Ski-Doo Skandic 2015 Service manual
Ski-Doo Skandic · 2015 · service manual · 1561 pages
Technical data
Numbers below were extracted automatically from the document. Verify them against the original manual before you order parts or apply torque.
Tightening torque
Values extracted from the document text. Check against the original before service work.
| Item | Value | Also | PDF page |
|---|---|---|---|
| Water pump | 9 ± 1 N·m | p. 29 | |
| Drain plug I | 10 N·m | 89 in·lb | p. 30 |
| Oil Filter Cover | 9 ± 1 N·m | p. 34 | |
| Filter cover screw I | 3 N·m | 27 in·lb | p. 35 |
| Brake caliper bleeder I | 9 N·m | 80 in·lb | p. 38 |
| Bra ke caliper | 9 N·m | 80 in·lb | p. 38 |
| Pivot screw brake lever I | 6 N·m | 53 in·lb | p. 39 |
| Oil level check plug I | 10 N·m | 89 in·lb | p. 40 |
| Engine mounting | 24.5 ± 3.5 N·m | p. 55 | |
| Engine support screws I | 42 ± 4 N·m | p. 56 | |
| Rubber mount screws (MAG Side) | 24.4 ± 4.07 N·m | 18 ft·lb | p. 56 |
| Eng ine support screws I | 42 ± 4 N·m | 31 ft·lb | p. 57 |
| Rubber mount screws I | 10 ± 2 N·m | p. 58 | |
| Section 02 ENGINE | 9 ± 1 N·m | 80 in·lb | p. 68 |
| Lighten regulator plug | 17 ± 2 N·m | p. 79 | |
| Magneto cover | 9 ± 1 N·m | p. 98 | |
| Semble radiator w hen rem oved for access | 9 ± 1 N·m | p. 99 | |
| Rubber mount screw (MAG Side) | 24.4 ± 4.07 N·m | 18 ft·lb | p. 176 |
| Front and Rear Engine Rubber Mount | 24.5 ± 3.5 N·m | p. 177 | |
| Throttle body screws | 9 ± 1 N·m | p. 188 | |
| Circuit MAPTS RETAINING SCREW | 4.5 ± 0.5 N·m | p. 401 | |
| Engine Cut-Off Switch Continuity Test | 9 ± 1 N·m | p. 426 | |
| Off switch connector | 9 ± 1 N·m | p. 426 | |
| Pivot screws I | 20 N·m | 15 ft·lb | p. 470 |
| Cam screws I | 32 N·m | 24 ft·lb | p. 470 |
| Countershaft bearing area | 25 N·m | 18 ft·lb | p. 472 |
| Haft bearing area | 25 N·m | 18 ft·lb | p. 472 |
| Front of bearing support | 25 N·m | 18 ft·lb | p. 474 |
| Fra me member screw | 14 N·m | 124 in·lb | p. 474 |
| Suspension | 48 N·m | p. 477 | |
| Ski runner nuts | 8 N·m | 71 in·lb | p. 482 |
| Handlebar clamp screws | 25 N·m | 18 ft·lb | p. 484 |
| Expedition Models MOUNTING BOLT | 14 N·m | 124 in·lb | p. 491 |
| Tig hten emergency stop support retaining screws | 2 ± 0.2 N·m | p. 492 | |
| ITC housing retain | 9 ± 0.1 N·m | p. 492 | |
| Gearbox Oil CHECK PLUG | 10 ± 1 N·m | 89 in·lb | p. 798 |
| Lock nuts | 48 ± 6 N·m | p. 805 | |
| Oil filter | 10 ± 1 N·m | 89 in·lb | p. 913 |
| Coolant hose clamp I | 5.5 N·m | 49 in·lb | p. 916 |
| Gearbox drain plug I | 8 N·m | p. 926 | |
| Engine rubber mount | 5 ± 5 N·m | p. 944 | |
| Engine rubbe r mount | 5 ± 3.5 N·m | p. 945 | |
| Engine support screws I | 4 ± 3 N·m | p. 947 | |
| ENGINE RUBBER MOUNTS Engine rubber mount | 182 N·m | p. 947 | |
| Intake manifold screws I | 11 ± 1 N·m | p. 954 | |
| Exhaust fla nge screws | 1.4 N·m | 1 ft·lb | p. 957 |
| Exhaust flange screws I | 24 ± 2 N·m | p. 958 | |
| Exhaust pipes | 24.4 ± 1.36 N·m | 18 ft·lb | p. 958 |
| Oil pressure regulator plug | 29.8 ± 4.07 N·m | 22 ft·lb | p. 968 |
| Washers | 20 ± 2 N·m | p. 976 | |
| Oil drain plugs | 20 ± 1 N·m | p. 976 | |
| Coolant hose clamps I | 5.5 ± 0.5 N·m | p. 987 | |
| Retaining screws | 11 ± 1 N·m | p. 988 | |
| Magn eto cove r screws I | 11 ± 1 N·m | p. 995 | |
| Rotor retaining screw I | 150 ± 10 N·m | p. 998 | |
| Sprag clutch housing | 30 ± 2 N·m | p. 1000 | |
| Starter reta ining screws | 11 N·m | 97 in·lb | p. 1002 |
| Starter cable nut | 7 N·m | 62 in·lb | p. 1002 |
| Valve cover screws | 10.1 ± 1.02 N·m | 89 in·lb | p. 1025 |
| Fuel pump mounting nuts | 5 N·m | p. 1110 | |
| Carburetor mounting cl amps | 0.6 N·m | p. 1110 | |
| Throttle Body Synchronization | 1 ± 0.2 N·m | p. 1191 | |
| TPS retain ing screws I | 2 ± 0.4 N·m | p. 1195 | |
| Knock sensor screw | 29 N·m | p. 1205 | |
| ECM reta ining nuts I | 3.5 N·m | 31 in·lb | p. 1269 |
| Ignition co il retain ing screws I | 10 N·m | 89 in·lb | p. 1286 |
| Valve cover | 11 N·m | p. 1290 | |
| Primary Winding SPARK PLUGS | 11 N·m | 97 in·lb | p. 1290 |
| Voltage re.gulator/rectifier | 5 N·m | p. 1295 | |
| Battery retaining screws | 10 N·m | 89 in·lb | p. 1311 |
| Battery terminal screws | 3 N·m | 27 in·lb | p. 1311 |
| Voltage regulator screws | 5 N·m | p. 1318 | |
| Starter mounting screws | 28 N·m | 21 ft·lb | p. 1330 |
| Solenoid power cable terminals I | 4 N·m | 35 in·lb | p. 1332 |
| Hex screw | 28 N·m | 21 ft·lb | p. 1339 |
| Clamping screw I | 5.5 ± 0.5 N·m | p. 1383 | |
| Pivot nut I | 5 N·m | 44 in·lb | p. 1393 |
| Ring gear screw I | 27 N·m | 20 ft·lb | p. 1406 |
| Spring cover sc rews I | 25 N·m | 18 ft·lb | p. 1407 |
| Lever screws I | 10 N·m | 89 in·lb | p. 1408 |
| Washer | 10 N·m | 89 in·lb | p. 1409 |
| Washer | 120 N·m | 89 ft·lb | p. 1409 |
| Calibration screw nuts I | 10 N·m | 89 in·lb | p. 1410 |
| Pivot screws I | 6.8 N·m | 5 ft·lb | p. 1420 |
| Cam screws | 32 N·m | 24 ft·lb | p. 1420 |
| Countershaft bearing | 24.4 N·m | 18 ft·lb | p. 1422 |
| Front rubber mount bolt I | 25 N·m | 18 ft·lb | p. 1424 |
| Frame member bolt | 14 N·m | 124 in·lb | p. 1424 |
| Top of bearing support | 10.1 N·m | 89 in·lb | p. 1438 |
| Brake pad pin I | 10 N·m | 89 in·lb | p. 1442 |
| Caliper retaining screw I | 25 N·m | 18 ft·lb | p. 1446 |
| Washers | 35 N·m | 26 ft·lb | p. 1446 |
| Brake lever nut I | 6 N·m | 53 in·lb | p. 1448 |
| Speed sensor | 8 N·m | 71 in·lb | p. 1450 |
Capacities
Values extracted from the document text. Check against the original before service work.
| Item | Value | Also | PDF page |
|---|---|---|---|
| Fuel tank | 45 L | p. 502 | |
| Engine oil | 3.7 L | p. 822 | |
| Engine oil | 2.8 L | p. 823 | |
| Fuel tank | 40 L | p. 1530 |
Spark plugs
Values extracted from the document text. Check against the original before service work.
| Item | Value | Also | PDF page |
|---|---|---|---|
| M14 | — | p. 153 | |
| BR9ECS | — | p. 827 | |
| CR7EB | — | p. 829 | |
| TP88 | — | p. 1299 |
Service intervals
Values extracted from the document text. Check against the original before service work.
| Item | Value | Also | PDF page |
|---|---|---|---|
| Coolant change | 5 years | p. 26 |
Get the document
The full file is delivered by the bot. Free owner guides for Ski-Doo are also available from the manufacturer.
Open in Telegram — the bot finds this document by its catalog id and sends the file.
Open in bot- Official free Ski-Doo owner's manualsParts catalogueAll manuals