Ski-Doo Renegade 2019 Service manual
Ski-Doo Renegade · 2019 · service manual · 1636 pages
Technical data
Numbers below were extracted automatically from the document. Verify them against the original manual before you order parts or apply torque.
Tightening torque
Values extracted from the document text. Check against the original before service work.
| Item | Value | Also | PDF page |
|---|---|---|---|
| Drain plug | 10 N·m | 89 in·lb | p. 31 |
| Filter cover screw | 3 N·m | 27 in·lb | p. 36 |
| Brake caliper bleeder | 9 N·m | 80 in·lb | p. 39 |
| Pivot screw brake lever | 6 N·m | 53 in·lb | p. 40 |
| Gearbox drain plug | 8 N·m | 71 in·lb | p. 40 |
| Oil level check plug | 10 N·m | 89 in·lb | p. 41 |
| Engine rubber mount | 24.5 ± 3.5 N·m | p. 55 | |
| Engine support screws | 42 ± 4.07 N·m | 31 ft·lb | p. 56 |
| Front Engine Support Replacement | 42 ± 4 N·m | p. 57 | |
| ENGINE RUBBER MOUNTS Engine rubber mount | 10 ± 2 N·m | p. 58 | |
| Engine support screws | 31.2 ± 4.07 N·m | 23 ft·lb | p. 64 |
| Throttle body screws | 9 ± 1 N·m | p. 74 | |
| Intake manifold screws | 9 ± 1 N·m | p. 74 | |
| Exhaust manifold nuts | 15 N·m | 133 in·lb | p. 86 |
| Muffler retaining screw | 7 ± 1.02 N·m | 62 in·lb | p. 90 |
| Throttle body screws | 0.9 ± 0.1 N·m | p. 96 | |
| Clamp | 0.9 ± 0.11 N·m | 8 in·lb | p. 96 |
| Regulator plug | 17 ± 2 N·m | p. 109 | |
| Washers | 15 ± 2 N·m | p. 117 | |
| Oil filter cover PRESSURE GAUGE | 9 ± 1.02 N·m | 80 in·lb | p. 124 |
| Oil filler tube screw | 9 ± 1.02 N·m | 80 in·lb | p. 128 |
| Drain plug | 15 ± 2.03 N·m | 133 in·lb | p. 139 |
| Drain plugs regulations | 15 ± 2.03 N·m | 133 in·lb | p. 145 |
| Oil filter cover screws | 9 ± 1.02 N·m | 80 in·lb | p. 146 |
| Oil filler tube screw | 7 ± 0.79 N·m | 62 in·lb | p. 150 |
| Cylinder | 11 ± 1.02 N·m | 97 in·lb | p. 160 |
| From throttle | 1.2 ± 0.2 N·m | p. 163 | |
| Press retaining screws | 9 ± 1.02 N·m | 80 in·lb | p. 186 |
| Water pump drive gear | 9 ± 1 N·m | p. 187 | |
| Turbo engine | 2.5 ± 0.5 N·m | p. 190 | |
| Drain screws | 9 ± 1 N·m | p. 192 | |
| Housing screws | 29.8 ± 1.36 N·m | 22 ft·lb | p. 216 |
| Starter cable nut | 7 ± 1.02 N·m | 62 in·lb | p. 219 |
| Magneto cover screws REQUIRED TOOL | 9 ± 1.02 N·m | 80 in·lb | p. 223 |
| Sprag clutch housing | 30 ± 2 N·m | p. 228 | |
| Starter retaining screws | 9 ± 1 N·m | p. 231 | |
| Screw plug timing chain | 17 ± 2 N·m | p. 246 | |
| Oil sump cover | 50 ± 3 N·m | p. 247 | |
| Valve cover | 9 ± 1.02 N·m | 80 in·lb | p. 281 |
| Camshaft | 5 ± 0.5 N·m | p. 284 | |
| Holder screws | 5 ± 0.45 N·m | 44 in·lb | p. 284 |
| Cylinder head | 9 ± 1 N·m | p. 290 | |
| Cylinder head | 20.3 ± 1.36 N·m | 15 ft·lb | p. 290 |
| Exhaust camshaft timing gear | 9 ± 1.02 N·m | 80 in·lb | p. 306 |
| PTO cover screws | 23 ± 2.71 N·m | 17 ft·lb | p. 345 |
| Cylinder block | 20 ± 2 N·m | p. 350 | |
| M9 screws | 20.3 ± 1.36 N·m | 15 ft·lb | p. 350 |
| Cylinder block | 23 ± 2 N·m | p. 350 | |
| Cylinder block | 9 ± 1 N·m | p. 351 | |
| Rod screws | 12 ± 2.03 N·m | 106 in·lb | p. 361 |
| Timing chain tensioner | 23 ± 3 N·m | p. 369 | |
| Banjo bolts | 8 N·m | 71 in·lb | p. 397 |
| Banjo bolts | 15.75 ± 0.75 N·m | p. 397 | |
| Clamp | 2.2 ± 0.2 N·m | p. 398 | |
| Clamp | 2.1 ± 0.23 N·m | 19 in·lb | p. 398 |
| ECM screw | 2.5 ± 0.45 N·m | 22 in·lb | p. 480 |
| Fuel rail retaining screw | 9 ± 1.02 N·m | 80 in·lb | p. 487 |
| O-ring | 9 ± 1 N·m | p. 494 | |
| CPS retaining screw | 9 ± 1.02 N·m | 80 in·lb | p. 494 |
| MAPTS retaining screw | 4.5 ± 0.45 N·m | 40 in·lb | p. 499 |
| BPS retaining screw | 4.5 ± 0.5 N·m | p. 501 | |
| Turn ignition key | 4.5 ± 0.45 N·m | 40 in·lb | p. 501 |
| Knock sensor screw | 24 ± 3 N·m | p. 503 | |
| Oxygen sensor | 55.6 ± 5.42 N·m | 41 ft·lb | p. 506 |
| Engine Ground | 31.2 ± 4.07 N·m | 23 ft·lb | p. 547 |
| Engine Cut-Off Switch Continuity Test | 9 ± 1 N·m | p. 575 | |
| Ignition coil retaining | 9 ± 1 N·m | p. 584 | |
| Spark plug | 13 ± 1.02 N·m | 115 in·lb | p. 584 |
| Battery holder screw | 7 ± 1.02 N·m | 62 in·lb | p. 589 |
| Battery terminals | 10 ± 2 N·m | p. 594 | |
| Battery hold down | 5 ± 0.5 N·m | p. 594 | |
| Bracket | 5 ± 0.45 N·m | 44 in·lb | p. 594 |
| Battery cover retaining | 7 ± 1 N·m | p. 594 | |
| Solenoid cable retaining (P/N 293 550 004) | 4 ± 0.5 N·m | p. 604 | |
| Taillight retaining screw | 0.8 ± 0.23 N·m | 7 in·lb | p. 611 |
| Gauge retaining screws | 1 ± 0.23 N·m | 9 in·lb | p. 623 |
Capacities
Values extracted from the document text. Check against the original before service work.
| Item | Value | Also | PDF page |
|---|---|---|---|
| Fuel tank | 45 L | p. 966 | |
| Fuel tank | 40 L | p. 967 | |
| Fuel tank | 36 L | p. 970 |
Spark plugs
Values extracted from the document text. Check against the original before service work.
| Item | Value | Also | PDF page |
|---|---|---|---|
| MR7BI-8 | — | p. 37 | |
| M14 | — | p. 322 | |
| Spark plug | 0.4 mm | p. 741 | |
| MR8BI-8 | — | p. 966 | |
| MR7BI | — | p. 1306 |
Service intervals
Values extracted from the document text. Check against the original before service work.
| Item | Value | Also | PDF page |
|---|---|---|---|
| Coolant change | 5 years | p. 26 | |
| Engine oil change | 2 years | p. 28 | |
| Spark plug service | 5 years | p. 1276 | |
| Drive chain service | 3 years | p. 1537 |
Get the document
The full file is delivered by the bot. Free owner guides for Ski-Doo are also available from the manufacturer.
Open in Telegram — the bot finds this document by its catalog id and sends the file.
Open in bot- Official free Ski-Doo owner's manualsParts catalogueAll manuals