Ski-Doo RTX23 ACE SNOW 2023 Manual
Ski-Doo RTX23 ACE SNOW · 2023 · manual · 396 pages
Technical data
Numbers below were extracted automatically from the document. Verify them against the original manual before you order parts or apply torque.
Tightening torque
Values extracted from the document text. Check against the original before service work.
| Item | Value | Also | PDF page |
|---|---|---|---|
| Clamp | 4 ± 0.5 N·m | p. 25 | |
| Throttle body screws | 9 ± 1.02 N·m | 80 in·lb | p. 25 |
| Intake manifold screws | 9 ± 1.02 N·m | 80 in·lb | p. 32 |
| Haust manifold screws | 7 ± 1 N·m | p. 35 | |
| Drain plugs | 15 ± 2.03 N·m | 133 in·lb | p. 46 |
| Oil filter cover screws | 9 ± 1.02 N·m | 80 in·lb | p. 47 |
| Oil tank screws | 5 ± 0.56 N·m | 44 in·lb | p. 51 |
| ACE ENGINE cylinder | 11 ± 1.02 N·m | 97 in·lb | p. 51 |
| Sealing washer | 9 ± 1 N·m | p. 53 | |
| Aining screws | 17 ± 2 N·m | p. 54 | |
| Intermediate gear | 9 ± 1 N·m | p. 55 | |
| Oil pump cover screws | 9 ± 1.02 N·m | 80 in·lb | p. 57 |
| Intermediate gears | 17 ± 2 N·m | p. 77 | |
| Banjo bolt | 19 ± 2 N·m | p. 86 | |
| Water pump housing | 9 ± 1 N·m | p. 98 | |
| Water pump drive gear | 9 ± 1 N·m | p. 99 | |
| CPS retaining screw | 9 ± 1.02 N·m | 80 in·lb | p. 117 |
| Magneto cover screws | 9 ± 1 N·m | p. 118 | |
| Stator retaining screws | 9 ± 1.02 N·m | 80 in·lb | p. 121 |
| Sprag clutch housing | 30 ± 2 N·m | p. 124 | |
| Starter cable nut | 7 ± 1.02 N·m | 62 in·lb | p. 126 |
| Rotor retaining screw | 150.5 ± 9.49 N·m | 111 ft·lb | p. 136 |
| Screw plug timing | 17 ± 2 N·m | p. 143 | |
| Chain tensioner | 16.9 ± 2.03 N·m | 150 in·lb | p. 143 |
| Timing gear screws | 50.2 ± 2.71 N·m | 37 ft·lb | p. 144 |
| Gears | 50 ± 3 N·m | p. 144 | |
| CAPS retaining screw | 9 ± 1.02 N·m | 80 in·lb | p. 156 |
| Valve cover screws | 9 ± 1.02 N·m | 80 in·lb | p. 158 |
| Exhaust camshaft Camshaft | 5 ± 0.5 N·m | p. 160 | |
| Intake camshaft holder screws | 5 ± 0.45 N·m | 44 in·lb | p. 160 |
| Holder Screws | 9 ± 1.02 N·m | 80 in·lb | p. 161 |
| Cylinder head | 20.3 ± 1.36 N·m | 15 ft·lb | p. 166 |
| Exhaust camshaft holder | 9 ± 1.02 N·m | 80 in·lb | p. 184 |
| Camshaft locking tool | 5 ± 0.45 N·m | 44 in·lb | p. 184 |
| NOTICE screws | 9 ± 1.02 N·m | 80 in·lb | p. 190 |
| Breather cover | 9 ± 1.02 N·m | 80 in·lb | p. 205 |
| NOTICE Cylinder head | 9 ± 1 N·m | p. 214 | |
| Always screws | 9 ± 1.02 N·m | 80 in·lb | p. 214 |
| Cylinder Block | 23 ± 2 N·m | p. 229 | |
| Cylinder block | 9 ± 1 N·m | p. 229 | |
| Cylinder block | 20 ± 2 N·m | p. 229 | |
| M9 screws | 20.3 ± 1.36 N·m | 15 ft·lb | p. 229 |
| Knock sensor screw | 24 ± 3 N·m | p. 246 | |
| PTO cover screws | 23 ± 3 N·m | p. 249 | |
| Cylinder head | 23 ± 3 N·m | p. 276 | |
| Compressor wheel spinning causes filtered air | 1.1 ± 0.1 N·m | p. 299 | |
| BCV retaining screws sor outlet | 1.1 ± 0.11 N·m | 10 in·lb | p. 299 |
| Banjo bolts | 15.75 ± 0.75 N·m | p. 304 | |
| Clamp | 2.1 ± 0.23 N·m | 19 in·lb | p. 305 |
| Flange screws | 5 ± 0.56 N·m | 44 in·lb | p. 306 |
| Exhaust | 23 ± 3 N·m | p. 307 | |
| Flange screws | 23 ± 2.71 N·m | 17 ft·lb | p. 307 |
| Ignition coil retaining | 9 ± 1 N·m | p. 363 | |
| Spark plug | 13 ± 1.02 N·m | 115 in·lb | p. 364 |
Spark plugs
Values extracted from the document text. Check against the original before service work.
| Item | Value | Also | PDF page |
|---|---|---|---|
| ME1 | — | p. 175 | |
| M14 | — | p. 224 | |
| MR7BI-8 | — | p. 360 | |
| R8BI-8 | — | p. 360 | |
| MR8BI-8 | — | p. 386 |
Get the document
The full file is delivered by the bot. Free owner guides for Ski-Doo are also available from the manufacturer.
Open in Telegram — the bot finds this document by its catalog id and sends the file.
Open in bot- Official free Ski-Doo owner's manualsParts catalogueAll manuals