Ski-Doo Renegade 2019 Manuel d'entretien
Ski-Doo Renegade · 2019 · Manuel d'entretien · 1636 pages
Données techniques
Le fichier complet est envoyé par le bot.
Couple de serrage
Le fichier complet est envoyé par le bot.
| Article | Valeur | Aussi | Page PDF |
|---|---|---|---|
| Drain plug | 10 N·m | 89 in·lb | p. 31 |
| Filter cover screw | 3 N·m | 27 in·lb | p. 36 |
| Brake caliper bleeder | 9 N·m | 80 in·lb | p. 39 |
| Pivot screw brake lever | 6 N·m | 53 in·lb | p. 40 |
| Gearbox drain plug | 8 N·m | 71 in·lb | p. 40 |
| Oil level check plug | 10 N·m | 89 in·lb | p. 41 |
| Engine rubber mount | 24.5 ± 3.5 N·m | p. 55 | |
| Engine support screws | 42 ± 4.07 N·m | 31 ft·lb | p. 56 |
| Front Engine Support Replacement | 42 ± 4 N·m | p. 57 | |
| ENGINE RUBBER MOUNTS Engine rubber mount | 10 ± 2 N·m | p. 58 | |
| Engine support screws | 31.2 ± 4.07 N·m | 23 ft·lb | p. 64 |
| Throttle body screws | 9 ± 1 N·m | p. 74 | |
| Intake manifold screws | 9 ± 1 N·m | p. 74 | |
| Exhaust manifold nuts | 15 N·m | 133 in·lb | p. 86 |
| Muffler retaining screw | 7 ± 1.02 N·m | 62 in·lb | p. 90 |
| Throttle body screws | 0.9 ± 0.1 N·m | p. 96 | |
| Clamp | 0.9 ± 0.11 N·m | 8 in·lb | p. 96 |
| Regulator plug | 17 ± 2 N·m | p. 109 | |
| Washers | 15 ± 2 N·m | p. 117 | |
| Oil filter cover PRESSURE GAUGE | 9 ± 1.02 N·m | 80 in·lb | p. 124 |
| Oil filler tube screw | 9 ± 1.02 N·m | 80 in·lb | p. 128 |
| Drain plug | 15 ± 2.03 N·m | 133 in·lb | p. 139 |
| Drain plugs regulations | 15 ± 2.03 N·m | 133 in·lb | p. 145 |
| Oil filter cover screws | 9 ± 1.02 N·m | 80 in·lb | p. 146 |
| Oil filler tube screw | 7 ± 0.79 N·m | 62 in·lb | p. 150 |
| Cylinder | 11 ± 1.02 N·m | 97 in·lb | p. 160 |
| From throttle | 1.2 ± 0.2 N·m | p. 163 | |
| Press retaining screws | 9 ± 1.02 N·m | 80 in·lb | p. 186 |
| Water pump drive gear | 9 ± 1 N·m | p. 187 | |
| Turbo engine | 2.5 ± 0.5 N·m | p. 190 | |
| Drain screws | 9 ± 1 N·m | p. 192 | |
| Housing screws | 29.8 ± 1.36 N·m | 22 ft·lb | p. 216 |
| Starter cable nut | 7 ± 1.02 N·m | 62 in·lb | p. 219 |
| Magneto cover screws REQUIRED TOOL | 9 ± 1.02 N·m | 80 in·lb | p. 223 |
| Sprag clutch housing | 30 ± 2 N·m | p. 228 | |
| Starter retaining screws | 9 ± 1 N·m | p. 231 | |
| Screw plug timing chain | 17 ± 2 N·m | p. 246 | |
| Oil sump cover | 50 ± 3 N·m | p. 247 | |
| Valve cover | 9 ± 1.02 N·m | 80 in·lb | p. 281 |
| Camshaft | 5 ± 0.5 N·m | p. 284 | |
| Holder screws | 5 ± 0.45 N·m | 44 in·lb | p. 284 |
| Cylinder head | 9 ± 1 N·m | p. 290 | |
| Cylinder head | 20.3 ± 1.36 N·m | 15 ft·lb | p. 290 |
| Exhaust camshaft timing gear | 9 ± 1.02 N·m | 80 in·lb | p. 306 |
| PTO cover screws | 23 ± 2.71 N·m | 17 ft·lb | p. 345 |
| Cylinder block | 20 ± 2 N·m | p. 350 | |
| M9 screws | 20.3 ± 1.36 N·m | 15 ft·lb | p. 350 |
| Cylinder block | 23 ± 2 N·m | p. 350 | |
| Cylinder block | 9 ± 1 N·m | p. 351 | |
| Rod screws | 12 ± 2.03 N·m | 106 in·lb | p. 361 |
| Timing chain tensioner | 23 ± 3 N·m | p. 369 | |
| Banjo bolts | 8 N·m | 71 in·lb | p. 397 |
| Banjo bolts | 15.75 ± 0.75 N·m | p. 397 | |
| Clamp | 2.2 ± 0.2 N·m | p. 398 | |
| Clamp | 2.1 ± 0.23 N·m | 19 in·lb | p. 398 |
| ECM screw | 2.5 ± 0.45 N·m | 22 in·lb | p. 480 |
| Fuel rail retaining screw | 9 ± 1.02 N·m | 80 in·lb | p. 487 |
| O-ring | 9 ± 1 N·m | p. 494 | |
| CPS retaining screw | 9 ± 1.02 N·m | 80 in·lb | p. 494 |
| MAPTS retaining screw | 4.5 ± 0.45 N·m | 40 in·lb | p. 499 |
| BPS retaining screw | 4.5 ± 0.5 N·m | p. 501 | |
| Turn ignition key | 4.5 ± 0.45 N·m | 40 in·lb | p. 501 |
| Knock sensor screw | 24 ± 3 N·m | p. 503 | |
| Oxygen sensor | 55.6 ± 5.42 N·m | 41 ft·lb | p. 506 |
| Engine Ground | 31.2 ± 4.07 N·m | 23 ft·lb | p. 547 |
| Engine Cut-Off Switch Continuity Test | 9 ± 1 N·m | p. 575 | |
| Ignition coil retaining | 9 ± 1 N·m | p. 584 | |
| Spark plug | 13 ± 1.02 N·m | 115 in·lb | p. 584 |
| Battery holder screw | 7 ± 1.02 N·m | 62 in·lb | p. 589 |
| Battery terminals | 10 ± 2 N·m | p. 594 | |
| Battery hold down | 5 ± 0.5 N·m | p. 594 | |
| Bracket | 5 ± 0.45 N·m | 44 in·lb | p. 594 |
| Battery cover retaining | 7 ± 1 N·m | p. 594 | |
| Solenoid cable retaining (P/N 293 550 004) | 4 ± 0.5 N·m | p. 604 | |
| Taillight retaining screw | 0.8 ± 0.23 N·m | 7 in·lb | p. 611 |
| Gauge retaining screws | 1 ± 0.23 N·m | 9 in·lb | p. 623 |
Capacités
Le fichier complet est envoyé par le bot.
| Article | Valeur | Aussi | Page PDF |
|---|---|---|---|
| Fuel tank | 45 L | p. 966 | |
| Fuel tank | 40 L | p. 967 | |
| Fuel tank | 36 L | p. 970 |
Bougies d'allumage
Le fichier complet est envoyé par le bot.
| Article | Valeur | Aussi | Page PDF |
|---|---|---|---|
| MR7BI-8 | — | p. 37 | |
| M14 | — | p. 322 | |
| Spark plug | 0.4 mm | p. 741 | |
| MR8BI-8 | — | p. 966 | |
| MR7BI | — | p. 1306 |
Intervalles d'entretien
Le fichier complet est envoyé par le bot.
| Article | Valeur | Aussi | Page PDF |
|---|---|---|---|
| Coolant change | 5 years | p. 26 | |
| Engine oil change | 2 years | p. 28 | |
| Spark plug service | 5 years | p. 1276 | |
| Drive chain service | 3 years | p. 1537 |
Obtenir le document
Le fichier complet est envoyé par le bot.
Ouvrir dans Telegram — le bot retrouve ce document par son identifiant de catalogue et envoie le fichier.
Ouvrir dans le bot- Catalogue de piècesTous les manuels