Ski-Doo MY22 Backcountry Pdf 2022 Manual
Ski-Doo MY22 Backcountry Pdf · 2022 · manual · 405 pages
Technical data
Numbers below were extracted automatically from the document. Verify them against the original manual before you order parts or apply torque.
Tightening torque
Values extracted from the document text. Check against the original before service work.
| Item | Value | Also | PDF page |
|---|---|---|---|
| Spark plug | 28.5 ± 1.36 N·m | 21 ft·lb | p. 30 |
| INTAKE SYSTEM subsection | 31.2 ± 4.07 N·m | 23 ft·lb | p. 42 |
| Snug all bolts | 33 ± 3 N·m | p. 42 | |
| Muffler retaining screw | 7 ± 1.02 N·m | 62 in·lb | p. 55 |
| Exhaust Gas | 45 ± 2 N·m | p. 60 | |
| Temperature Sensor | 44.7 ± 1.36 N·m | 33 ft·lb | p. 60 |
| Cylinder | 5.5 ± 0.5 N·m | p. 63 | |
| Head | 5.5 ± 0.45 N·m | 49 in·lb | p. 63 |
| Coolant hose clamp | 3.1 ± 0.45 N·m | 27 in·lb | p. 65 |
| M6 screw on chassis | 10 ± 2 N·m | p. 122 | |
| Approved spark plug socket | 27.5 ± 2.5 N·m | p. 161 | |
| Spark plug | 23 ± 1.36 N·m | 17 ft·lb | p. 170 |
| Ignition coil retaining | 2.4 ± 0.2 N·m | p. 173 | |
| Battery terminals | 10 ± 2 N·m | p. 178 | |
| Battery hold down | 5 ± 0.5 N·m | p. 178 | |
| Bracket | 5 ± 0.45 N·m | 44 in·lb | p. 178 |
| Battery cover retaining | 7 ± 1 N·m | p. 178 | |
| Solenoid cable retaining | 4 ± 0.5 N·m | p. 189 | |
| Retaining screws | 1 ± 0.23 N·m | 9 in·lb | p. 204 |
| Torx screw | 7.5 ± 1.02 N·m | 66 in·lb | p. 217 |
| Elastic nut | 10.1 ± 2.03 N·m | 89 in·lb | p. 217 |
| Clamping screw | 5.5 ± 0.45 N·m | 49 in·lb | p. 219 |
| Roller axle screw | 5 ± 0.45 N·m | 44 in·lb | p. 230 |
| Damper screws | 31.2 ± 4.07 N·m | 23 ft·lb | p. 231 |
| Drive pulley bolt | 120 ± 5 N·m | p. 232 | |
| Drive pulley bolt First | 120.7 N·m | 89 ft·lb | p. 244 |
| Bearing flange nut | 15.5 ± 1.47 N·m | 137 in·lb | p. 253 |
| Brake lever pivot nut | 6 ± 1 N·m | p. 259 | |
| Brake lever pivot nut | 8.5 ± 1.5 N·m | p. 259 | |
| Brake caliper bleeder | 8.5 ± 1.47 N·m | 75 in·lb | p. 259 |
| Brake pad pin | 10.1 ± 2.03 N·m | 89 in·lb | p. 261 |
| Master cylinder clamp | 9 ± 1 N·m | p. 264 | |
| Washers | 27 ± 1 N·m | p. 264 | |
| Middle clamp nut | 2.3 ± 0.23 N·m | 20 in·lb | p. 266 |
| Middle clamp nut | 35 ± 1 N·m | p. 266 | |
| Caliper Banjo fitting | 35.3 ± 1.36 N·m | 26 ft·lb | p. 266 |
| Master cylinder Banjo | 27 ± 1 N·m | p. 266 | |
| Caliper Banjo fitting | 27.1 ± 1.36 N·m | 20 ft·lb | p. 266 |
| Magnetic check plug | 6 ± 1 N·m | p. 269 | |
| Drain plug | 6 ± 1.02 N·m | 53 in·lb | p. 270 |
| Bearing | 24.5 ± 3.5 N·m | p. 276 | |
| Rear idler wheel | 48 ± 6 N·m | p. 285 | |
| Retaining screws | 47.5 ± 5.42 N·m | 35 ft·lb | p. 285 |
| Rear idler wheel | 24.5 ± 3.5 N·m | p. 285 | |
| Front shock absorber | 31.5 ± 3.5 N·m | p. 296 | |
| Retaining nuts | 31.2 ± 4.07 N·m | 23 ft·lb | p. 296 |
| Suspension | 3 ± 0.2 N·m | p. 306 | |
| Front and rear arm | 48 ± 6 N·m | p. 309 | |
| Upper bolts | 47.5 ± 5.42 N·m | 35 ft·lb | p. 309 |
| Rear shock absorber | 24.5 ± 3.5 N·m | p. 312 | |
| Center shock absorber | 40 ± 5 N·m | p. 313 | |
| Throttle rods upper nut | 36.6 ± 1.36 N·m | 27 ft·lb | p. 317 |
| Throttle rods upper nut | 24.5 ± 3.5 N·m | p. 317 | |
| Jam nut | 18.5 ± 3.5 N·m | 164 in·lb | p. 326 |
| Runner nut | 8 ± 1.02 N·m | 71 in·lb | p. 327 |
| Ski nut | 47.5 ± 5.42 N·m | 35 ft·lb | p. 328 |
| Adjusting knob screw | 9 ± 1.02 N·m | 80 in·lb | p. 331 |
| Adjusting knob screw | 24.5 ± 3.5 N·m | p. 331 | |
| Indicator screw | 24.4 ± 4.07 N·m | 18 ft·lb | p. 331 |
| Extension nuts | 3 ± 0.5 N·m | p. 333 | |
| Extension nuts | 3.1 ± 0.45 N·m | 27 in·lb | p. 333 |
| Multifunction switch | 2.4 ± 0.2 N·m | p. 335 | |
| Throttle lever retaining | 1.5 ± 0.2 N·m | p. 337 | |
| Throttle lever pivot | 1.5 ± 0.2 N·m | p. 338 | |
| Clamp screws | 24.4 ± 4.07 N·m | 18 ft·lb | p. 339 |
| Outer tie-rod end nut | 48 ± 6 N·m | p. 342 | |
| Outer tie-rod end nut | 24.5 ± 3.5 N·m | p. 342 | |
| Inner tie-rod end nut | 24.4 ± 4.07 N·m | 18 ft·lb | p. 342 |
| Upper steering column | 12.5 ± 2.5 N·m | p. 344 | |
| Support nut | 12.5 ± 2.49 N·m | 111 in·lb | p. 344 |
| Lower steering column | 23.5 ± 3.5 N·m | p. 344 | |
| Support nut | 23 ± 4.07 N·m | 17 ft·lb | p. 344 |
| Housing screw | 2.3 ± 0.23 N·m | 20 in·lb | p. 350 |
| Gauge support screw | 2.3 ± 0.23 N·m | 20 in·lb | p. 352 |
| Hood hexagonal screw | 1.8 ± 0.23 N·m | 16 in·lb | p. 354 |
| Hood hexagonal screw | 2.3 ± 0.2 N·m | p. 354 | |
| Hood Torx screw | 2.3 ± 0.02 N·m | 20 in·lb | p. 354 |
| Headlight Torx screw | 2.3 ± 0.23 N·m | 20 in·lb | p. 354 |
| Console nut | 2.3 ± 0.23 N·m | 20 in·lb | p. 355 |
| Front bumper nut | 5 ± 0.45 N·m | 44 in·lb | p. 356 |
| Bottom pan screw | 1.8 ± 0.23 N·m | 16 in·lb | p. 357 |
| Side bottom pan screw | 2.8 ± 0.23 N·m | 25 in·lb | p. 358 |
| Rear bumper screws | 16 ± 2.03 N·m | 142 in·lb | p. 359 |
Service intervals
Values extracted from the document text. Check against the original before service work.
| Item | Value | Also | PDF page |
|---|---|---|---|
| Drive chain service | 500 km | p. 27 | |
| Coolant change | 5 years | p. 28 |
Get the document
The full file is delivered by the bot. Free owner guides for Ski-Doo are also available from the manufacturer.
Open in Telegram — the bot finds this document by its catalog id and sends the file.
Open in bot- Official free Ski-Doo owner's manualsParts catalogueAll manuals