Suzuki King Quad 2008 Service manual
Suzuki King Quad · 2008 · service manual · 711 pages
Technical data
Numbers below were extracted automatically from the document. Verify them against the original manual before you order parts or apply torque.
Tightening torque
Values extracted from the document text. Check against the original before service work.
| Item | Value | Also | PDF page |
|---|---|---|---|
| Muffler mounting bolt | 22.6 N·m | 2.3 kgf·m | p. 33 |
| Muffler connecting bolt | 22.6 N·m | 2.3 kgf·m | p. 33 |
| Tie-rod lock-nut | 44.1 N·m | 4.5 kgf·m | p. 51 |
| TP sensor mounting screw | 2 N·m | 0.2 kgf·m | p. 146 |
| Mode select switch | 2 N·m | 1.5 ft·lb | p. 147 |
| Mounting screws | 2 N·m | 0.2 kgf·m · 1.5 ft·lb | p. 150 |
| P camshaft sprocket side | 10 N·m | 1 kgf·m · 7 ft·lb | p. 177 |
| Fuel tank pressure control valve | 34.6 N·m | 25.5 ft·lb | p. 255 |
| Generator cover | 11 N·m | 1.1 kgf·m · 8 ft·lb | p. 298 |
| Generator cover | 6 N·m | 0.6 kgf·m · 4.5 ft·lb | p. 298 |
| Lead wire clamp bolt | 5.9 N·m | 0.6 kgf·m | p. 298 |
| Cover bolts | 160 N·m | 16 kgf·m · 115.5 ft·lb | p. 299 |
| Cotter pin | 54.2 N·m | 40 ft·lb | p. 314 |
| Cotter pin | 59 N·m | 43.5 ft·lb | p. 314 |
| Outer dust seal | 54.2 N·m | 40 ft·lb | p. 315 |
| Conical side of washer faces outside | 28.5 N·m | 21 ft·lb | p. 315 |
| Commercially available bearing joint remover | 29 N·m | 2.9 kgf·m · 21 ft·lb | p. 318 |
| Conical side of washer faces outside | 118.6 N·m | 87.5 ft·lb | p. 332 |
| Conical side of washer faces outside | 33.2 N·m | 24.5 ft·lb | p. 332 |
| Conical side of washer faces outside | 59 N·m | 43.5 ft·lb | p. 332 |
| Mounting bolts and nuts | 60 N·m | 6 kgf·m · 43.5 ft·lb | p. 332 |
| Rear wheel hub nut | 118.7 N·m | 12.1 kgf·m | p. 335 |
| Increase shim thickness | 98.3 N·m | 72.5 ft·lb | p. 391 |
| Decrease shim thickness | 98.3 N·m | 72.5 ft·lb | p. 391 |
| Utput shaft drive bevel gear nut | 98.3 N·m | 72.5 ft·lb | p. 421 |
| Oil seal | 98.3 N·m | 72.5 ft·lb | p. 431 |
| Front brake air bleeder valve | 5.9 N·m | 0.6 kgf·m | p. 447 |
| Clear hose | 6.1 N·m | 4.5 ft·lb | p. 448 |
| Master cylinder holder bolt | 10 N·m | 1 kgf·m · 7 ft·lb | p. 451 |
| O-ring | 10.8 N·m | 8 ft·lb | p. 454 |
| Caliper piston damage | 23 N·m | 2.3 kgf·m · 16.5 ft·lb | p. 461 |
| Rear brake case mounting bolt | 10.8 N·m | 8 ft·lb | p. 467 |
| Rear brake case mounting bolt | 25.8 N·m | 19 ft·lb | p. 467 |
| Clutch shoe nut | 107.8 N·m | 79.5 ft·lb | p. 487 |
| Clutch shoe nut | 147.1 N·m | 108.5 ft·lb | p. 487 |
| Conical side of washer faces outside | 158.6 N·m | 117 ft·lb | p. 517 |
| Conical side of washer faces outside | 44.1 N·m | 32.5 ft·lb | p. 517 |
| Handlebar holder nut | 58.8 N·m | 6 kgf·m | p. 524 |
| Union bolt | 22.4 N·m | 16.5 ft·lb | p. 626 |
| Union bolt | 15.6 N·m | 11.5 ft·lb | p. 626 |
| Steering shaft upper nut | 27.1 N·m | 20 ft·lb | p. 698 |
Capacities
Values extracted from the document text. Check against the original before service work.
| Item | Value | Also | PDF page |
|---|---|---|---|
| Fuel tank | 17.5 L | p. 63 |
Spark plugs
Values extracted from the document text. Check against the original before service work.
| Item | Value | Also | PDF page |
|---|---|---|---|
| AT25 | — | p. 24 | |
| CR6E | — | p. 38 | |
| ZK9 | — | p. 584 |
Service intervals
Values extracted from the document text. Check against the original before service work.
| Item | Value | Also | PDF page |
|---|---|---|---|
| Engine oil change | 4 years | p. 30 | |
| Valve clearance check | 100 miles | p. 33 | |
| Spark plug service | 200 miles | p. 38 | |
| Coolant change | 100 miles | p. 44 |
Get the document
The full file is delivered by the bot. Free owner guides for Suzuki are also available from the manufacturer.
Open in Telegram — the bot finds this document by its catalog id and sends the file.
Open in bot- Parts catalogueAll manuals