Ski-Doo Supplement 2019 Manual
Ski-Doo Supplement · 2019 · manual · 1746 pages
Technical data
Numbers below were extracted automatically from the document. Verify them against the original manual before you order parts or apply torque.
Tightening torque
Values extracted from the document text. Check against the original before service work.
| Item | Value | Also | PDF page |
|---|---|---|---|
| Spark plug I | 18 ± 0.7 N·m | p. 39 | |
| Brake caliper bleeder I | 8.5 ± 1.5 N·m | p. 44 | |
| Exhaust manifold screws I | 34 ± 4 N·m | p. 54 | |
| Muffler retaining screw | 7 ± 1.02 N·m | 62 in·lb | p. 59 |
| Exhaust Gas | 45 ± 2 N·m | p. 61 | |
| Temperature Sensor | 44.7 ± 1.36 N·m | 33 ft·lb | p. 61 |
| Coolant hose clamp | 3.1 ± 0.45 N·m | 27 in·lb | p. 91 |
| Bearing carrier screws I | 5 ± 0.3 N·m | p. 95 | |
| Magneto housing | 6 ± 0.4 N·m | p. 105 | |
| Lighten stator retaining screws | 10 ± 0.7 N·m | p. 108 | |
| Collar nuts I | 4 ± 0.3 N·m | p. 127 | |
| RAVE valve housing | 10 ± 0.7 N·m | p. 127 | |
| Rave cable lock nut I | 20 ± 2 N·m | p. 129 | |
| Bracket | 20.3 ± 1.36 N·m | 15 ft·lb | p. 129 |
| Bracket retaining screws | 11 ± 0.79 N·m | 97 in·lb | p. 131 |
| Bracket retaining screws | 4 ± 1 N·m | p. 131 | |
| Reed valve blade screws I | 1.5 ± 0.3 N·m | p. 135 | |
| Under screw head | 50 ± 1.5 N·m | p. 141 | |
| MS Crankcase screws I | 29 ± 2 N·m | p. 154 | |
| 219100912-014-009 M6 Crankcase screws I | 11 ± 0.8 N·m | p. 154 | |
| Head | 5.5 ± 0.5 N·m | p. 204 | |
| Water pump cover screws | 11 ± 0.79 N·m | 97 in·lb | p. 209 |
| Coolant hose clamp I | 3 ± 0.4 N·m | p. 209 | |
| Screws I | 6 ± 0.45 N·m | 53 in·lb | p. 223 |
| Lighten CPS retaining screws | 8 ± 0.45 N·m | 71 in·lb | p. 224 |
| Starter mounting screws I | 11 ± 0.8 N·m | p. 228 | |
| Clamps | 4 ± 0.3 N·m | p. 245 | |
| Collar nuts | 4 ± 0.3 N·m | 35 in·lb | p. 245 |
| Collar nuts | 10 ± 0.7 N·m | 89 in·lb | p. 245 |
| Intake adapter retaining | 6 ± 0.4 N·m | p. 253 | |
| Reed valve blade screw s I | 1.5 ± 0.3 N·m | p. 253 | |
| Cylinder head screws I | 28 ± 1 N·m | p. 256 | |
| Cylinder block screws I | 50 ± 1.5 N·m | p. 259 | |
| Oil seal cover screws I | 11 ± 0.8 N·m | p. 274 | |
| Fuel hose retainer screw I | 5 N·m | 44 in·lb | p. 313 |
| Throttle body clamps I | 1.5 ± 0.2 N·m | p. 319 | |
| Adapter plate clamps I | 0.7 ± 0.1 N·m | p. 320 | |
| TPS retaining screw I | 4 ± 0.5 N·m | p. 322 | |
| Fuel injector retaining screws alter | 40 ± 1 N·m | 30 ft·lb | p. 347 |
| Fuel rail retaining screw s I | 8 ± 0.5 N·m | p. 353 | |
| Ignition coil retaining | 2.4 ± 0.2 N·m | p. 398 | |
| Lighten Absolute CPS screws | 2.5 ± 0.34 N·m | 22 in·lb | p. 418 |
| Retaining nuts | 5 ± 0.45 N·m | 44 in·lb | p. 421 |
| Ground cable screw I | 8 ± 0.5 N·m | p. 429 | |
| Knock sensor screw I | 24 ± 1 N·m | p. 431 | |
| Ground cable screw | 8 ± 0.45 N·m | 71 in·lb | p. 439 |
| Drive belt guard support | 7.5 ± 1 N·m | p. 446 | |
| Torx screw | 7.5 ± 1.02 N·m | 66 in·lb | p. 446 |
| Elastic nut | 10.1 ± 2.03 N·m | 89 in·lb | p. 446 |
| Clamping screw I | 5.5 ± 0.45 N·m | 49 in·lb | p. 447 |
| Roller axle screw | 5 ± 0.45 N·m | 44 in·lb | p. 461 |
| Damper screws | 5 ± 3.5 N·m | p. 462 | |
| Damper screws | 31.2 ± 4.07 N·m | 23 ft·lb | p. 462 |
| Cam screw | 5 ± 3.5 N·m | p. 471 | |
| Cam screw | 31.2 ± 4.07 N·m | 23 ft·lb | p. 471 |
| Bearing flange nut I | 15.5 ± 1.5 N·m | p. 472 | |
| Brake pad pin I | 10 ± 2 N·m | p. 478 | |
| Caliper screws | 24.4 ± 4.07 N·m | 18 ft·lb | p. 481 |
| Washers | 35 ± 1 N·m | p. 481 | |
| Brake lever pivot nut I | 6 ± 1 N·m | p. 482 | |
| Master cylinder clamp screws I | 9 ± 1 N·m | 80 in·lb | p. 482 |
| Middle clamp nut | 2.3 ± 0.2 N·m | p. 484 | |
| Middle clamp nut | 35 ± 1 N·m | p. 484 | |
| Caliper Banjo fitting | 35.3 ± 1.36 N·m | 26 ft·lb | p. 484 |
| Master cylinder Banjo | 27 ± 1 N·m | p. 484 | |
| Caliper Banjo fitting | 27.1 ± 1.36 N·m | 20 ft·lb | p. 484 |
| Drain plug I | 6 ± 1 N·m | p. 489 | |
| Bearing | 24.5 ± 3.5 N·m | p. 495 | |
| Front arm bolts | 47.5 ± 5.42 N·m | 35 ft·lb | p. 516 |
| Rear arm connecting | 61 ± 9 N·m | p. 516 | |
| Rod screws | 61 ± 9.49 N·m | 45 ft·lb | p. 516 |
| Clamp screws | 2.5 ± 0.45 N·m | 22 in·lb | p. 517 |
| Clamp screws | 0.4 ± 0.1 N·m | p. 517 | |
| Knob screw | 0.5 ± 0.11 N·m | 4 in·lb | p. 517 |
| Support screws | 5 ± 1.02 N·m | 44 in·lb | p. 519 |
| Support screws | 2.5 ± 0.5 N·m | p. 519 | |
| Clamp screws | 1.5 ± 0.5 N·m | p. 519 | |
| Banjo bolt | 24.5 ± 3.5 N·m | p. 522 | |
| Upper bolts I | 48 ± 6 N·m | p. 542 | |
| Front and rear arm | 47.5 ± 5.42 N·m | 35 ft·lb | p. 542 |
| Rear shock absorber | 24.5 ± 3.5 N·m | p. 545 | |
| Center shock absorber | 40 ± 5 N·m | p. 546 | |
| Spring retaining nuts I | 24.5 ± 3.5 N·m | p. 558 | |
| Hook retaining nut I | 9 ± 3 N·m | p. 559 | |
| Hook retaining nut | 9 ± 3.05 N·m | 80 in·lb | p. 559 |
| Pivot arm lower nut | 24.4 ± 4.07 N·m | 18 ft·lb | p. 568 |
| Pivot arm lower nut | 32 ± 4 N·m | p. 568 | |
| Pivot arm upper nut | 32.5 ± 4.07 N·m | 24 ft·lb | p. 568 |
| SCM retaining nut | 2.5 ± 0.5 N·m | p. 579 | |
| Jam nut I | 18.5 ± 3.5 N·m | p. 591 | |
| Runner nut | 8 ± 1.02 N·m | 71 in·lb | p. 592 |
| Ski nut | 47.5 ± 5.42 N·m | 35 ft·lb | p. 593 |
| Adjusting knob screw | 9 ± 1 N·m | p. 596 | |
| Adjusting knob screw | 24.5 ± 3.5 N·m | p. 596 | |
| Indicator screw | 24.4 ± 4.07 N·m | 18 ft·lb | p. 596 |
Capacities
Values extracted from the document text. Check against the original before service work.
| Item | Value | Also | PDF page |
|---|---|---|---|
| Fuel tank | 36 L | p. 646 |
Spark plugs
Values extracted from the document text. Check against the original before service work.
| Item | Value | Also | PDF page |
|---|---|---|---|
| Spark plug | 0.6 mm | p. 645 | |
| D01 | — | p. 888 | |
| Y18-008 | — | p. 1134 | |
| Y18-011 | — | p. 1202 |
Service intervals
Values extracted from the document text. Check against the original before service work.
| Item | Value | Also | PDF page |
|---|---|---|---|
| Drive chain service | 500 km | p. 691 | |
| Coolant change | 5 years | p. 692 | |
| Drive chain service | 1500 km | p. 1230 |
Get the document
The full file is delivered by the bot. Free owner guides for Ski-Doo are also available from the manufacturer.
Open in Telegram — the bot finds this document by its catalog id and sends the file.
Open in bot- Official free Ski-Doo owner's manualsParts catalogueAll manuals