Ski-Doo Supplement 2019 Manuel
Ski-Doo Supplement · 2019 · Manuel · 1746 pages
Données techniques
Le fichier complet est envoyé par le bot.
Couple de serrage
Le fichier complet est envoyé par le bot.
| Article | Valeur | Aussi | Page PDF |
|---|---|---|---|
| Spark plug I | 18 ± 0.7 N·m | p. 39 | |
| Brake caliper bleeder I | 8.5 ± 1.5 N·m | p. 44 | |
| Exhaust manifold screws I | 34 ± 4 N·m | p. 54 | |
| Muffler retaining screw | 7 ± 1.02 N·m | 62 in·lb | p. 59 |
| Exhaust Gas | 45 ± 2 N·m | p. 61 | |
| Temperature Sensor | 44.7 ± 1.36 N·m | 33 ft·lb | p. 61 |
| Coolant hose clamp | 3.1 ± 0.45 N·m | 27 in·lb | p. 91 |
| Bearing carrier screws I | 5 ± 0.3 N·m | p. 95 | |
| Magneto housing | 6 ± 0.4 N·m | p. 105 | |
| Lighten stator retaining screws | 10 ± 0.7 N·m | p. 108 | |
| Collar nuts I | 4 ± 0.3 N·m | p. 127 | |
| RAVE valve housing | 10 ± 0.7 N·m | p. 127 | |
| Rave cable lock nut I | 20 ± 2 N·m | p. 129 | |
| Bracket | 20.3 ± 1.36 N·m | 15 ft·lb | p. 129 |
| Bracket retaining screws | 11 ± 0.79 N·m | 97 in·lb | p. 131 |
| Bracket retaining screws | 4 ± 1 N·m | p. 131 | |
| Reed valve blade screws I | 1.5 ± 0.3 N·m | p. 135 | |
| Under screw head | 50 ± 1.5 N·m | p. 141 | |
| MS Crankcase screws I | 29 ± 2 N·m | p. 154 | |
| 219100912-014-009 M6 Crankcase screws I | 11 ± 0.8 N·m | p. 154 | |
| Head | 5.5 ± 0.5 N·m | p. 204 | |
| Water pump cover screws | 11 ± 0.79 N·m | 97 in·lb | p. 209 |
| Coolant hose clamp I | 3 ± 0.4 N·m | p. 209 | |
| Screws I | 6 ± 0.45 N·m | 53 in·lb | p. 223 |
| Lighten CPS retaining screws | 8 ± 0.45 N·m | 71 in·lb | p. 224 |
| Starter mounting screws I | 11 ± 0.8 N·m | p. 228 | |
| Clamps | 4 ± 0.3 N·m | p. 245 | |
| Collar nuts | 4 ± 0.3 N·m | 35 in·lb | p. 245 |
| Collar nuts | 10 ± 0.7 N·m | 89 in·lb | p. 245 |
| Intake adapter retaining | 6 ± 0.4 N·m | p. 253 | |
| Reed valve blade screw s I | 1.5 ± 0.3 N·m | p. 253 | |
| Cylinder head screws I | 28 ± 1 N·m | p. 256 | |
| Cylinder block screws I | 50 ± 1.5 N·m | p. 259 | |
| Oil seal cover screws I | 11 ± 0.8 N·m | p. 274 | |
| Fuel hose retainer screw I | 5 N·m | 44 in·lb | p. 313 |
| Throttle body clamps I | 1.5 ± 0.2 N·m | p. 319 | |
| Adapter plate clamps I | 0.7 ± 0.1 N·m | p. 320 | |
| TPS retaining screw I | 4 ± 0.5 N·m | p. 322 | |
| Fuel injector retaining screws alter | 40 ± 1 N·m | 30 ft·lb | p. 347 |
| Fuel rail retaining screw s I | 8 ± 0.5 N·m | p. 353 | |
| Ignition coil retaining | 2.4 ± 0.2 N·m | p. 398 | |
| Lighten Absolute CPS screws | 2.5 ± 0.34 N·m | 22 in·lb | p. 418 |
| Retaining nuts | 5 ± 0.45 N·m | 44 in·lb | p. 421 |
| Ground cable screw I | 8 ± 0.5 N·m | p. 429 | |
| Knock sensor screw I | 24 ± 1 N·m | p. 431 | |
| Ground cable screw | 8 ± 0.45 N·m | 71 in·lb | p. 439 |
| Drive belt guard support | 7.5 ± 1 N·m | p. 446 | |
| Torx screw | 7.5 ± 1.02 N·m | 66 in·lb | p. 446 |
| Elastic nut | 10.1 ± 2.03 N·m | 89 in·lb | p. 446 |
| Clamping screw I | 5.5 ± 0.45 N·m | 49 in·lb | p. 447 |
| Roller axle screw | 5 ± 0.45 N·m | 44 in·lb | p. 461 |
| Damper screws | 5 ± 3.5 N·m | p. 462 | |
| Damper screws | 31.2 ± 4.07 N·m | 23 ft·lb | p. 462 |
| Cam screw | 5 ± 3.5 N·m | p. 471 | |
| Cam screw | 31.2 ± 4.07 N·m | 23 ft·lb | p. 471 |
| Bearing flange nut I | 15.5 ± 1.5 N·m | p. 472 | |
| Brake pad pin I | 10 ± 2 N·m | p. 478 | |
| Caliper screws | 24.4 ± 4.07 N·m | 18 ft·lb | p. 481 |
| Washers | 35 ± 1 N·m | p. 481 | |
| Brake lever pivot nut I | 6 ± 1 N·m | p. 482 | |
| Master cylinder clamp screws I | 9 ± 1 N·m | 80 in·lb | p. 482 |
| Middle clamp nut | 2.3 ± 0.2 N·m | p. 484 | |
| Middle clamp nut | 35 ± 1 N·m | p. 484 | |
| Caliper Banjo fitting | 35.3 ± 1.36 N·m | 26 ft·lb | p. 484 |
| Master cylinder Banjo | 27 ± 1 N·m | p. 484 | |
| Caliper Banjo fitting | 27.1 ± 1.36 N·m | 20 ft·lb | p. 484 |
| Drain plug I | 6 ± 1 N·m | p. 489 | |
| Bearing | 24.5 ± 3.5 N·m | p. 495 | |
| Front arm bolts | 47.5 ± 5.42 N·m | 35 ft·lb | p. 516 |
| Rear arm connecting | 61 ± 9 N·m | p. 516 | |
| Rod screws | 61 ± 9.49 N·m | 45 ft·lb | p. 516 |
| Clamp screws | 2.5 ± 0.45 N·m | 22 in·lb | p. 517 |
| Clamp screws | 0.4 ± 0.1 N·m | p. 517 | |
| Knob screw | 0.5 ± 0.11 N·m | 4 in·lb | p. 517 |
| Support screws | 5 ± 1.02 N·m | 44 in·lb | p. 519 |
| Support screws | 2.5 ± 0.5 N·m | p. 519 | |
| Clamp screws | 1.5 ± 0.5 N·m | p. 519 | |
| Banjo bolt | 24.5 ± 3.5 N·m | p. 522 | |
| Upper bolts I | 48 ± 6 N·m | p. 542 | |
| Front and rear arm | 47.5 ± 5.42 N·m | 35 ft·lb | p. 542 |
| Rear shock absorber | 24.5 ± 3.5 N·m | p. 545 | |
| Center shock absorber | 40 ± 5 N·m | p. 546 | |
| Spring retaining nuts I | 24.5 ± 3.5 N·m | p. 558 | |
| Hook retaining nut I | 9 ± 3 N·m | p. 559 | |
| Hook retaining nut | 9 ± 3.05 N·m | 80 in·lb | p. 559 |
| Pivot arm lower nut | 24.4 ± 4.07 N·m | 18 ft·lb | p. 568 |
| Pivot arm lower nut | 32 ± 4 N·m | p. 568 | |
| Pivot arm upper nut | 32.5 ± 4.07 N·m | 24 ft·lb | p. 568 |
| SCM retaining nut | 2.5 ± 0.5 N·m | p. 579 | |
| Jam nut I | 18.5 ± 3.5 N·m | p. 591 | |
| Runner nut | 8 ± 1.02 N·m | 71 in·lb | p. 592 |
| Ski nut | 47.5 ± 5.42 N·m | 35 ft·lb | p. 593 |
| Adjusting knob screw | 9 ± 1 N·m | p. 596 | |
| Adjusting knob screw | 24.5 ± 3.5 N·m | p. 596 | |
| Indicator screw | 24.4 ± 4.07 N·m | 18 ft·lb | p. 596 |
Capacités
Le fichier complet est envoyé par le bot.
| Article | Valeur | Aussi | Page PDF |
|---|---|---|---|
| Fuel tank | 36 L | p. 646 |
Bougies d'allumage
Le fichier complet est envoyé par le bot.
| Article | Valeur | Aussi | Page PDF |
|---|---|---|---|
| Spark plug | 0.6 mm | p. 645 | |
| D01 | — | p. 888 | |
| Y18-008 | — | p. 1134 | |
| Y18-011 | — | p. 1202 |
Intervalles d'entretien
Le fichier complet est envoyé par le bot.
| Article | Valeur | Aussi | Page PDF |
|---|---|---|---|
| Drive chain service | 500 km | p. 691 | |
| Coolant change | 5 years | p. 692 | |
| Drive chain service | 1500 km | p. 1230 |
Obtenir le document
Le fichier complet est envoyé par le bot.
Ouvrir dans Telegram — le bot retrouve ce document par son identifiant de catalogue et envoie le fichier.
Ouvrir dans le bot- Catalogue de piècesTous les manuels