Ski-Doo MY22 Tundra Pdf 2022 Manual
Ski-Doo MY22 Tundra Pdf · 2022 · manual · 533 pages
Technical data
Numbers below were extracted automatically from the document. Verify them against the original manual before you order parts or apply torque.
Tightening torque
Values extracted from the document text. Check against the original before service work.
| Item | Value | Also | PDF page |
|---|---|---|---|
| Spark plug | 28.5 ± 1.36 N·m | 21 ft·lb | p. 40 |
| INTAKE SYSTEM subsection | 31.2 ± 4.07 N·m | 23 ft·lb | p. 54 |
| Snug all bolts | 33 ± 3 N·m | p. 54 | |
| Engine rubber mount | 24.5 ± 3.5 N·m | p. 63 | |
| Engine support screws | 42 ± 4.07 N·m | 31 ft·lb | p. 64 |
| Front Engine Support Replacement | 42 ± 4 N·m | p. 65 | |
| ENGINE RUBBER MOUNTS Engine rubber mount | 10 ± 2 N·m | p. 66 | |
| Muffler retaining screw | 7 ± 1.02 N·m | 62 in·lb | p. 77 |
| Exhaust Gas | 45 ± 2 N·m | p. 82 | |
| Temperature Sensor | 44.7 ± 1.36 N·m | 33 ft·lb | p. 82 |
| Exhaust pipe retaining | 7 ± 1 N·m | p. 85 | |
| Cylinder | 5.5 ± 0.5 N·m | p. 93 | |
| Head | 5.5 ± 0.45 N·m | 49 in·lb | p. 93 |
| Coolant hose clamp | 3.1 ± 0.45 N·m | 27 in·lb | p. 95 |
| Turbo engine | 2.5 ± 0.5 N·m | p. 103 | |
| Drain screws | 9 ± 1 N·m | p. 105 | |
| M6 screw on chassis | 10 ± 2 N·m | p. 172 | |
| Engine Ground | 31.2 ± 4.07 N·m | 23 ft·lb | p. 178 |
| Approved spark plug socket | 27.5 ± 2.5 N·m | p. 215 | |
| Engine Cut-Off Switch Continuity Test | 9 ± 1 N·m | p. 220 | |
| Battery terminals | 10 ± 2 N·m | p. 226 | |
| Battery hold down | 7 ± 1 N·m | p. 226 | |
| Bracket | 7 ± 1.02 N·m | 62 in·lb | p. 226 |
| Battery cover retaining | 7 ± 1 N·m | p. 226 | |
| Capacitor screws | 2 N·m | 18 in·lb | p. 232 |
| Solenoid cable retaining | 4 ± 0.5 N·m | p. 243 | |
| Taillight retaining screw | 0.8 ± 0.23 N·m | 7 in·lb | p. 264 |
| Retaining screws | 1 ± 0.23 N·m | 9 in·lb | p. 268 |
| Torx screw | 7.5 ± 1.02 N·m | 66 in·lb | p. 279 |
| Elastic nut | 10.1 ± 2.03 N·m | 89 in·lb | p. 279 |
| Clamping screw | 5.5 ± 0.45 N·m | 49 in·lb | p. 281 |
| Distorted spare belt | 10 ± 2 N·m | p. 285 | |
| Distorted spare belt | 24.5 ± 3.5 N·m | p. 285 | |
| Roller axle screw | 5 ± 0.45 N·m | 44 in·lb | p. 298 |
| Damper screws | 31.2 ± 4.07 N·m | 23 ft·lb | p. 299 |
| Drive pulley bolt | 120 ± 5 N·m | p. 300 | |
| Centrifugal lever | 5 ± 0.6 N·m | p. 308 | |
| Pivot nut | 5 ± 0.56 N·m | 44 in·lb | p. 308 |
| Spring cover retaining | 10 ± 2 N·m | p. 308 | |
| Bearing flange nut | 15.5 ± 1.47 N·m | 137 in·lb | p. 319 |
| Pivot screws | 17 ± 1 N·m | 150 in·lb | p. 330 |
| Brake lever pivot nut | 6 ± 1 N·m | p. 339 | |
| Brake lever pivot nut | 8.5 ± 1.5 N·m | p. 339 | |
| Brake caliper bleeder | 8.5 ± 1.47 N·m | 75 in·lb | p. 339 |
| Brake pad pin | 10.1 ± 2.03 N·m | 89 in·lb | p. 341 |
| Master cylinder clamp | 9 ± 1 N·m | p. 344 | |
| Washers | 27 ± 1 N·m | p. 344 | |
| Middle clamp nut | 2.3 ± 0.23 N·m | 20 in·lb | p. 346 |
| Middle clamp nut | 35 ± 1 N·m | p. 346 | |
| Caliper Banjo fitting | 35.3 ± 1.36 N·m | 26 ft·lb | p. 346 |
| Master cylinder Banjo | 27 ± 1 N·m | p. 346 | |
| Caliper Banjo fitting | 27.1 ± 1.36 N·m | 20 ft·lb | p. 346 |
| Magnetic check plug | 6 ± 1 N·m | p. 349 | |
| Drain plug | 6 ± 1.02 N·m | 53 in·lb | p. 350 |
| Bearing | 24.5 ± 3.5 N·m | p. 356 | |
| Actuator coupling | 7 ± 0.5 N·m | p. 368 | |
| 219100985-021-010 shaft nut | 7 ± 0.45 N·m | 62 in·lb | p. 368 |
| Upper gear screw | 48 ± 6 N·m | p. 380 | |
| Screws Same | 10 ± 2 N·m | p. 381 | |
| Reverse gear screw | 24.4 ± 4.07 N·m | 18 ft·lb | p. 381 |
| Rear idler wheel | 48 ± 6 N·m | p. 391 | |
| Retaining screws | 47.5 ± 5.42 N·m | 35 ft·lb | p. 391 |
| Rear idler wheel | 24.5 ± 3.5 N·m | p. 391 | |
| Cover retaining screws | 24.4 ± 4.07 N·m | 18 ft·lb | p. 401 |
| Cover retaining screws | 29 ± 3 N·m | p. 401 | |
| Shock rod nut | 28.5 ± 2.71 N·m | 21 ft·lb | p. 401 |
| Suspension | 3 ± 0.2 N·m | p. 410 | |
| Front and rear arm | 48 ± 6 N·m | p. 413 | |
| Rear shock absorber | 24.5 ± 3.5 N·m | p. 416 | |
| Center shock absorber | 40 ± 5 N·m | p. 417 | |
| Throttle rods upper nut | 36.6 ± 1.36 N·m | 27 ft·lb | p. 421 |
| Throttle rods upper nut | 24.5 ± 3.5 N·m | p. 421 | |
| Suspension | 24.5 ± 3.5 N·m | p. 424 | |
| Suspension | 48 ± 6 N·m | p. 425 | |
| 16in Wide Suspension | 1.5 ± 0.5 N·m | p. 427 | |
| Front arm upper bolts | 61 ± 9.49 N·m | 45 ft·lb | p. 432 |
| Front arm upper bolts | 82.5 ± 7.5 N·m | p. 432 | |
| Rear arm upper bolts | 82.7 ± 8.13 N·m | 61 ft·lb | p. 432 |
| Center shock shaft | 70 ± 10 N·m | p. 436 | |
| Retaining nut | 70.5 ± 9.49 N·m | 52 ft·lb | p. 436 |
| Center shock shaft | 85 ± 10 N·m | p. 436 | |
| Retaining screws | 85.4 ± 9.49 N·m | 63 ft·lb | p. 436 |
| Shock absorber upper bolt | 61 ± 9.49 N·m | 45 ft·lb | p. 439 |
| Unfasten stopper strap | 48 ± 6 N·m | p. 439 | |
| Front arm upper bolts | 47.5 ± 5.42 N·m | 35 ft·lb | p. 439 |
| Lower bolts | 61 ± 9.49 N·m | 45 ft·lb | p. 439 |
| Jam nut | 18.5 ± 3.5 N·m | 164 in·lb | p. 449 |
| Runner nut | 8 ± 1.02 N·m | 71 in·lb | p. 450 |
| Ski nut | 47.5 ± 5.42 N·m | 35 ft·lb | p. 451 |
| Adjusting knob screw | 9 ± 1.02 N·m | 80 in·lb | p. 454 |
| Adjusting knob screw | 24.5 ± 3.5 N·m | p. 454 | |
| Indicator screw | 9 ± 1.02 N·m | 80 in·lb | p. 454 |
| Indicator screw | 24.5 ± 3.5 N·m | p. 454 | |
| Multifunction switch | 2.4 ± 0.2 N·m | p. 457 | |
| Emergency stop switch | 2 ± 0.5 N·m | p. 458 | |
| Support retaining screws | 2 ± 0.45 N·m | 18 in·lb | p. 458 |
| Throttle lever housing | 1.9 ± 0.1 N·m | p. 458 |
Spark plugs
Values extracted from the document text. Check against the original before service work.
| Item | Value | Also | PDF page |
|---|---|---|---|
| Spark plug | 0.4 mm | p. 364 |
Service intervals
Values extracted from the document text. Check against the original before service work.
| Item | Value | Also | PDF page |
|---|---|---|---|
| Drive chain service | 500 km | p. 35 | |
| Coolant change | 5 years | p. 36 | |
| Engine oil change | 2 years | p. 38 | |
| Brake inspection | 3 years | p. 38 |
Get the document
The full file is delivered by the bot. Free owner guides for Ski-Doo are also available from the manufacturer.
Open in Telegram — the bot finds this document by its catalog id and sends the file.
Open in bot- Official free Ski-Doo owner's manualsParts catalogueAll manuals