Ski-Doo Chassis Gen5 Deep Manual
Ski-Doo Chassis Gen5 Deep · manual · 85 pages
Technical data
Numbers below were extracted automatically from the document. Verify them against the original manual before you order parts or apply torque.
Tightening torque
Values extracted from the document text. Check against the original before service work.
| Item | Value | Also | PDF page |
|---|---|---|---|
| Front shock absorber | 31.5 ± 3.5 N·m | p. 10 | |
| Retaining nuts | 31.2 ± 4.07 N·m | 23 ft·lb | p. 10 |
| Upper arm ball joint | 48 ± 6 N·m | p. 11 | |
| Lower arm ball joint | 48 ± 6 N·m | p. 13 | |
| Ski leg retaining nut | 47.5 ± 5.42 N·m | 35 ft·lb | p. 14 |
| Rear Suspension | 0.75 ± 0.25 N·m | p. 18 | |
| Rear Suspension | 36 ± 2 N·m | p. 18 | |
| Suspension | 3 ± 0.2 N·m | p. 20 | |
| Suspension | 3.1 ± 0.23 N·m | 27 in·lb | p. 20 |
| Front arm bolts | 47.5 ± 5.42 N·m | 35 ft·lb | p. 23 |
| Rear arm bolts | 14.9 ± 2.71 N·m | 11 ft·lb | p. 23 |
| Idler wheel nut | 18 ± 2.03 N·m | 159 in·lb | p. 23 |
| Hook retaining nut | 9 ± 3.05 N·m | 80 in·lb | p. 24 |
| Center shock absorber | 48 ± 6 N·m | p. 29 | |
| Center shock absorber | 31.5 ± 3.5 N·m | p. 29 | |
| Shock absorber | 24.5 ± 3.5 N·m | p. 29 | |
| Retaining bolts | 24.4 ± 4.07 N·m | 18 ft·lb | p. 29 |
| Front arm lower nut | 70.5 ± 10.17 N·m | 52 ft·lb | p. 33 |
| Link rods upper nut | 36.6 ± 1.36 N·m | 27 ft·lb | p. 34 |
| Nut Rear shock absorber | 31.5 ± 3.5 N·m | p. 34 | |
| M8 elastic flanged nut | 32 ± 4 N·m | p. 35 | |
| M8 elastic flanged nut | 24.5 ± 3.5 N·m | p. 35 | |
| Jam nut | 18.5 ± 3.5 N·m | 164 in·lb | p. 41 |
| Ski runner nut | 8 ± 1.02 N·m | 71 in·lb | p. 42 |
| Outside of Ski nut | 47.5 ± 5.42 N·m | 35 ft·lb | p. 43 |
| Throttle lever retaining | 1.5 ± 0.2 N·m | p. 47 | |
| Throttle lever pivot | 1.5 ± 0.2 N·m | p. 48 | |
| Clamp screws | 24.4 ± 4.07 N·m | 18 ft·lb | p. 49 |
| Steering column and ski leg | 24.5 ± 3.5 N·m | p. 50 | |
| Outer tie-rod end nut | 47.5 ± 5.42 N·m | 35 ft·lb | p. 52 |
| Inner tie-rod end nut | 24.4 ± 4.07 N·m | 18 ft·lb | p. 52 |
| Upper steering column | 12.5 ± 2.5 N·m | p. 53 | |
| Support nut | 12.5 ± 2.49 N·m | 111 in·lb | p. 53 |
| Lower steering column | 23.5 ± 3.5 N·m | p. 53 | |
| Support nut | 23 ± 4.07 N·m | 17 ft·lb | p. 53 |
| Housing screw | 2.3 ± 0.23 N·m | 20 in·lb | p. 57 |
| Gauge support screw | 1.8 ± 0.23 N·m | 16 in·lb | p. 59 |
| Gauge support screw | 1.3 ± 0.2 N·m | p. 59 | |
| Display bracket screw | 1.4 ± 0.23 N·m | 12 in·lb | p. 59 |
| Intake duct clamp | 1 ± 0.23 N·m | 9 in·lb | p. 60 |
| Retaining screws | 1.8 ± 0.2 N·m | p. 60 | |
| Console nut | 6 ± 1.02 N·m | 53 in·lb | p. 62 |
| Front bumper nut | 5 ± 0.45 N·m | 44 in·lb | p. 63 |
| Tom pan cap | 2 ± 0.5 N·m | p. 64 | |
| Side bottom pan screw | 2.8 ± 0.2 N·m | p. 66 | |
| Pinched nut | 2.8 ± 0.23 N·m | 25 in·lb | p. 66 |
| Side bottom pan screw | 2 ± 0.5 N·m | p. 66 | |
| Panel nut | 2 ± 0.45 N·m | 18 in·lb | p. 66 |
| Rear bumper screws | 16 ± 2.03 N·m | 142 in·lb | p. 67 |
| Engine support screw | 27 ± 1 N·m | p. 85 | |
| Head screw | 0.5 ± 0.11 N·m | 4 in·lb | p. 85 |
| Oil tank clamp Torx | 1.25 ± 0.25 N·m | p. 85 |
Get the document
The full file is delivered by the bot. Free owner guides for Ski-Doo are also available from the manufacturer.
Open in Telegram — the bot finds this document by its catalog id and sends the file.
Open in bot- Official free Ski-Doo owner's manualsParts catalogueAll manuals