Ski-Doo MY21 E TEC 2021 Manual
Ski-Doo MY21 E TEC · 2021 · manual · 242 pages
Technical data
Numbers below were extracted automatically from the document. Verify them against the original manual before you order parts or apply torque.
Tightening torque
Values extracted from the document text. Check against the original before service work.
| Item | Value | Also | PDF page |
|---|---|---|---|
| Exhaust manifold screws | 33.9 ± 4.07 N·m | 25 ft·lb | p. 25 |
| Transmission | 5 ± 0.34 N·m | 44 in·lb | p. 58 |
| Transmission | 15 ± 1 N·m | p. 58 | |
| Water pump cover | 11 ± 0.8 N·m | p. 65 | |
| Bearing carrier screws | 5 ± 0.34 N·m | 44 in·lb | p. 70 |
| Coolant hose clamp | 5.5 ± 0.45 N·m | 49 in·lb | p. 72 |
| CPS retaining screws | 8 ± 0.45 N·m | 71 in·lb | p. 76 |
| Retaining screw | 125 ± 9 N·m | p. 80 | |
| Magneto housing | 7 ± 0.5 N·m | p. 81 | |
| Starter mounting screws | 11 ± 0.8 N·m | p. 86 | |
| Lubricate starter O-ring | 2.7 ± 0.7 N·m | p. 86 | |
| SERVICE PRODUCT screw | 2.7 ± 0.68 N·m | 24 in·lb | p. 86 |
| Retaining nut | 4 ± 0.3 N·m | p. 99 | |
| RAVE valve housing | 10 ± 0.7 N·m | p. 103 | |
| Collar nuts | 4 ± 0.34 N·m | 35 in·lb | p. 104 |
| Bracket | 20 ± 2 N·m | p. 105 | |
| RAVE cable lock nut | 20.3 ± 1.36 N·m | 15 ft·lb | p. 105 |
| Counter nut | 20 ± 2 N·m | p. 105 | |
| Snap ring | 20.3 ± 1.36 N·m | 15 ft·lb | p. 105 |
| RAVE cable lock nut | 5 ± 0.6 N·m | p. 105 | |
| Retaining plate screw | 5 ± 0.56 N·m | 44 in·lb | p. 105 |
| Bracket retaining screws | 11 ± 0.8 N·m | p. 107 | |
| REED VALVES Reed valve blade screws | 1.5 ± 0.3 N·m | p. 112 | |
| Intake adapter retaining | 6 ± 0.4 N·m | p. 113 | |
| Cylinder Head Warpage | 7 ± 0.2 N·m | p. 115 | |
| SEQUENCE Cylinder Block Base Gasket | 50 ± 1.5 N·m | p. 119 | |
| Linder Block Base Gasket | 50 ± 1.5 N·m | p. 119 | |
| Cylinder block screws | 50 ± 1.5 N·m | p. 137 | |
| Crankcase screws | 30 ± 2 N·m | p. 149 | |
| Oil seal cover screws | 11 ± 0.79 N·m | 97 in·lb | p. 150 |
| M8 Crankcase screws | 29 ± 2 N·m | p. 164 | |
| Fuel hose retainer screw | 5 N·m | 44 in·lb | p. 197 |
| Adapter plate clamps | 0.7 ± 0.1 N·m | p. 204 | |
| Throttle body clamps | 1.5 ± 0.23 N·m | 13 in·lb | p. 204 |
| TPS retaining screw | 4 ± 0.45 N·m | 35 in·lb | p. 206 |
| Spark plug | 17.5 ± 1.02 N·m | 155 in·lb | p. 214 |
| Ignition coil retaining | 2.4 ± 0.2 N·m | p. 217 | |
| Ground cable screw | 8 ± 0.45 N·m | 71 in·lb | p. 224 |
| Knock sensor screw | 24 ± 1 N·m | p. 226 |
Spark plugs
Values extracted from the document text. Check against the original before service work.
| Item | Value | Also | PDF page |
|---|---|---|---|
| Spark plug | 0.6 mm | p. 240 |
Get the document
The full file is delivered by the bot. Free owner guides for Ski-Doo are also available from the manufacturer.
Open in Telegram — the bot finds this document by its catalog id and sends the file.
Open in bot- Official free Ski-Doo owner's manualsParts catalogueAll manuals