Ski-Doo RTX22 ACE Snow 2022 Manual
Ski-Doo RTX22 ACE Snow · 2022 · manual · 406 pages
Technical data
Numbers below were extracted automatically from the document. Verify them against the original manual before you order parts or apply torque.
Tightening torque
Values extracted from the document text. Check against the original before service work.
| Item | Value | Also | PDF page |
|---|---|---|---|
| Intake manifold screws | 9 ± 1 N·m | p. 21 | |
| Throttle body screws | 9 ± 1.02 N·m | 80 in·lb | p. 22 |
| Connecting socket clamp | 4 ± 0.5 N·m | p. 22 | |
| MAPTS MAPTS retaining screw | 4.5 ± 0.45 N·m | 40 in·lb | p. 29 |
| Exhaust manifold screws | 7 ± 1 N·m | p. 36 | |
| BCV retaining screws | 1.1 ± 0.1 N·m | 10 in·lb | p. 45 |
| Banjo bolts | 15.75 ± 0.75 N·m | p. 50 | |
| Clamp | 2.1 ± 0.23 N·m | 19 in·lb | p. 51 |
| Exhaust flange | 23 ± 3 N·m | p. 53 | |
| Exhaust flange | 5 ± 0.6 N·m | p. 53 | |
| BPS BPS retaining screw | 4.5 ± 0.45 N·m | 40 in·lb | p. 62 |
| Compressor wheel spinning causes filtered air | 1.1 ± 0.1 N·m | p. 64 | |
| Drain plugs | 15 ± 2 N·m | p. 84 | |
| Oil filter cover screws | 9 ± 1 N·m | p. 85 | |
| O-ring | 9 ± 1.02 N·m | 80 in·lb | p. 85 |
| Retaining screw | 7 ± 0.8 N·m | p. 89 | |
| Cylinder | 11 ± 1.02 N·m | 97 in·lb | p. 90 |
| Regulator plug | 9 ± 1 N·m | p. 93 | |
| Regulator plug | 17 ± 2 N·m | p. 93 | |
| Intermediate gear | 9 ± 1 N·m | p. 95 | |
| Oil pump cover screws | 9 ± 1.02 N·m | 80 in·lb | p. 97 |
| Essure switch | 20.3 ± 1.36 N·m | 15 ft·lb | p. 114 |
| Water pump housing | 9 ± 1 N·m | p. 138 | |
| Water pump drive gear | 9 ± 1 N·m | p. 139 | |
| Magneto cover screws | 9 ± 1.02 N·m | 80 in·lb | p. 160 |
| Sprag clutch housing | 30 ± 2 N·m | p. 166 | |
| Starter retaining screws | 9 ± 1 N·m | p. 169 | |
| Screws M10 | 23 ± 1.36 N·m | 17 ft·lb | p. 169 |
| Starter cable nut | 7 ± 1.02 N·m | 62 in·lb | p. 169 |
| Screw plug timing chain | 17 ± 2 N·m | p. 189 | |
| Oil sump cover | 50 ± 3 N·m | p. 190 | |
| CAPS retaining screw | 9 ± 1.02 N·m | 80 in·lb | p. 203 |
| Valve cover screws | 9 ± 1.02 N·m | 80 in·lb | p. 206 |
| Camshaft | 5 ± 0.5 N·m | p. 208 | |
| Holder screws | 5 ± 0.45 N·m | 44 in·lb | p. 208 |
| Camshaft | 9 ± 1 N·m | p. 209 | |
| Holder screws | 9 ± 1.02 N·m | 80 in·lb | p. 209 |
| Cylinder head | 20 ± 2 N·m | p. 214 | |
| M9 screws | 20.3 ± 1.36 N·m | 15 ft·lb | p. 214 |
| Cylinder head | 9 ± 1 N·m | p. 215 | |
| Cylinder block | 20 ± 2 N·m | p. 277 | |
| Cylinder Block | 23 ± 1.36 N·m | 17 ft·lb | p. 277 |
| Cylinder block | 9 ± 1 N·m | p. 278 | |
| Rod screws | 12 ± 2.03 N·m | 106 in·lb | p. 287 |
| Cylinder block PTO side | 24 ± 3 N·m | p. 294 | |
| Timing chain guides | 23 ± 3 N·m | p. 323 | |
| ECM screw | 2.5 ± 0.45 N·m | 22 in·lb | p. 343 |
| ECM screws | 2.2 ± 0.2 N·m | p. 348 | |
| Reused bracket | 1.8 ± 0.23 N·m | 16 in·lb | p. 348 |
| Fuel rail retaining screw | 9 ± 1.02 N·m | 80 in·lb | p. 358 |
| Ignition coil retaining | 9 ± 1 N·m | p. 380 | |
| Troubleshooting a Fouled Spark Plug Spark plug | 13 ± 1.02 N·m | 115 in·lb | p. 387 |
Capacities
Values extracted from the document text. Check against the original before service work.
| Item | Value | Also | PDF page |
|---|---|---|---|
| Engine oil | 3.3 L | p. 398 |
Spark plugs
Values extracted from the document text. Check against the original before service work.
| Item | Value | Also | PDF page |
|---|---|---|---|
| M14 | — | p. 272 | |
| MR7BI-8 | — | p. 377 | |
| MR8BI-8 | — | p. 399 |
Get the document
The full file is delivered by the bot. Free owner guides for Ski-Doo are also available from the manufacturer.
Open in Telegram — the bot finds this document by its catalog id and sends the file.
Open in bot- Official free Ski-Doo owner's manualsParts catalogueAll manuals