaft locking tool | 12 ± 2 N·m | p. 133 | |
| Knock sensor screw | 24.4 ± 2.71 N·m | 18 ft·lb | p. 135 |
| Engine stand adaptor plate | 12 ± 0.8 N·m | p. 137 | |
| Engine lifting hook | 12 ± 0.79 N·m | 106 in·lb | p. 137 |
| Engine stand adaptor | 25 ± 3 N·m | p. 137 | |
| M6 x 45 cylinder block | 9 ± 1 N·m | p. 145 | |
| M6 x 85 cylinder block | 9 ± 1 N·m | p. 145 | |
| Ring/Piston Groove Clearance Lower | 20.3 ± 1.36 N·m | 15 ft·lb | p. 159 |
| ECM adapter tool BPS screw (P/N 529036513) | 7 ± 0.79 N·m | 62 in·lb | p. 169 |
| Turbocharger screws | 24.4 ± 2.71 N·m | 18 ft·lb | p. 173 |
| Turbocharger screws | 25 ± 3 N·m | p. 173 | |
| Locknut | 7 ± 0.45 N·m | 62 in·lb | p. 176 |
| Counter nut | 9 ± 1.02 N·m | 80 in·lb | p. 178 |
| Hydraulic housing | 15 ± 2 N·m | p. 208 | |
| Drain plug | 15 ± 2.03 N·m | 133 in·lb | p. 208 |
| Filter cover screws | 11 ± 1.02 N·m | 97 in·lb | p. 209 |
| Gearbox drain plugs | 29.8 ± 2.71 N·m | 22 ft·lb | p. 209 |
| Level plug | 5 ± 0.56 N·m | 44 in·lb | p. 210 |
| Connecting flange nuts | 40.7 ± 4.07 N·m | 30 ft·lb | p. 216 |
| Speed sensor screw | 11 ± 1.02 N·m | 97 in·lb | p. 224 |
| Magnet screw | 2.7 ± 0.23 N·m | 24 in·lb | p. 227 |
| GBPS screw | 11 ± 1.02 N·m | 97 in·lb | p. 228 |
| Connector pin | 11 ± 1 N·m | p. 228 | |
| Protective cover screw | 11 ± 1.02 N·m | 97 in·lb | p. 228 |
| Park switch | 2 ± 0.23 N·m | 18 in·lb | p. 229 |
| Cable clamp screw | 2 ± 0.23 N·m | 18 in·lb | p. 234 |
| Actuator screws | 11 ± 1.02 N·m | 97 in·lb | p. 234 |
| Actuator screw | 8 ± 1.02 N·m | 71 in·lb | p. 236 |
| Oil seal installer | 11 ± 1 N·m | p. 238 | |
| Actuator cover screw | 11 ± 1.02 N·m | 97 in·lb | p. 238 |
| SFS screws | 2.7 ± 0.23 N·m | 24 in·lb | p. 240 |
| ECM adapter pin | 22 ± 2 N·m | p. 242 | |
| Pin | 1.8 ± 0.11 N·m | 16 in·lb | p. 244 |
| Hydraulic housing | 2.7 ± 0.2 N·m | p. 249 | |
| Solenoid valve screws | 2.7 ± 0.23 N·m | 24 in·lb | p. 249 |
| Hydraulic valve cover | 15 ± 2 N·m | p. 251 | |
| Hydraulic valve cover | 11 ± 1 N·m | p. 251 | |
| ECM screws | 2.1 ± 0.23 N·m | 19 in·lb | p. 257 |
| Clamp | 7 ± 0.45 N·m | 62 in·lb | p. 272 |
| Cable clamp screw | 9 ± 1 N·m | p. 279 | |
| Intake manifold screw | 9 ± 1.02 N·m | 80 in·lb | p. 280 |
| Ignition coil screw | 9 ± 1.02 N·m | 80 in·lb | p. 290 |
| Spark Plug | 14 ± 1 N·m | p. 291 | |
| Wheel lug nuts | 120.7 ± 5.42 N·m | 89 ft·lb | p. 313 |
Obtenir le document
Le fichier complet est envoyé par le bot. Les guides propriétaire gratuits pour BRP sont également disponibles auprès du fabricant.
Ouvrir dans Telegram — le bot retrouve ce document par son identifiant de catalogue et envoie le fichier.
Ouvrir dans le bot- Manuels propriétaire BRP officiels et gratuitsCatalogue de piècesTous les manuels