Ski-Doo MY23 Renegade Pdf 2023 Manual
Ski-Doo MY23 Renegade Pdf · 2023 · manual · 805 pages
Technical data
Numbers below were extracted automatically from the document. Verify them against the original manual before you order parts or apply torque.
Tightening torque
Values extracted from the document text. Check against the original before service work.
| Item | Value | Also | PDF page |
|---|---|---|---|
| Spark plug | 28.5 ± 1.36 N·m | 21 ft·lb | p. 46 |
| INTAKE SYSTEM subsection | 31.2 ± 4.07 N·m | 23 ft·lb | p. 62 |
| Snug all bolts | 33 ± 3 N·m | p. 62 | |
| Engine rubber mount | 24.5 ± 3.5 N·m | p. 71 | |
| Engine support screws | 42 ± 4.07 N·m | 31 ft·lb | p. 72 |
| Front Engine Support Replacement | 42 ± 4 N·m | p. 73 | |
| ENGINE RUBBER MOUNTS Engine rubber mount | 10 ± 2 N·m | p. 74 | |
| Engine support screws | 31.2 ± 4.07 N·m | 23 ft·lb | p. 80 |
| Muffler retaining screw | 7 ± 1.02 N·m | 62 in·lb | p. 99 |
| Exhaust Gas | 45 ± 2 N·m | p. 104 | |
| Temperature Sensor | 44.7 ± 1.36 N·m | 33 ft·lb | p. 104 |
| Exhaust pipe retaining | 7 ± 1 N·m | p. 107 | |
| Cylinder | 5.5 ± 0.5 N·m | p. 123 | |
| Head | 5.5 ± 0.45 N·m | 49 in·lb | p. 123 |
| Coolant hose clamp | 3.1 ± 0.45 N·m | 27 in·lb | p. 125 |
| Turbo engine | 2.5 ± 0.5 N·m | p. 133 | |
| Drain screws | 9 ± 1 N·m | p. 135 | |
| M6 screw on chassis | 10 ± 2 N·m | p. 226 | |
| Approved spark plug socket | 27.5 ± 2.5 N·m | p. 283 | |
| Spark plug | 23 ± 1.36 N·m | 17 ft·lb | p. 296 |
| Ignition coil retaining | 2.4 ± 0.2 N·m | p. 299 | |
| Battery terminals | 10 ± 2 N·m | p. 304 | |
| Battery hold down | 5 ± 0.5 N·m | p. 304 | |
| Bracket | 5 ± 0.45 N·m | 44 in·lb | p. 304 |
| Battery cover retaining | 7 ± 1 N·m | p. 304 | |
| Battery hold down | 7 ± 1 N·m | p. 315 | |
| Bracket | 7 ± 1.02 N·m | 62 in·lb | p. 315 |
| Solenoid cable retaining | 4 ± 0.5 N·m | p. 321 | |
| CONNECTOR CONNECTOR retaining screws | 1 ± 0.23 N·m | 9 in·lb | p. 353 |
| Torx screw | 7.5 ± 1.02 N·m | 66 in·lb | p. 375 |
| Elastic nut | 10.1 ± 2.03 N·m | 89 in·lb | p. 375 |
| Clamping screw | 5.5 ± 0.45 N·m | 49 in·lb | p. 377 |
| Distorted spare belt | 10 ± 2 N·m | p. 381 | |
| Distorted spare belt | 24.5 ± 3.5 N·m | p. 381 | |
| Roller axle screw | 5 ± 0.45 N·m | 44 in·lb | p. 394 |
| Damper screws | 31.2 ± 4.07 N·m | 23 ft·lb | p. 395 |
| Centrifugal lever | 5 ± 0.6 N·m | p. 404 | |
| Pivot nut | 5 ± 0.56 N·m | 44 in·lb | p. 404 |
| Spring cover retaining | 10 ± 2 N·m | p. 404 | |
| Drive pulley bolt | 120 N·m | p. 418 | |
| Drive pulley bolt First | 120.7 N·m | 89 ft·lb | p. 418 |
| Bearing flange nut | 15.5 ± 1.47 N·m | 137 in·lb | p. 427 |
| Pivot screws | 17 ± 1 N·m | 150 in·lb | p. 438 |
| Brake lever pivot nut | 6 ± 1 N·m | p. 447 | |
| Brake lever pivot nut | 8.5 ± 1.5 N·m | p. 447 | |
| Brake caliper bleeder | 8.5 ± 1.47 N·m | 75 in·lb | p. 447 |
| Brake pad pin | 10.1 ± 2.03 N·m | 89 in·lb | p. 449 |
| Master cylinder clamp | 9 ± 1 N·m | p. 452 | |
| Washers | 27 ± 1 N·m | p. 452 | |
| Middle clamp nut | 2.3 ± 0.23 N·m | 20 in·lb | p. 454 |
| Middle clamp nut | 35 ± 1 N·m | p. 454 | |
| Caliper Banjo fitting | 35.3 ± 1.36 N·m | 26 ft·lb | p. 454 |
| Master cylinder Banjo | 27 ± 1 N·m | p. 454 | |
| Caliper Banjo fitting | 27.1 ± 1.36 N·m | 20 ft·lb | p. 454 |
| Magnetic check plug | 6 ± 1 N·m | p. 457 | |
| Drain plug | 6 ± 1.02 N·m | 53 in·lb | p. 458 |
| Bearing | 24.5 ± 3.5 N·m | p. 464 | |
| Actuator coupling | 7 ± 0.5 N·m | p. 476 | |
| 219100985-021-010 shaft nut | 7 ± 0.45 N·m | 62 in·lb | p. 476 |
| Upper gear screw | 48 ± 6 N·m | p. 488 | |
| Screws Same | 10 ± 2 N·m | p. 489 | |
| Reverse gear screw | 24.4 ± 4.07 N·m | 18 ft·lb | p. 489 |
| Rear idler wheel | 48 ± 6 N·m | p. 499 | |
| Retaining screws | 47.5 ± 5.42 N·m | 35 ft·lb | p. 499 |
| Rear idler wheel | 24.5 ± 3.5 N·m | p. 499 | |
| Front shock absorber | 31.5 ± 3.5 N·m | p. 533 | |
| Retaining nuts | 31.2 ± 4.07 N·m | 23 ft·lb | p. 533 |
| Front arm bolts | 47.5 ± 5.42 N·m | 35 ft·lb | p. 547 |
| Rear arm connecting | 61 N·m | p. 547 | |
| Rod screws | 61 ± 9.49 N·m | 45 ft·lb | p. 547 |
| Clamp screws | 2.5 ± 0.45 N·m | 22 in·lb | p. 548 |
| Clamp screws | 0.4 ± 0.1 N·m | p. 548 | |
| Knob screw | 0.5 ± 0.11 N·m | 4 in·lb | p. 548 |
| Support screws | 5 ± 1.02 N·m | 44 in·lb | p. 550 |
| Support screws | 2.5 ± 0.5 N·m | p. 550 | |
| Clamp screws | 1.5 ± 0.5 N·m | p. 550 | |
| Bleeding and Reassembling Spring | 24.4 ± 4.07 N·m | 18 ft·lb | p. 553 |
| Banjo bolt | 24.4 ± 4.07 N·m | 18 ft·lb | p. 554 |
| Suspension | 24.5 ± 3.5 N·m | p. 570 | |
| Front and rear arm | 48 ± 6 N·m | p. 574 | |
| Upper bolts | 47.5 ± 5.42 N·m | 35 ft·lb | p. 574 |
| Rear shock absorber | 24.5 ± 3.5 N·m | p. 575 | |
| Nuts and bolts | 24.4 ± 4.07 N·m | 18 ft·lb | p. 575 |
| Center shock absorber | 48 ± 6 N·m | p. 576 | |
| Center shock absorber | 70 ± 10 N·m | p. 576 | |
| Rear arm top axle screws | 48 ± 6 N·m | p. 577 | |
| Pipe sealant | 13 ± 1 N·m | p. 584 | |
| Pipe sealant | 9 ± 1 N·m | p. 585 | |
| Pressure sensor | 27.1 ± 2.71 N·m | 20 ft·lb | p. 594 |
| Suspension | 13 ± 2 N·m | p. 602 | |
| Jam nuts | 18.5 ± 3.5 N·m | 164 in·lb | p. 605 |
| Runner nut | 8 ± 1.02 N·m | 71 in·lb | p. 606 |
Capacities
Values extracted from the document text. Check against the original before service work.
| Item | Value | Also | PDF page |
|---|---|---|---|
| Fuel tank | 36 L | p. 775 |
Spark plugs
Values extracted from the document text. Check against the original before service work.
| Item | Value | Also | PDF page |
|---|---|---|---|
| Spark plug | 0.4 mm | p. 472 |
Get the document
The full file is delivered by the bot. Free owner guides for Ski-Doo are also available from the manufacturer.
Open in Telegram — the bot finds this document by its catalog id and sends the file.
Open in bot- Official free Ski-Doo owner's manualsParts catalogueAll manuals