BRP M Buds2 Discount Manual
BRP M Buds2 Discount · manual · 585 pages
Technical data
Numbers below were extracted automatically from the document. Verify them against the original manual before you order parts or apply torque.
Tightening torque
Values extracted from the document text. Check against the original before service work.
| Item | Value | Also | PDF page |
|---|---|---|---|
| INJECTION (EFI) Engine | 10 ± 1 N·m | p. 14 | |
| Intake Manifold | 9 ± 1 N·m | p. 15 | |
| Intake manifold | 20 ± 2 N·m | p. 19 | |
| Retaining screws | 20.3 ± 1.36 N·m | 15 ft·lb | p. 19 |
| Intake socket clamp | 0.7 ± 0.11 N·m | 6 in·lb | p. 19 |
| Oil strainer screws | 6 ± 0.68 N·m | 53 in·lb | p. 30 |
| Cooling System - Engine Components | 3.5 ± 0.4 N·m | p. 34 | |
| Molycote CYLINDER BLOCK | 2.5 ± 0.3 N·m | p. 34 | |
| Thermostat cover | 6 ± 0.7 N·m | p. 36 | |
| Magneto and Starter | 6 ± 0.68 N·m | 53 in·lb | p. 47 |
| CPS retaining screw | 10.1 ± 1.02 N·m | 89 in·lb | p. 49 |
| Stator screws | 10 ± 1 N·m | p. 51 | |
| Holding strip screws | 4 ± 0.45 N·m | 35 in·lb | p. 51 |
| Nu Rotor screw | 150.5 ± 9.49 N·m | 111 ft·lb | p. 53 |
| Sprag clutch housing | 30 ± 2 N·m | p. 54 | |
| Magneto and Starter | 25 ± 3 N·m | p. 57 | |
| Retaining nut | 6 ± 0.45 N·m | 53 in·lb | p. 57 |
| Timing Chain | 4.5 ± 0.5 N·m | p. 59 | |
| NOTICE Chain tensioner plug | 4.5 ± 0.45 N·m | 40 in·lb | p. 62 |
| Retaining screws | 10.1 ± 1.02 N·m | 89 in·lb | p. 64 |
| Timing chain guide | 10 ± 1 N·m | p. 69 | |
| Bearing screw | 10.1 ± 1.02 N·m | 89 in·lb | p. 69 |
| Cylinder Head | 7 ± 0.79 N·m | 62 in·lb | p. 71 |
| Cylinder Head | 12 ± 1 N·m | p. 72 | |
| Knock sensor | 20 ± 3 N·m | p. 78 | |
| Mounting screw | 20.3 ± 2.71 N·m | 15 ft·lb | p. 78 |
| Valve Cover Access | 7 ± 0.8 N·m | p. 78 | |
| Brp screws | 7 ± 0.79 N·m | 62 in·lb | p. 78 |
| Cylinder Head | 20 ± 1 N·m | p. 85 | |
| M10 cylinder | 20.3 ± 1.36 N·m | 15 ft·lb | p. 85 |
| Rear bearing cover | 10 ± 1 N·m | p. 104 | |
| Brp PTO cover screws | 10 ± 1 N·m | p. 108 | |
| M8 crankcase screws | 24.4 ± 2.71 N·m | 18 ft·lb | p. 114 |
| M6 crankcase screws | 10.1 ± 1.02 N·m | 89 in·lb | p. 114 |
| CVT cover screws | 7 ± 0.79 N·m | 62 in·lb | p. 128 |
| Threaded stud | 50.2 ± 1.36 N·m | 37 ft·lb | p. 142 |
| Continuously Variable Transmission | 65 ± 2 N·m | p. 143 | |
| Stud | 44.7 ± 1.36 N·m | 33 ft·lb | p. 152 |
| NOTICE Counter nut | 35.3 ± 1.36 N·m | 26 ft·lb | p. 155 |
| Distance between counter nut | 20 ± 1 N·m | p. 155 | |
| Reading VSS screws | 10.1 ± 1.02 N·m | 89 in·lb | p. 165 |
| Indicator switch | 2.5 ± 0.34 N·m | 22 in·lb | p. 166 |
| Actuator screw | 25 ± 3 N·m | p. 169 | |
| Actuator screw | 24.4 ± 2.71 N·m | 18 ft·lb | p. 169 |
| M8 screws | 25 ± 3 N·m | p. 176 | |
| Right housing a feeler gauge | 24.4 ± 2.71 N·m | 18 ft·lb | p. 176 |
| Loctite chisel (gasket remover) Gear housing | 10.1 ± 1.02 N·m | 89 in·lb | p. 191 |
| Gearbox nuts nu | 25 ± 3 N·m | 18 ft·lb | p. 192 |
| GBPS screws | 10.1 ± 1.02 N·m | 89 in·lb | p. 200 |
| Actuator screws | 24.4 ± 2.71 N·m | 18 ft·lb | p. 202 |
| Left cover - M6 screws | 10.1 ± 1.02 N·m | 89 in·lb | p. 216 |
| Gearbox nuts | 25 ± 3 N·m | p. 217 | |
| Gearbox nuts | 24.4 ± 2.71 N·m | 18 ft·lb | p. 217 |
| Fuel rail screws | 10 ± 1 N·m | p. 237 | |
| Throttle body screws | 7.5 ± 0.5 N·m | p. 238 | |
| Tail pipe retaining screws | 11 ± 1 N·m | p. 325 | |
| Oil filter cover screws | 10.1 ± 1.02 N·m | 89 in·lb | p. 328 |
| Coolant drain plug | 10.1 ± 1.02 N·m | 89 in·lb | p. 331 |
| Bleed screws | 5 ± 0.56 N·m | 44 in·lb | p. 331 |
| Magnetic drain plug | 20 ± 2 N·m | p. 333 | |
| Oil level plug | 5 ± 0.56 N·m | 44 in·lb | p. 333 |
| Spark plug | 20.3 ± 1.36 N·m | 15 ft·lb | p. 337 |
| ELECTRICAL SYSTEM m Spark plug | 11 ± 1 N·m | p. 337 | |
| Filler plug | 22.5 ± 2.5 N·m | p. 337 | |
| Filler plug | 23 ± 2.71 N·m | 17 ft·lb | p. 337 |
| Drain plug | 7.5 ± 0.5 N·m | p. 339 | |
| Wheel lug nuts | 80 ± 5.42 N·m | 59 ft·lb | p. 339 |
| Intake manifold | 6 ± 0.7 N·m | p. 351 | |
| MAPTS retaining screw | 6 ± 0.68 N·m | 53 in·lb | p. 351 |
| Gasket ring | 30 ± 2 N·m | p. 358 | |
| Water pump housing | 10 ± 1 N·m | p. 370 | |
| Regulator/rectifier | 25 ± 3 N·m | p. 382 | |
| Bearing cover screws | 24.4 ± 2.71 N·m | 18 ft·lb | p. 382 |
| Shaft for wear or damages | 35 ± 4 N·m | p. 385 | |
| Rotor retaining nut | 180 ± 10 N·m | p. 385 | |
| Starter mounting screws | 10 ± 1 N·m | p. 387 | |
| Camshaft timing gear and timing chain | 10.1 ± 1.02 N·m | 89 in·lb | p. 399 |
| Nu PAN HEAD SCREW | 10 ± 1 N·m | p. 412 | |
| Counter Shaft (PTO side) Ball Bearing | 24.4 ± 2.71 N·m | 18 ft·lb | p. 441 |
| Retaining screws | 7 ± 0.79 N·m | 62 in·lb | p. 453 |
| Drive pulley screw counterclockwise | 100 ± 7 N·m | p. 463 | |
| VSS retaining screw | 10 ± 1 N·m | p. 476 | |
| Throttle body retaining | 10 ± 1.2 N·m | p. 515 | |
| Ignition coil retaining bolt | 8 ± 1 N·m | p. 521 | |
| Protective plate | 10 ± 1 N·m | p. 550 | |
| Actuator screws | 20 ± 2 N·m | p. 552 | |
| Allen set screw | 7 ± 1.02 N·m | 62 in·lb | p. 556 |
Spark plugs
Values extracted from the document text. Check against the original before service work.
| Item | Value | Also | PDF page |
|---|---|---|---|
| M10 | — | p. 83 | |
| MG1 | — | p. 521 | |
| Spark plug | 0.7 mm | p. 529 |
Get the document
The full file is delivered by the bot. Free owner guides for BRP are also available from the manufacturer.
Open in Telegram — the bot finds this document by its catalog id and sends the file.
Open in bot- Official free BRP owner's manualsParts catalogueAll manuals