Ski-Doo RTX23 E TEC Manual
Ski-Doo RTX23 E TEC · manual · 258 pages
Technical data
Numbers below were extracted automatically from the document. Verify them against the original manual before you order parts or apply torque.
Tightening torque
Values extracted from the document text. Check against the original before service work.
| Item | Value | Also | PDF page |
|---|---|---|---|
| Exhaust manifold | 34 ± 4 N·m | p. 23 | |
| Procedures screws | 33.9 ± 4.07 N·m | 25 ft·lb | p. 25 |
| Bearing screw | 8 ± 0.45 N·m | 71 in·lb | p. 33 |
| Retaining screws | 9 ± 0.56 N·m | 80 in·lb | p. 34 |
| Water pump cover | 11 ± 0.8 N·m | p. 59 | |
| Coolant hose clamp | 5.5 ± 0.45 N·m | 49 in·lb | p. 60 |
| Bearing carrier screws | 5 ± 0.34 N·m | 44 in·lb | p. 64 |
| Taptite screws | 6 ± 0.68 N·m | 53 in·lb | p. 64 |
| Magneto and Starter | 11 ± 0.8 N·m | p. 68 | |
| Magneto flywheel | 125 ± 9 N·m | p. 74 | |
| Retaining screw | 124.7 ± 9.49 N·m | 92 ft·lb | p. 74 |
| Magneto housing | 7 ± 0.5 N·m | p. 75 | |
| Stator retaining screws | 10.1 ± 0.68 N·m | 89 in·lb | p. 77 |
| Retaining screws | 8 ± 0.45 N·m | 71 in·lb | p. 91 |
| RAVE valve housing | 10 ± 0.7 N·m | p. 96 | |
| Collar nuts | 4 ± 0.34 N·m | 35 in·lb | p. 96 |
| RAVE cable lock nut | 20.3 ± 1.36 N·m | 15 ft·lb | p. 98 |
| Rave cable lock nut | 5 ± 0.56 N·m | 44 in·lb | p. 98 |
| Pin | 20 ± 2 N·m | p. 98 | |
| Bracket retaining | 11 ± 0.8 N·m | p. 100 | |
| Reed valve blade | 1.5 ± 0.3 N·m | p. 105 | |
| Intake adapter | 6 ± 0.4 N·m | p. 105 | |
| Cylinder Head | 6 ± 0.45 N·m | 53 in·lb | p. 105 |
| Cylinder Head Warpage Cylinder head | 7 ± 0.2 N·m | p. 107 | |
| Cylinder block screws Cylinder Block Base Gaske | 50 ± 1.5 N·m | p. 111 | |
| Cylinder block screws Cylinder Block Base Gasket | 50.2 ± 1.36 N·m | 37 ft·lb | p. 111 |
| Retaining screws | 6 ± 0.45 N·m | 53 in·lb | p. 122 |
| M8 Crankcase screws | 29.8 ± 1.36 N·m | 22 ft·lb | p. 139 |
| M6 Crankcase screws | 11 ± 0.79 N·m | 97 in·lb | p. 139 |
| Oil seal cover screws | 11 ± 0.79 N·m | 97 in·lb | p. 140 |
| Crankshaft for procedure | 30 ± 2 N·m | p. 153 | |
| MAG side RAVE valve | 6 ± 0.7 N·m | p. 166 | |
| Retaining screw | 5 ± 0.34 N·m | 44 in·lb | p. 171 |
| Oil catch tank screw | 7.5 ± 1.02 N·m | 66 in·lb | p. 173 |
| Oil pump screw | 1.8 ± 0.23 N·m | 16 in·lb | p. 174 |
| Opened 0.4 V - 0.7 V screw | 24.4 ± 4.07 N·m | 18 ft·lb | p. 177 |
| Retaining screws | 11 ± 0.79 N·m | 97 in·lb | p. 180 |
| Fuel hose retainer | 5 N·m | p. 211 | |
| Otherwise, throttle body may have | 8 ± 0.5 N·m | p. 216 | |
| Throttle body clamps | 1.5 ± 0.23 N·m | 13 in·lb | p. 218 |
| Adapter plate clamps | 0.7 ± 0.11 N·m | 6 in·lb | p. 218 |
| TPS retaining screw | 4 ± 0.45 N·m | 35 in·lb | p. 220 |
| Spark plug | 23 ± 1 N·m | p. 229 | |
| Ignition coil retaining | 2.4 ± 0.2 N·m | p. 232 | |
| Ground cable screw | 8 ± 0.45 N·m | 71 in·lb | p. 238 |
| Knock sensor screw | 24.4 ± 1.36 N·m | 18 ft·lb | p. 240 |
Get the document
The full file is delivered by the bot. Free owner guides for Ski-Doo are also available from the manufacturer.
Open in Telegram — the bot finds this document by its catalog id and sends the file.
Open in bot- Official free Ski-Doo owner's manualsParts catalogueAll manuals