BRP Outlander 2013 Shop manual
BRP Outlander · 2013 · shop manual · 842 pages
Technical data
Numbers below were extracted automatically from the document. Verify them against the original manual before you order parts or apply torque.
Tightening torque
Values extracted from the document text. Check against the original before service work.
| Item | Value | Also | PDF page |
|---|---|---|---|
| Wheel nut | 100 ± 10 N·m | 74 ft·lb | p. 27 |
| CVT Air Filter Cleaning CVT air filter screws | 2.5 ± 0.45 N·m | 22 in·lb | p. 74 |
| Engine retaining bolts | 62.4 ± 8.13 N·m | 46 ft·lb | p. 98 |
| Suspension | 6 N·m | p. 104 | |
| Head pipe nuts | 13 ± 1 N·m | p. 111 | |
| Rear cylinder | 13 ± 1.02 N·m | 115 in·lb | p. 111 |
| Housing | 10.1 ± 1.02 N·m | 89 in·lb | p. 134 |
| Regulator/rectifier | 10 ± 1 N·m | p. 170 | |
| Ified one cylinder at a time | 20 ± 2 N·m | p. 178 | |
| RH side panel | 7 ± 0.8 N·m | p. 185 | |
| Lever | 10 ± 1 N·m | p. 210 | |
| Camshaft | 10.1 ± 1.02 N·m | 89 in·lb | p. 210 |
| Vere engine damage | 20 ± 2 N·m | p. 237 | |
| Shaft CVT side | 25 ± 3 N·m | p. 340 | |
| Shaft CVT side | 24.4 ± 2.71 N·m | 18 ft·lb | p. 340 |
| Shift plate nut | 9 ± 1 N·m | 80 in·lb | p. 346 |
| TPS retaining screws | 3 N·m | p. 468 | |
| Fuel tank retaining | 6.5 ± 0.5 N·m | p. 486 | |
| Fuel Pump Prefilter Replacement | 29 ± 1 N·m | p. 490 | |
| Fuel pump retaining nut | 28.5 ± 1.36 N·m | 21 ft·lb | p. 490 |
| Ignition Coil Connector Access fied | 8 ± 1 N·m | 71 in·lb | p. 529 |
| Battery retaining plate | 5 N·m | p. 535 | |
| Solenoid mounting | 4.5 ± 0.45 N·m | 40 in·lb | p. 541 |
| Front skid plate | 16 ± 2.03 N·m | 142 in·lb | p. 568 |
| Retaining screws | 7 ± 5 N·m | p. 568 | |
| Pinion nut | 180 ± 15 N·m | p. 578 | |
| Front propeller shaft | 75 ± 5 N·m | p. 578 | |
| Adapter retaining screw | 74.6 ± 5.42 N·m | 55 ft·lb | p. 578 |
| M8 nut securing front | 24.5 ± 3.5 N·m | p. 578 | |
| Differential housing | 33 ± 3 N·m | p. 578 | |
| Hi-temp bearing grease | 75 ± 5 N·m | p. 581 | |
| Propeller shaft screw | 75 ± 5 N·m | p. 587 | |
| PRELOAD Pinion Gear | 0.6 N·m | 5 in·lb | p. 590 |
| Preload side Final drive housing | 32.5 ± 3.5 N·m | p. 591 | |
| Lubricate oil seal | 180.3 ± 14.91 N·m | 133 ft·lb | p. 592 |
| Final drive retaining nuts | 89.5 ± 5.42 N·m | 66 ft·lb | p. 592 |
| Inner ring | 3 ± 1 N·m | 27 in·lb | p. 594 |
| Inner ring | 8 ± 1 N·m | 71 in·lb | p. 594 |
| Locking nut | 33.9 ± 1.36 N·m | 25 ft·lb | p. 605 |
| Brake lever mounting | 9 ± 1 N·m | p. 609 | |
| Tie-rod lock nut | 34 ± 2 N·m | p. 613 | |
| Tie-rod lock nut | 72 ± 7 N·m | p. 613 | |
| Tie rod end retaining nut | 71.9 ± 6.78 N·m | 53 ft·lb | p. 613 |
| Retaining nuts, DPS | 24.5 ± 3.5 N·m | p. 644 | |
| Heat shield retaining nuts | 24.4 ± 4.07 N·m | 18 ft·lb | p. 644 |
| DPS bracket retaining | 24.4 ± 4.07 N·m | 18 ft·lb | p. 646 |
| Positioning screw | 50 N·m | 37 ft·lb | p. 651 |
| Pitman arm retaining nut | 71.9 ± 8.13 N·m | 53 ft·lb | p. 652 |
| Suspension | 3 ± 0.5 N·m | p. 653 | |
| Upper shock absorber | 61 ± 9 N·m | p. 655 | |
| Lower shock absorber | 73 ± 7 N·m | p. 655 | |
| Nut securing ball joint | 48 ± 6 N·m | p. 656 | |
| Ball joint nut | 44.7 ± 5.42 N·m | 33 ft·lb | p. 658 |
| Suspension | 3.1 ± 0.45 N·m | 27 in·lb | p. 661 |
| Suspension | 61 ± 9 N·m | p. 661 | |
| Suspension | 225 ± 10 N·m | p. 661 | |
| Shock absorber nuts | 61 ± 9.49 N·m | 45 ft·lb | p. 663 |
| Bolts securing anti-sway | 24.5 ± 3.5 N·m | p. 666 | |
| Bolts securing anti-sway | 61 ± 9 N·m | p. 666 | |
| Pivot nuts | 255 ± 10 N·m | p. 669 | |
| LH side nut | 254.9 ± 9.49 N·m | 188 ft·lb | p. 669 |
| Bolts securing trailing | 61 ± 9 N·m | p. 669 | |
| Trailing arm fasteners | 61 ± 9 N·m | p. 669 | |
| Protective plate retaining | 4.5 ± 0.5 N·m | p. 669 | |
| ACS solenoid | 53 N·m | p. 671 | |
| Release valve | 52.9 N·m | 39 ft·lb | p. 671 |
| Upper and lower shock absorber bolts | 53 N·m | 39 ft·lb | p. 692 |
| Air hose fitting | 19 N·m | 168 in·lb | p. 692 |
| ACS solenoid | 19 N·m | p. 694 | |
| Release valve | 19 N·m | 168 in·lb | p. 694 |
| Pipe sealant (pipe sealant) | 6 N·m | 53 in·lb | p. 694 |
| Brake caliper | 8.5 ± 1.5 N·m | p. 725 | |
| Brake light switch | 28.5 ± 1.36 N·m | 21 ft·lb | p. 729 |
| Brake pedal bolt | 10 ± 2 N·m | p. 730 | |
| Master cylinder | 10.1 ± 2.03 N·m | 89 in·lb | p. 730 |
| Master cylinder | 27.5 ± 2.5 N·m | p. 730 | |
| Brake hoses and bleeder | 28.5 ± 1.5 N·m | p. 730 |
Capacities
Values extracted from the document text. Check against the original before service work.
| Item | Value | Also | PDF page |
|---|---|---|---|
| Fuel tank | 20.5 L | p. 12 | |
| Engine oil | 2 L | p. 67 |
Spark plugs
Values extracted from the document text. Check against the original before service work.
| Item | Value | Also | PDF page |
|---|---|---|---|
| Spark plug | 0.6 mm | p. 9 | |
| M10 | — | p. 190 |
Get the document
The full file is delivered by the bot. Free owner guides for BRP are also available from the manufacturer.
Open in Telegram — the bot finds this document by its catalog id and sends the file.
Open in bot- Official free BRP owner's manualsParts catalogueAll manuals