Ski-Doo Chassis Gen5 Trail Manual
Ski-Doo Chassis Gen5 Trail · manual · 98 pages
Technical data
Numbers below were extracted automatically from the document. Verify them against the original manual before you order parts or apply torque.
Tightening torque
Values extracted from the document text. Check against the original before service work.
| Item | Value | Also | PDF page |
|---|---|---|---|
| Sensor retaining | 5 ± 1.02 N·m | 44 in·lb | p. 12 |
| Sensor retaining screw | 2.5 ± 1.02 N·m | 22 in·lb | p. 13 |
| Protection plate screw | 5 ± 1.02 N·m | 44 in·lb | p. 15 |
| SAS screw | 5 ± 0.96 N·m | 44 in·lb | p. 16 |
| Front shock absorber | 31.5 ± 3.5 N·m | p. 23 | |
| Retaining nuts | 31.2 ± 4.07 N·m | 23 ft·lb | p. 23 |
| Upper arm ball joint | 48 ± 6 N·m | p. 24 | |
| Lower arm ball joint | 48 ± 6 N·m | p. 26 | |
| Ski leg retaining nut | 47.5 ± 5.42 N·m | 35 ft·lb | p. 27 |
| Suspension | 3 ± 0.2 N·m | p. 31 | |
| Suspension | 3.1 ± 0.23 N·m | 27 in·lb | p. 31 |
| Front arm bolts | 47.5 ± 5.42 N·m | 35 ft·lb | p. 33 |
| Idler wheel nut | 18 ± 2.03 N·m | 159 in·lb | p. 33 |
| Center shock absorber | 48 ± 6 N·m | p. 37 | |
| Center shock absorber | 31.5 ± 3.5 N·m | p. 37 | |
| Shock absorber | 24.5 ± 3.5 N·m | p. 37 | |
| M10 x 40 screw | 61 ± 8.95 N·m | 45 ft·lb | p. 39 |
| Front arm lower bolt | 124.7 ± 10.17 N·m | 92 ft·lb | p. 41 |
| Link rods upper nut | 36.6 ± 1.36 N·m | 27 ft·lb | p. 42 |
| Rear shock absorber | 31.5 ± 3.5 N·m | p. 42 | |
| Suspension Assembly | 48 ± 6 N·m | p. 42 | |
| Steering Column and Tie-Rods - Rack | 12.5 ± 2.5 N·m | p. 49 | |
| Jam nut | 18.5 ± 3.5 N·m | 164 in·lb | p. 51 |
| Ski runner nut | 8 ± 1.02 N·m | 71 in·lb | p. 52 |
| Adjusting knob screw | 9 ± 1.02 N·m | 80 in·lb | p. 57 |
| Adjusting knob screw | 24.5 ± 3.5 N·m | p. 57 | |
| Indicator screw | 24.4 ± 4.07 N·m | 18 ft·lb | p. 57 |
| Multifunction switch | 2.4 ± 0.2 N·m | p. 59 | |
| Housing shell screw | 0.5 ± 0.11 N·m | 4 in·lb | p. 60 |
| Housing shell screw | 0.6 ± 0.11 N·m | 5 in·lb | p. 60 |
| Throttle lever retaining | 1.5 ± 0.2 N·m | p. 62 | |
| Steering Handlebar Handlebar | 1.5 ± 0.2 N·m | p. 63 | |
| Clamp screws | 24.4 ± 4.07 N·m | 18 ft·lb | p. 65 |
| Outer tie-rod end nut | 47.5 ± 5.42 N·m | 35 ft·lb | p. 66 |
| Inner tie-rod end nut | 24.4 ± 4.07 N·m | 18 ft·lb | p. 66 |
| Upper steering column | 12.5 ± 2.5 N·m | p. 68 | |
| Support nut | 12.5 ± 2.49 N·m | 111 in·lb | p. 68 |
| Lower steering column | 23.5 ± 3.5 N·m | p. 68 | |
| Support nut | 23 ± 4.07 N·m | 17 ft·lb | p. 68 |
| M8 Elastic nut | 24.4 ± 3.39 N·m | 18 ft·lb | p. 69 |
| Gauge support screw | 1.8 ± 0.23 N·m | 16 in·lb | p. 74 |
| Display bracket screw | 1.3 ± 0.2 N·m | p. 74 | |
| Display bracket screw | 1.4 ± 0.23 N·m | 12 in·lb | p. 74 |
| Intake duct clamp | 1 ± 0.23 N·m | 9 in·lb | p. 77 |
| Retaining screws | 1.8 ± 0.2 N·m | p. 77 | |
| Console nut | 6 ± 1.02 N·m | 53 in·lb | p. 78 |
| Front bumper nut | 5 ± 0.45 N·m | 44 in·lb | p. 79 |
| Side bottom pan screw | 2.8 ± 0.2 N·m | p. 82 | |
| Pinched nut | 2.8 ± 0.23 N·m | 25 in·lb | p. 82 |
| Side bottom pan screw | 2 ± 0.5 N·m | p. 82 | |
| Panel nut | 2 ± 0.45 N·m | 18 in·lb | p. 82 |
| Rear bumper screws | 16 ± 2 N·m | p. 83 | |
| Engine support screw | 27 ± 1 N·m | p. 98 | |
| Head screw | 0.5 ± 0.11 N·m | 4 in·lb | p. 98 |
| Oil tank clamp Torx | 1.25 ± 0.25 N·m | p. 98 |
Get the document
The full file is delivered by the bot. Free owner guides for Ski-Doo are also available from the manufacturer.
Open in Telegram — the bot finds this document by its catalog id and sends the file.
Open in bot- Official free Ski-Doo owner's manualsParts catalogueAll manuals