Ski-Doo Summit 2021 Service
Ski-Doo Summit · 2021 · service manual · 1084 pages
Technical data
Numbers below were extracted automatically from the document. Verify them against the original manual before you order parts or apply torque.
Tightening torque
Values extracted from the document text. Check against the original before service work.
| Item | Value | Also | PDF page |
|---|---|---|---|
| Coolant hose clamp | 3.1 ± 0.45 N·m | 27 in·lb | p. 20 |
| Spark plug | 18 ± 0.68 N·m | 159 in·lb | p. 23 |
| Rear idler wheel | 47.5 ± 5.42 N·m | 35 ft·lb | p. 26 |
| Brake caliper bleeder | 8.5 ± 1.47 N·m | 75 in·lb | p. 28 |
| INTAKE SYSTEM subsection | 31.2 ± 4.07 N·m | 23 ft·lb | p. 42 |
| Snug all bolts | 33 ± 3 N·m | p. 42 | |
| M5 Torx screw | 1.8 ± 0.2 N·m | p. 65 | |
| 219101031-002-016 panel nut | 1.8 ± 0.23 N·m | 16 in·lb | p. 65 |
| Muffler retaining screw | 7 ± 1.02 N·m | 62 in·lb | p. 70 |
| Exhaust Gas | 45 ± 2 N·m | p. 75 | |
| Temperature Sensor | 44.7 ± 1.36 N·m | 33 ft·lb | p. 75 |
| Exhaust pipe | 28 ± 1 N·m | p. 80 | |
| Oetiker clamp | 1.7 ± 0.2 N·m | p. 83 | |
| ETS retaining screw | 1.7 ± 0.23 N·m | 15 in·lb | p. 83 |
| Exhaust manifold screws | 33.9 ± 4.07 N·m | 25 ft·lb | p. 86 |
| Transmission | 15 ± 1 N·m | p. 117 | |
| Cylinder | 5.5 ± 0.5 N·m | p. 118 | |
| Head | 5.5 ± 0.45 N·m | 49 in·lb | p. 118 |
| Water pump cover screws | 11 ± 0.79 N·m | 97 in·lb | p. 123 |
| Bearing carrier screws | 5 ± 0.34 N·m | 44 in·lb | p. 127 |
| Retaining screw | 125 ± 9 N·m | p. 153 | |
| Magneto housing | 7 ± 0.5 N·m | p. 154 | |
| CPS retaining screws | 8 ± 0.45 N·m | 71 in·lb | p. 155 |
| Starter mounting screws | 11 ± 0.79 N·m | 97 in·lb | p. 160 |
| Retaining nut | 4 ± 0.3 N·m | p. 173 | |
| RAVE valve housing | 10 ± 0.7 N·m | p. 177 | |
| Collar nuts | 4 ± 0.34 N·m | 35 in·lb | p. 178 |
| Bracket | 20 ± 2 N·m | p. 179 | |
| RAVE cable lock nut | 20.3 ± 1.36 N·m | 15 ft·lb | p. 179 |
| Counter nut | 20 ± 2 N·m | p. 179 | |
| Snap ring | 20.3 ± 1.36 N·m | 15 ft·lb | p. 179 |
| RAVE cable lock nut | 5 ± 0.6 N·m | p. 179 | |
| Retaining plate screw | 5 ± 0.56 N·m | 44 in·lb | p. 179 |
| Bracket retaining screws | 11 ± 0.8 N·m | p. 181 | |
| Reed valve blade screws | 1.5 ± 0.34 N·m | 13 in·lb | p. 185 |
| Intake adapter retaining | 1.5 ± 0.3 N·m | p. 185 | |
| Intake adapter retaining | 6 ± 0.4 N·m | p. 185 | |
| Cylinder head screws | 30 ± 2 N·m | p. 188 | |
| Under screw head | 50 ± 1.5 N·m | p. 191 | |
| SERVICE PRODUCT Cylinder block screws | 50.2 ± 1.36 N·m | 37 ft·lb | p. 191 |
| Reed valve blade screws | 6 ± 0.45 N·m | 53 in·lb | p. 202 |
| Cylinder head screws | 28 ± 1 N·m | p. 205 | |
| Crankcase screws | 30 ± 2 N·m | p. 219 | |
| Oil seal cover screws | 11 ± 0.79 N·m | 97 in·lb | p. 220 |
| M8 Crankcase screws | 28.5 ± 1.36 N·m | 21 ft·lb | p. 233 |
| Oil catch tank screw | 7.5 ± 1.02 N·m | 66 in·lb | p. 253 |
| Oil pump screw | 1.8 ± 0.23 N·m | 16 in·lb | p. 254 |
| Retaining screws | 24.4 ± 1.36 N·m | 18 ft·lb | p. 260 |
| Tridon clamp | 1.7 ± 0.23 N·m | 15 in·lb | p. 303 |
| Fuel hose retainer screw | 5 N·m | 44 in·lb | p. 332 |
| Tainer screw | 5 N·m | 44 in·lb | p. 332 |
| Fuel rail retaining screws | 8 ± 0.45 N·m | 71 in·lb | p. 337 |
| Adapter plate clamps | 0.7 ± 0.1 N·m | p. 343 | |
| Throttle body clamps | 1.5 ± 0.23 N·m | 13 in·lb | p. 343 |
| TPS retaining screw | 4 ± 0.45 N·m | 35 in·lb | p. 345 |
| MAPTS retaining screw | 4.5 ± 0.5 N·m | p. 348 | |
| M6 screw on chassis | 10 ± 2 N·m | p. 355 | |
| Spark plug | 17.5 ± 1.02 N·m | 155 in·lb | p. 380 |
| Ignition coil retaining | 2.4 ± 0.2 N·m | p. 383 | |
| Battery terminals | 10 ± 2 N·m | p. 387 | |
| Battery hold down | 5 ± 0.5 N·m | p. 387 | |
| Bracket | 5 ± 0.45 N·m | 44 in·lb | p. 387 |
| Battery cover retaining | 7 ± 1 N·m | p. 387 | |
| Solenoid cable retaining | 4 ± 0.5 N·m | p. 398 | |
| Absolute CPS screws | 2.5 ± 0.3 N·m | p. 406 | |
| MAGNETO AND STARTER subsections | 5 ± 0.5 N·m | p. 409 | |
| Retaining nuts | 5 ± 0.45 N·m | 44 in·lb | p. 409 |
| Ground cable screw | 8 ± 0.45 N·m | 71 in·lb | p. 417 |
| Knock sensor screw | 24 ± 1 N·m | p. 419 | |
| Taillight retaining screw | 0.8 ± 0.23 N·m | 7 in·lb | p. 437 |
| Retaining screws | 1 ± 0.23 N·m | 9 in·lb | p. 441 |
| Torx screw | 7.5 ± 1.02 N·m | 66 in·lb | p. 453 |
| Elastic nut | 10.1 ± 2.03 N·m | 89 in·lb | p. 453 |
| Clamping screw | 5.5 ± 0.45 N·m | 49 in·lb | p. 455 |
| Drive belt guard support | 7.5 ± 1 N·m | p. 460 | |
| Roller axle screw | 5 ± 0.5 N·m | p. 473 | |
| Drive pulley bolt | 120 N·m | p. 475 | |
| Drive pulley bolt First | 120.7 N·m | 89 ft·lb | p. 475 |
| Damper screws | 31.2 ± 4.07 N·m | 23 ft·lb | p. 475 |
| Bearing flange nut | 15.5 ± 1.47 N·m | 137 in·lb | p. 484 |
| Brake synthetic | 10 ± 2 N·m | p. 487 | |
| Caliper screws | 24.5 ± 3.5 N·m | p. 493 | |
| Washers | 35 ± 1 N·m | p. 493 | |
| Brake lever pivot nut | 6 ± 1.02 N·m | 53 in·lb | p. 494 |
| Master cylinder clamp | 9 ± 1 N·m | p. 494 | |
| Washers | 27 ± 1 N·m | p. 494 | |
| Middle clamp nut | 2.3 ± 0.23 N·m | 20 in·lb | p. 496 |
| Middle clamp nut | 35 ± 1 N·m | p. 496 | |
| Caliper Banjo fitting | 35.3 ± 1.36 N·m | 26 ft·lb | p. 496 |
| Master cylinder Banjo | 27 ± 1 N·m | p. 496 | |
| Caliper Banjo fitting | 27.1 ± 1.36 N·m | 20 ft·lb | p. 496 |
| Magnetic check plug | 6 ± 1 N·m | p. 501 | |
| Drain plug | 6 ± 1.02 N·m | 53 in·lb | p. 502 |
| Bearing | 24.5 ± 3.5 N·m | p. 508 |
Capacities
Values extracted from the document text. Check against the original before service work.
| Item | Value | Also | PDF page |
|---|---|---|---|
| Fuel tank | 36 L | p. 646 |
Spark plugs
Values extracted from the document text. Check against the original before service work.
| Item | Value | Also | PDF page |
|---|---|---|---|
| Spark plug | 0.6 mm | p. 626 |
Service intervals
Values extracted from the document text. Check against the original before service work.
| Item | Value | Also | PDF page |
|---|---|---|---|
| Drive chain service | 500 km | p. 14 | |
| Coolant change | 5 years | p. 15 |
Get the document
The full file is delivered by the bot. Free owner guides for Ski-Doo are also available from the manufacturer.
Open in Telegram — the bot finds this document by its catalog id and sends the file.
Open in bot- Official free Ski-Doo owner's manualsParts catalogueAll manuals